Reviews
Compliance with Laws and Regulations
Installed on a last model CB400SF. (Molds after 2019)
Legal restrictions such as the angle of the Number are strictly enforced depending on the year and the time of first year registration.
This product is sturdy enough to comply with vehicle inspectionsLarge because it is compliant with angles and other requirements.
However, we have been told that some DREAM stores may uniformly consider Motorcycles of the regulated year as Fender EliminatorNG,
In the meantime, I decided to keep the Normal fender as well.
I did the work by myself and was able to complete the work without hesitation due to the detailed Instruction Manual. 8mmSocket, 10mmSocket, 3-4-5mm Hexagonal, 10mmSpanner, Radio pliers, thin Slotted screwdriver
The keyhole for the SeatOpening is different from that of other Fender Eliminator models. (Prayer is all we can do now.) …
It generally took about an hour.
Design and finish,
There is no Japanese Vehicle Inspection Correspondence for the latest regulations other than this one, so there was no choice. I did get the Refreshing, but I give it a 3 star rating.
Ideally, I would like it to be a little higher, further back, and angled. I don't have a choice.
The accuracy of each Part is high, and the Laser marking in Small is just right and gives a sense of ownership.
You will also want to change the Blinker.
View detail
Fits: KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2SX SE
I would like to see an effort to eliminate Option products.
Fender Eliminator had been using Active, so I bought it at Timing, where I had just finished inspecting the car.
It is unfortunate that the price became expensive because we purchased two Option Blinker and Bracket at the same time because we did not want Pannier to be out of the market. I think the product is insufficiently considered in this respect.
Also, although the simultaneous tightening of the License Plate Bracket and the License Plate can reduce the number of parts, it is disappointing that there is no texture.
The installation was the worst because I have a Bracket for GIVITop case, but I think it would be easy to install under normal circumstances.
If you do not use Pannier, which is also an Option consideration, I can recommend it.
View detail
Used for VERSYS1000SE
Used for VERSYS1000SE.
Puig, R&G appeared, but there was a need to replace the blinker and processing of the License Plate Light.
The reason why I chose this product is that Ninja1000 and Fender have the same part number in the OEM part number.
Then, I thought, "Well, maybe we'll just get there. I was just going with the flow.
The results did not arrive as they were.
For now, put a 20mm~25mm Spacer from under the Seat to fix the Fender Eliminator.
45mm Spacer at the Blinker Bracket.
Changing the Others and Bolt will be just about right.
If the Seat is not to be opened or closed, or if the key is to be relocated, a 45mm Spacer is not needed.
Also, if you do not use the OEM Pannier case, the OEM can use the Blinker.
This was not necessary in HepcoAnd Becker's Side case.
No modification is done as we just insert the Spacer and change the length.
View detail
feeling refreshed
[How is it used?
I used this to remove the characteristic Fender of Center Up
Was the one you received as per Image?
It turned out exactly as shown in the picture.
The cleaner look makes it more photogenic and easier to photograph.
Was the installation difficult?
Compared to other car models, there were more parts to be removed, so I felt it was more labor intensive.
I thought it would not be too difficult because I had some idea of what I was going to do beforehand, such as with the video Site, and did the work.
How was your experience with it?
Since the Fender will be gone, there may be more winding of the Rear than before.
(I haven't experienced it yet)
[Included Parts:were they on?
There was a set of parts to be installed on the car and a simple instruction manual for installation.
[Was there anything that disappointed you?
From the back, it looks slim and good, but from the side, it looks a bit more.
Maybe it was the Center UpLayout part that made me feel that way, unlike the current style of SS.
Instruction Manual is included in the package, but I think it would be easier for first-time users to imagine the work and proceed after watching a video or something.
View detail
fenderless kit
About quality and texture be of average quality About the feeling of use I had to combine the other kits It is too short to install in ape100 Products to buy together 0900-529-10301 Blinker could be installed using Universal Bracket Difficulty of installation It's not a perfect product. It's a product that needs to be customized Cost performance and comparison with other products My bicycle dirt tray is made of Takegawa, but I bought it because I thought there would be no big difference between the two products because the price of Takegawa and fenderless products was double, but there were many problems. About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I think this product is suitable for Ape50 It's not a bad product for Ape100, but the blinker position is moved too far back I couldn't install this fenderless product and move the bike behind the bike View detail
cheap
Fender Eliminator from ksStyle was not available, so we substituted it here
The number angle is a little loose, so if you want to raise the number angle precisely, use another manufacturer's number angle.
View detail
Even if it was attached simply and you carry out what time contribution, tell the reason for a send-off!
Even if it was attached simply and you carry out what time contribution, tell the reason for a send-off! View detail
Fits: KAWASAKI NINJA250, KAWASAKI NINJA400, KAWASAKI Z250, KAWASAKI Z400
Refreshing
The quality is good and installation is easy.
If you are going to make it a Blinker reply in the future, the look of this Kit with the Blinker Bracket still in place may not look so good.
View detail
Fender Eliminator
I used it on my GROM. The number was not as high as I thought it would be, but it's not a problem at all. View detail
The simplest construction among the things that can be attached to the GSX-R.
Product Name
ACTIVE Active Fender Eliminator Kit
Item Number
1155040
Vehicles
GSX-R1000R 2017
Number of man-hours
About 30 minutes
Why did you choose this product?
I bought it because I thought the OEM Fender was too large and I thought the whole body would be cooler with a lesser design.
Impressions after using it
The product is as expected, both good and bad.
Product Contents is a simple product, so there was no difficulty about installation.
If I had to say, it's not a messy design, so it's easy to blend in with the vehicle.
For myself, I prefer a matte surface finish.
Also, this is the fate of the Fender Eliminator.
When this product is installed, the back gets dirty well because it bounces up badly in the rain.
▼ Attention
It takes the exterior around Seat to install, so if you are not confident about the work, it is better to ask PRO.
View detail
Installation is a pain and Blinker Wiring is tight.
It's a little cheap.
The gap between the Blinker's Wiring is narrow and oppressive.
The stop-lamp wobbled a bit and the fit was not so good.
I guess it's an old product.
View detail
not very good
The long tail is a curious exchange.
The installation itself was painless, but it would have been better if there was a Seal to hide the OEM holes.
I'm particularly concerned about the square hole in the Center, so I'm going to buy a Rubber plate and sandwich it in.
View detail
I chose to do this for a reason
Fender Eliminator for the GSX-S/R125 is the first of six companies' products on webike We have been dealing with it, but other companies' products had the following negatives, so we chose this product through the process of elimination
Company E:Low price, but full of retrofits
Company D:"Fender Eliminator But for the fact that it's pretty much sticking out the back
Ad:LED License Plate Lamp is double-sided tape application type Cheap (reportedly it will be ruined over time)
Company L:Too extravagant with many Bolts
Company S:The price is too high
On the occasion of installation, it is quite Large strange, because it is necessary to remove the Rear circumference secretly
There is an instruction manual with a picture, but......... "WhiteBlack, So, no Explain It's not in the
Just from the ACTIVE website Color You can download the instruction manual of the "M.I.T.", so I recommend you to use that one
As it stands now "Number When "Blinker is well organized and I think it's neat
There are two points to note
1 'Bounce off the rear wheel.' is amazing
It's especially easy to see when driving in rainy weather, Rear Sets and Cowl area become sticky and dirty Also, it enters into the Seat Cowl through the gap of Fender etc Moreover, it invades into Seat Cowl through the gap of Fender etc I think that this is the fate of Fender Eliminator, but...
2.Rear reflective material is not included
I think this is a pretty big deal... This product comes with a red colored rear reflective material It is not available and must be purchased separately It is a violation of the Road Traffic Law if you drive on public roads without it
"Tying The intention may be that you should buy it at The Seal type reflective material that was sold at Home Center's Cut-Off Corner "License Plate Light I'm sticking it in the
Let's face it, there's no such thing as a Fender Eliminator The "look just because "Functionality" There is no Merit at all in the product
Just my opinion It's cooler I'm just happy to be able to think that this is a good thing
Oh, and in a P.S "Availability When "Deadlines is always a good idea to check
I'm a Manufacturer, but I'm also a missing item, so to speak "BackOrder It was in good condition, but it took me 2 months from ordering to getting it in hand …
View detail
So so
Overall, though, it's good
The part of the License Plate Light where Wiring comes in is
Because of the gap at the top
I'm afraid I'm going to get water
Wiring position or
If it is treated with WaterproofBush, etc
I think it's good
I filled it with ButylSeal
View detail
A little more
The installation instruction manual is written in both APE 50 and 100 It's hard to understand
Also, it would be helpful if you could describe the tail lamp OEM removal and installation in more detail
I would like the Base plate to be a little longer when installed I am worried about the gap
View detail
Fits: KAWASAKI NINJA H2 SX, KAWASAKI NINJA H2SX SE
The Pannier case will be scratched up
I don't think of attaching the Pannier case to this product at all, because the Pannier case and Blinker hits the gut! So the Pannier case is now covered in scratches
I took a 1.5 cm collar and shifted it backwards to make a hole in the License Plate Light with Drill and put Number on it
I managed to install the License Plate Light with a bracket, but I was able to do it hELLIP;
It took a lot of work to get it into shape here
Active, why didn't you consider the Pannier case ( ; ;)
View detail
so-so
With the help of a friend, I managed to install it, but it was difficult to do so on my own
Also, I wish I had put a Reflector on it, because Sticker doesn't go in
Because there is no Plate frame, the Plate bends quickly
View detail
It does not match the LED Blinker of MT-09 OEMOption
Looks like OEMOption's LED Blinker and the root 1. About 5 cm hidden by Number,
The LED part is also hidden.
Although there is no problem in practical use, the automobile inspection will not pass.
Whether you extend the length with Spacer,
Return to STD Blinker,
Do you want to find another Blinker ...
View detail
I think that it is like this
We installed in L7GSX-R. Originally the shape of the installation site changed a bit, so Manufacturer side saw a sense of hardship. I think that it would have been better if the shape was a little more narrowed the width of Blinker. But compared with NORMAL, I think that it will become SMART and fit in Compact. View detail
It is quite good feeling
I am solidly synthesized..
The making of each Parts is also beautifully finished..
It is good to have Coupler and fine BlinkerWasherParts.
License Plate Light's LED is a bit disappointing.
Regrettably, the fabrication of the Bracket division is regrettable.
I feel it's expensive a little !?.
View detail