Reviews
Fits: その他
Exclusive products are ultimately safer than Universal Products
The Ceramic resistor part of the LEDNumberSIDEBlinker made by ACTIVE was damaged and became a high flasher, so I bought it for repair. I am glad to know that I can install it easily! I would be happy if ACTIVE would continue to sell Repair Parts. View detail
Quite Compact
Used with 10R Fender less.
Generally as expected, but the Lens portion is quite thick, probably for light distribution.
It would have been better if it were shaped to be nearly flush with the Plate, so that it would be less present.
The wiring was done by attaching a male Bullet Terminal to the wiring of this product, connecting it to the POSH BlinkerConversion Connector, and using a very cheap Chinese Relay (Orange guy) as the Relay.
The wiring outlet was poor as it was, so we reinforced it with silicon clay called "sugru" and also a WiringBracket would be good to make the wiring fit the body of the car.
View detail
PetitCustom
In the past, I had an experience where I caught my bag on the license plate and bent the Number, so I reinforced it and PetitCustom.
The bottom part of the Base is long, so I installed a Paste Type Reflector.
View detail
It's cool
Replacing it with this product is stylish because it makes the car look like a foreign car. View detail
Very good
I haven't installed it yet, but it looks really cool, I can't wait to install it, I think it's a good product, even though the gold amount is a bit high. View detail
Lightweight and neat looking
I replaced it with their Fender Eliminator Kit.
Lighter weight around the rear, LED blinker, and
I installed it to make it nicer.
Together with the Fender Eliminator, it's probably 1kg lighter.
The Aluminum Anodized Black used is beautiful and
The base plate has the minimum area and thickness required for rigidity.
Blinker has recently released a Small Type as well, but
This one is almost the length of the license plate.
It doesn't feel different.
The following are some notes and improvements, though not drawbacks
You should be careful about the side bag itself because it will interfere with the side bag of Company T when you install it.
Blinker's Wiring is laid bare.
The part coming out of the blinker body that needs to be sealed is
You may not have to worry too much about it. (I don't know, but it could be an internal countermeasure.)
WiringLayout asks for Sense, and
It sounds difficult, but I hope it will be improved somehow, in a good way.
We did not use the supplied resistors and replaced the Relay to deal with the problem.
The picture of the wiring explanation is hard to understand. I wanted one simple circuit diagram to be attached.
View detail
Fits: Others Vehicles over 126cc
It's refreshing
Blinker seems to melt because the Slip-on Silencer used is quite up type So I bought it, I didn't use Ceramic resistors, but Relay to OEM Harness The White Wiring for resistors was used by connecting it as it is because the thing that seems to have been attached to it was used I used Vinyl Tape and wrapped it around Harness without connecting the View detail
Fits: Others Vehicles over 126cc
Rearreshing around Rear!
Because the OEM Blinker has broken down, I tried purchasing it at a great price. Result Succeeded with Makeover around Rear and I'm satisfied.. View detail
Fits: Others Vehicles over 126cc
good
Since it was also attached to the previous Motorcycle, I bought it without worry this time as well.
Especially since the front and back Blinker are protruding on the ZX - 12R, I did not want to leave OEM.
Wiring is somewhat troublesome for installation, but there are not so difficult things, so I think that it is somehow Level that someone who does not have installation experience.
Personally I think that it is cool, but I do not see much in the city surprisingly, so it is superfluous.
View detail
Fits: Others Vehicles over 126cc
Refreshing plan around GSR 400 Rear 2nd
Rearreshing around Rear 2nd plan
BlinkerRefreshing
Refreshing around Rear of GSR 400.
LED Blinker on License Plate Holder
As far as resistance against high flasher prevention is concerned, Japanese Vehicle Inspection Correspondence
Bullet Terminal processing is necessary, but it comes with no problems in particular.
In the case of GSR 400, the Blinker part comes in contact with the Exhaust System, so it is necessary to re-open the mounting hole.
It seems that water seems to be in the hole of the cord taking out so that it is also in other people's report, so Seal processing is done.
View detail
Fits: Others Vehicles over 126cc
Refreshing behind
I am in trouble with the processing of the back Blinker, a little expensive but purchase. It was dark but there was imprinting, but I think that it is necessary and sufficient brightness for Smoked lens.
There were also people who wrote Rose Tsuki in the arrangement of LEDs, but it would be too much of a mind. More than that, Quantity : Pair (for Left and Right) Merit who loses Blinker overhanging to him is far Large.
I think that I will continue to use this even if I switch to Motorcycle.
View detail
Fits: Others Vehicles over 126cc
I do not want to make it stand out anyhow
I bought it for BlinkerRefreshing.
When using it I am satisfied because it will properly fulfill the role of Blinker. I am glad that the price is cheaper a little (sweat
View detail
Fits: その他 Vehicles under 125cc
Can accommodate various Custom
I used it for a solo customized around Rear.
When I turned off the Fender or removed extra things, the Blinker installation site disappeared and I was looking for a substitute item.
Image of SS and so on if it is a product of this hand, but it fits casually, so it is possible to correspond to Chopper system and Ska tune.
It would be nice if the price is a bit cheaper - - -
I am convinced because I am solidly making it.
View detail
Fits: その他 Vehicles under 125cc
Since he wanted to improve visibility, it purchased. The description was kind and legible. Depending on a vehicle type, since capacity and resistance are insufficient, resistance of accessories needs to exchange depending on the case. It seem
Since he wanted to improve visibility, it purchased.
The description was kind and legible.
Depending on a vehicle type, since capacity and resistance are insufficient, resistance of
accessories needs to exchange depending on the case.
It seems that furniture is good in Ninja250R at least at Bai.
Since it will become a High flasher if it remains as it is, cautions are required.
Although I thought that it was based on operating environment, at the time of me, the attachment part of the Blinker broke and the Blinker was loitering ...
There may be a problem in durability.
View detail
Fits: その他 Vehicles under 125cc
It attached to the fender less made from A-TECH by D-tracker125. By exactly, the just fit is carried out to the width of the fender less. It seems that reinforcement was worrisome since the fender less was FRP, but it is satisfactory. When the
It attached to the fender less made from A-TECH by D-tracker125.
By exactly, the just fit is carried out to the width of the fender less.
It seems that reinforcement was worrisome since the fender less was FRP, but it is satisfactory.
When the carrier was loaded with the load, the visibility of the normal blinker was worrisome, but it is problem solving by this blinker.
Attachment was not so difficult, either and it carried out it to the extent that it worried about management of wiring.
View detail