Reviews
Fits: HONDA CBR1000RR-R, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SB, HONDA CB400SB, HONDA CB400SB, HONDA CB250R, HONDA CB1300, HONDA CB1100RS, HONDA CB1100EX, HONDA CB1000R , HONDA 400X, HONDA 400X, HONDA 400X, HONDA 400X, HONDA 400X, HONDA CBR1000RR, HONDA CBR250R, HONDA CBR250R
So bad
I purchased this product because the color seemed to match. The texture and color were good, but unfortunately, the size of the Bolt part was different and could not be installed. View detail
Fits: HONDA CB400 SUPER BOL D'OR, HONDA CB400 SUPER FOUR
misaligned
The holes were not aligned and could not be installed.
I will never buy from them again.
View detail
Seat is torn
The KF18 had a good texture and was comfortable with no Seat tear after 3 years, but after the KF47, the Seat started to tear after about 3 months.
I have bought it twice, and both times, the same thing happened:it started to fray from the sewing part and spread out gradually.
The quality has really deteriorated. It's perfect for comfort.Quantity:2pc. Sold both sets.
We are now OEM and this has been sufficient.
This one has a lot of demerit, such as not being able to sit down right after it rains because it is a Type that absorbs when it gets wet.
I don't do Recommendation.
View detail
Fits: HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA CROSS CUB, HONDA CROSSCUB110, HONDA CROSS CUB50
Cannot be installed on JA60
I bought it because it is after JA45, but I cannot install it because it interferes with Chain Guard and Crankcase.
JA60 riders should not buy it.
View detail
I think the car model and Handlebar shape is very limited.
Quantity where the attached Belt is threaded through.:Pair (for Left and Right) There are two holes on the top, one on the back, and two on the top, but no matter which hole you put it through, it will be unstable to stop.
Also, the three belts are all the same length and are of the Velcro fastening type, so it would take some ingenuity to make the belts work with the handlebar fixed.
View detail
Fits: Others , YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-25, YAMAHA MT-25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA MT-03, YAMAHA MT-03, YAMAHA MT-07, YAMAHA MT-07 ABS, YAMAHA MT-07 ABS, YAMAHA MT-07
I can't put it on.
Pin holes for mounting on the body do not match.
Pin didn't fit and couldn't be attached.
View detail
Helmet hits the gut.
If you wear a full face helmet, it will hit the footpeg hard and damage it.
I ended up buying KIJIMA again.
But KIJIMA was lamer for the keys, so I used KIJIMA for the Bracket and Endurance for the Key Body.
The key Body has the same shape.
View detail
Fits: HONDA CB125R, HONDA CB250R, HONDA CB250R, HONDA CB125R
CoarseLargeGarbage
The screw holes are out of alignment and cannot be installed. View detail
I trusted the comments section and tried to buy it, but it did not arrive at the gixxer.
I trusted the comments section and tried to buy it, but it did not arrive at the gixxer.
Don't be fooled by the falsehood that the gap between the Light and the Grom is better for the Grom.
The stay does not attach to the brake master because it interferes with it, and the bolt that comes with it is too thin, so the OEM Product is used.
I had to return it to an auction house because I had opened the package.
View detail
Lens is slender. 6 months OR distortion or condensation when driving on roads with temperature differences.
When you cross the Hakone Pass on Route 1, the condensation orLens is distorted.
The first time I was able to get an initial response, but it happened three times in a row.
Just passing through Hakone Pass on Route 1 or near Ashikaga SA on the Tomei Expressway on a day when there is some temperature difference can break it.
It is vulnerable to condensation and should not be bought.
If it is only for town driving and mainly driven in places where the temperature does not change much, it may be Large sturdy.
View detail
Fits: HONDA CROSS CUB50, HONDA SUPER CUB 50, HONDA SUPER CUB 50PRO, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO
Doesn't fit a 22 year old super curve
First of all, I paid for the delivery in 2-3 days, but it arrived in 13 days. The delivery is slow and the blinker in question says that all the super curves of the previous year can be installed in the manual.
I have to process it to install it on a 22-year-old Super Cub.
The lens inside doesn't fit either --------------------------------------------- ------------- Once the shipping was paid for two or three days, the arrival arrived in 13 days. To do it, I have to process it.
The lens inside is not right. Powered by Google Translator
View detail
late delivery
Delivery date is 3 days later than when the order was placed.
There is also no CanCell button listed in the Cancellation method.
I will never buy from this Site again.
View detail
Fits: HONDA CB125R, HONDA CB250R, HONDA CB250R, HONDA CB125R
Too much shit.
It had been running without it for about 6 months after purchase.
I installed it because I am going on a long touring trip.
Honda Car Specialty Store ENDURANCE Endurance" I was also attracted by Shop's introduction that
When you are turning the 4 Bolts of the SupportBracket by hand in a temporary stop. It's hard..." I felt uncomfortable.
I was able to get about 1/4 of the way in by hand, but no more than that, so I used a latchet wrench to tighten it.
When I was almost there (about 1-2 cm left), it twisted off.
4 Bolts by the way (All Bolts) I felt uncomfortable at the
Remove one of the installed Screws and home center (Nafco) and while checking Bolt's Size, I went to
There is a hole in the home center to check the large size of the screws, but I found that the pitch is wrong.
The Bolt that was included in Carrier's Included Parts:did not fit. I purchased a bolt of the same size as the bolt I had threaded off, and after checking the size with the hole, it fit without difficulty. (Thus I believe the Bolt Pitch that Endurance sent me is different).
I'm an amateur so I don't know ha drill, but 6mm Bolt has a Pitch of 1.0. (Coarse) and 0.75 (Detail) I saw on the Net that there are two types of
Today I took it to Motorcycle shop and had Bolt taken out. (Chargeable)
I got myself together and tried to put Carrier on... The hole position is too different.
The supplied Bolt would not fit, so I dropped two sizes and tightened it down.
I thought it was the worst quality control.
I don't want to use such a Shop product again.
View detail
Salt response to initial defects
While there is also the product of the Fat Manufacturer of about 10,000 Yen, in order not to be troubled with the thing which does not function in the case of emergency, I dare to choose DriveRecorder of EduRans which is not cheap.
Before installing it in the vehicle, I checked on my desk to see if it worked properly and found that the Rear image was distorted and the recording was also recorded in a distorted manner.
I put the product back in the box and asked to return it, but was informed that they could not respond unless they could confirm the symptoms through inspection.
I reassembled it on my desk and turned it on again, assuming that I would have to prove the symptoms later, and the same symptoms appeared.
In addition, in the second verification, the disturbed Rear image was displayed in Red color.
Document the symptoms with photos and video and send the goods back for inspection, which the Manufacturer says will be done.
One or two weeks later, the manufacturer informs me that they cannot accept the return of the product because they cannot see any symptoms and that they will send the product back in its current condition.
The Button is also hard to push, and it is a product that I lost interest in installing in the vehicle. I wrote this so that the number of riders who feel the same way will not increase.
If you are referring to our products, we recommend that you select them after careful consideration because there are products of other manufacturers in the same price range.
View detail
Fits: HONDA CBR250RR, HONDA CBR250RR
Rust on Bearing
Bearing rusts.
Even if you remove the rust, when it rains, the rust will float to the surface.
Disappointed because it's not a cheap purchase.
View detail
Fits: HONDA Super Cub 110 Pro, HONDA Super Cub 110 Pro, HONDA Super Cub 110, HONDA Super Cub 110, HONDA cross-cub
I bought it because it said it fit, but it didn't fit at all.
I bought the product because it was on the fitment list, but the shape of the Head and Cylinder were completely different and it was not worth talking about.
I can't even return it because I've seen the fitment chart, checked it, bought it and opened the package.
Please don't make these fraudulent notations.
I've already talked to Webig and sent an email to Endurance.
We are also planning to consult with Consumer Center.
View detail
Fits: HONDA CB400SB, HONDA CB400SF, HONDA VTR250 typeLD, HONDA VTR250-F, HONDA VTR250
The thing is good, but it did not fit CB400SF.
Smoked Blinker Lens is included JFKFK334A02 (for VTR250) and the angle of notch on BoltBracket is different from CB400SF (2020) Front blinker.
You have to process (cut) it to get it on.
Either Endurance is wrong or Webike is wrong, but either way, be careful.
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA CROSS CUB, HONDA CROSS CUB50, HONDA CROSSCUB110
Installation is more troublesome than expected
At first I thought it was just a matter of removing one Screw and replacing it with the OEM Product, but it was completely different.
For some reason, the place where the root plugs in is longer than the OEM Product.
You have to remove the Pedal all the way to install it.
Plus, every time I try to position Pedal, I have to remove Pedal.
The workability was terrible.
I don't know about other Manufacturer's stuff, but I can't recommend this product.
View detail
Fits: HONDA SUPER CUBC125, HONDA SUPER CUBC125
There is a problem with the delivered product.
First of all, there is a problem with the packaging. The plastic wrap was torn. Bolts, nuts and washers are rolling around in the box. Thanks to this, there are no washers fastened to the windscreen. Second, the height and angle of the cradle mount are completely different. I adjusted the joint to set it, but there is a limit and I can't level it. I'm really angry. First of all, there is a problem with the packaging. The plastic wrap was torn. Bolts, nuts and washers are rolling around inside the box. Thanks to this, there are no washers that fasten to the windscreen. Second, the height and angle of the cradle mount are completely different. I made the setting by adjusting the joint, but there is a limit so I cannot level it. I'm really angry. translated by Google Translator View detail
Fits: HONDA GROM, SUZUKI V-STROM250, SUZUKI GSX-S125, SUZUKI V-STROM250, YAMAHA MAJESTYS, SUZUKI GSX-S125, YAMAHA MAJESTYS, HONDA PCX160, HONDA PCX160, HONDA PCX, HONDA PCX, HONDA GROM, HONDA GROM, HONDA GROM, HONDA GROM, SUZUKI V-STROM250, HONDA PCX150, SUZUKI GSX-S125, HONDA PCX150, SUZUKI SV650
Mis-designed Products
Although it is a thing of MAJESTYS conformity, it sticks when installing However, it is not a surface contact with the Handlebar installation part of the Clamp part, but a point contact This is a product that can be installed However, as an industrial product, it is a very suitable product because it gives priority to universalism Japan's Manufacturer has fallen Too bad, Endurance View detail