Reviews
Pre-installation impression
The Instruction Manual was not included in the package, but can be found on the product page of the official ENDURANCE website. It is recommended to check the contents before purchasing.
The product is made of steel sheet gold, so it does not have a luxurious feel, but the machining precision and the texture of the paint are good, and it does not look so cheap.
The ENDURANCE Logo is a Sticker, so you don't have to put it on if you don't need it.
Low head cap bolt for Case mounting (M6, hexagon socket) and HexalobularBolt for fixing the lid (M5) was included in the package.
Hexalobular (Torque) was supplied with a Wrench, but a 3mm Hexagonal Wrench and 10mm Spanners are required to tighten the Cap bolt.
To store the ETC in the Case, simply affix a protective sponge tape to the Case and place it inside.
Since this is a universal product, it is necessary to arrange an appropriate bracket separately for installation on the car body.
The dimensions of the holes available for installation were described in the Instruction Manual for handling.
The case does not have waterproof or dustproof features, but I think this is sufficient because it prevents direct exposure to rain in addition to the waterproof feature on the ETCBody side.
In general, it is sufficient for my needs, but I feel that the price is a bit expensive since there are many other with-key products available for a little more money.
View detail
fall
If I put it on Normal seat, I think it will be a little forward and downward.
My Seat has no problem because I have removed the anchor, so the Seat is like a crescent moon, and the footing is even better.
View detail
DriveRecorder for quality
Balance between price and performance (LED signals, nighttime images, front/rear shots, angle of view, etc.).
We chose this product based on our consideration.
Durability is undecided as we have just started using it.
View detail
Best equipment for winter
Great product for winter. Easy to operate. Wiring was easy as it is pulled in from the brake. View detail
Fits: HONDA Rebel 500, HONDA Rebel 250, HONDA Rebel 1100
I wanted Hook in just such a place!
[How is it used?
I was thinking that it would be better if there was a loading hook around the lower part of the Rear Carrier of REBEL1100 to stabilize the loading.
Was the one you received as per Image?
A loading hook with a width of 20 cm can be attached around the top of the RearStop-lamp.
Was the installation difficult?
Bolt On and it is ready to install. It takes only 5 minutes if you are familiar with it.
How was your experience with it?
I just loaded a backpack on a Tandem seat with a rope. The loading hook attached to the suspension was too large in width, and although it was sufficiently secured in the horizontal direction, it was not secured enough in the front-back direction. Even if a backpacket narrower than the width of the motorcycle is loaded, it is firmly fixed in the front-back direction, and the shaking of the luggage is reduced.
[Included Parts:were they on?
The Instruction Manual is now available on the Net, so the accompanying explanations are also simplified.
[Was there anything that disappointed you?
Digitize! I would like to see the Construction Instruction Manual attached to the product without being digitized! I would like to see the Construction Instruction Manual attached to the product without digitizing it...It would be nice to be able to refer to it on the Internet anytime, but what if the company's policies change or the company goes bankrupt and the WebSite disappears? Also, the QR code is only a LINK to the WebSite, so I have to search for it by tapping the part number, and it takes a lot of time to start the construction. Can't something be done about it...
View detail
Gorgeous.
I think it is the Large type among OEMOption and others.
Installation is easy, but there are some situations where it may get caught when getting in and out of the car because it is a large type.
Please consider those who have concerns about the high Seat height of the car.
View detail
Fits: HONDA CT125, HONDA SUPER CUB, HONDA CROSS CUB
Best Matches
It is for a CUB, but fits perfectly in Endurance's CenterCarrier. I put my Rain jacket, Goggles for the night, and charging cable in it. However, when refueling, the Seat closes, so you have to hold the Seat with your left hand while refueling with one hand, or with your shoulder while supporting the Seat with the other hand lol. View detail
It is a solid making
When installing, it was a bit of a hassle to assemble the auxiliary fixture to remove and attach the Rear Fender, but other than that, it was easy.
It is well made and useful.
View detail
Fits: HONDA DAX125, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA SUPER CUB110PRO
Mounted on CROSS CUBJA60
Installed for dress-up and ease of gripping.
My hands are on the Large size, but OEM is a bit far away and my hands get tired after riding long distances, so I bought this. I am glad I replaced it.
View detail
Fits: HONDA Super Cub 110 Pro, HONDA Super Cub 110 Pro, HONDA Super Cub 110, HONDA Super Cub 110, HONDA cross-cub
I recommend it!
Installed on CROSS CUBJA10
on purpose of installation
As the instruction manual says.
Some vehicles have to be shaved Crankcase
Quantity on the mating face of the Case:Pair (for Left and Right) Vehicles with upper and lower gaps in the
The hole where the Cylinder enters needs to be cut into a circle.
When assembled with the gapped cylinder, when the engine is applied and the cylinder expands thermally, it will cause the gapped cylinder to expand and the engine will not be able to operate.
It will not spread and will result in biting a new Piston!
The Gap of the Case cannot be checked unless the Normal cylinder is removed.
Then there is the work of processing the Case, so
It is safer to ask a motorcycle shop to assemble it.
I worked on two vehicles, mine and a friend's.
Both units had a top and bottom Gap in the Case mating area.
After cutting to a circle with Air Leutor, it was installed.
It is only 15cc bore up.
The effect is extremely Large, making Torque thicker and easier to use on a daily basis.
It is now easier to go uphill.
The parts we use also have HONDAMark on them.
Is it made in ThailandHONDA? I think it is reliable.
Regular Specification, and I think the difference is Recommendation
View detail
Fits: HONDA CT125 CT110 HUNTER CUB, HONDA CT125 CT110 HUNTER CUB
Meter visor even cooler than expected??
I purchased the ENDURANCE Meter visorLong set + installation kit for CT125.
I was a little excited when I unpacked the package because I had been planning to install this product for a long time....... The installation was easy and took only about 30 minutes without any stress, and it did not interfere with any surrounding parts.
Visor, which looked so small at first sight, now its presence is upgrading HUNTER to Wilde and I am very satisfied with it. ?? I am sorry for doubting.
Tightening is still the way to go. [Color] Smoke.
Thank you for a really good product.
View detail
ninja400 2018 Rear Carrier
[How is it used?
Install SeatBack
Was the one you received as per Image?
Street Image
How was your experience with it?
Is good
[Points to note]
It might be better to have someone from Support to do the installation.
How did it compare to other products?
I don't know, I haven't compared.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Fits: SUZUKI V-STROM250, SUZUKI V-STROM250, SUZUKI V-STROM250
It was a good purchase
Installation is not difficult if you have the proper tools and basic maintenance skills. The product itself is well welded, painted, and assembled with good precision.
I am glad I put it on because it changed the impression of the look and gave a sense of volume.
View detail
EnduranceRear Carrier for GROM late model
Installation is very simple:remove the Seat, push out the four hidden hole caps, and attach them there with the included screws.
Furthermore, the optional Helmet holder can be attached to the Carrier.
The Rear Carrier fills the empty space at the rear of the GROM and has a good design. The load capacity is 8Kg, which is stronger and more practical than the Honda OEM product. It was a good decision to buy it.
View detail
Bag and Quantity:Set and practicality at its best
The bracket on the underside could have been made a little more parenthesis. I attached the CenterCarrier bag for SUPER CUBCROSS CUB of the same manufacturer, and it went on without any problem. View detail
hmm
I'd bought the CB250R before because I'd heard it had a bad footprint.
I'm going to put it on.
Quality is good, almost OEM Product quality.
Almost indistinguishable from an OEM sheet.
The seat feels a little thinner, and the corners of the seat have been removed.
However, I don't think we should expect a Large width footprint improvement with this seat.
It's just a little bit. It's just a little bit. I feel like I have better footing.
View detail
Fits: HONDA cross-cub 110, HONDA cross-cub, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX HYBRID, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA LEAD125, HONDA LEAD125, HONDA LEAD125, HONDA Dio110, HONDA Dio110, HONDA Dio110, HONDA ZOOMER-X, HONDA LEAD110 EX, HONDA ZOOMER-X, HONDA LEAD110 EX
Easy!
It can be used for both navi110 and PCX150. It is cheap and not bad. I guess it's not so bad, but it's not that bad. View detail
Easy to install
Installation is really easy, taking less than 10 minutes. The texture is good, and the Pipe on the thick body is a nice parenthesis. If I have one complaint, it is that it is not designed to be installed with a helmet holder, even though it is an Endurance Carrier. Other than that, I am satisfied. View detail
For peace of mind
Purchased to protect myself and justify my own driving while driving on Motorcycle.
The product was relatively easy to install and complete.
It took some thought to run the Camera wires through the interior of the car body, but the rest of the connection was completed in comparative perspective.
The recorded images are clear and secure with no problems.
There is no GPS function, but the situation is satisfactory enough if you want to check the driving conditions.
View detail
High quality is realized, seems to be very practical.
[How is it used?
Myself, I don't like Guard, but to use it as a base for fog mounting.
Was the one you received as per Image?
Impressed with the cleanliness and precision of the finish. I think it is a good product for the price.
Was the installation difficult?
The 3 Bolts that suspend the Engine are replaced with the attached special Bolt, so basically, a Jack is required. I think it is easier to work with a smaller Jack.
How was your experience with it?
When I installed it and got on the car, I was impressed by the very high quality of the assembly, which was nicely aligned with the lines of the Radiator cover, as shown in the photo. I was very impressed with the high quality of the assembly.
I have never tried to rub it, but it seems to do the job of PROTECTION well.
[Included Parts:were they on?
The instruction manual is, well, easy to understand.
[Was there anything that disappointed you?
None in particular
Manufacturer conformity is after 2020, and Initial Model does not seem to conform.
The pipe diameter is 25.4mm, so the LED fog bracket fits a wide range of brackets.
LED fogs are in the works, but I will add them when they are installed.
I thought about installing the fogs on the handlebar, but since the R's sibling has a heavier headlight assy than the R, I did not want to add any more weight to the handlebar.
View detail