Reviews
Fits: HONDA PCX HYBRID, HONDA PCX, HONDA PCX150
Purchased based on appearance alone.
Purchased based on appearance alone.
Difficult to turn, Level gauge is hard to see
I think the quality must be good.
If you're willing to drop a little quality for a cheaper
View detail
Axel will not turn.
The screw on the Axel side is too long, and when it is tightened, the Throttle will not turn. I recommend you to use a m6×30 Screw. 35 might work, but I used 30. I wonder if the manufacturer has really tried it? I wonder. View detail
For practical users
NORMAL JA58, but installed ahead of time in anticipation of future Case installation.
Installation can be done by beginners. Even an inexpensive box wrench set can be used.
The mountainous point is when putting the Spring back in and when removing the STAND axis Screw.
Note that the STAND axis Screw is an Opposite Thread Screw.
The quality of the material is good, but either the jig is wrong or our vehicle is wrong.
Merit does not seem to fall over even when SIDE hung with luggage loaded in the cargo bed.
Durable due to solid color and structure, NORMAL looking.
Demerit is heavy (this is a TradeOff relationship with durability and reliability, so it can't be helped)
If you like the NORMAL style, don't carry luggage, or don't attach boxes, these parts are meaningless. It will only make the car heavier and worsen fuel consumption and steering stability.
It is designed for touring and people who carry a large amount of luggage.
View detail
Fits: HONDA MONKEY125, HONDA GROM, HONDA GROM, HONDA GROM
I fucked up.
After reassembling it, the Clutch was not cutting, and I looked at it closely.
jc92 out of conformity
View detail
Fits: HONDA CB250F, HONDA 400X, HONDA CBR400, HONDA GROM, HONDA CBR250R (2011-), HONDA CB400F (2013-)
Rattling occurred on ours.
Rattling occurred on ours.
I looked for a washer, but even the slightest difference causes the problem, so I have to put up with it without an ultra-thin washer.
View detail
solid construction
The price is higher than other manufacturers' products, but the construction is solid. Installation is easy, but I almost missed the included bolt and collar, which are located at the bottom of the box, under the cushioning material. View detail
stupid design
A big problem occurs when replacing the air cleaner (filter). One bolt of the air cleaner box cannot be removed due to the interference of the guard. According to the standard, you need to remove the guard, replace the air cleaner, and install the guard again. Very inconvenient. View detail
For CRF250L MD47.
When YOSHIMURA's Exhaust System is installed on CRF250L MD47, the Number and Exhaust System interfere with each other, so it cannot be installed.
MORIWAKI is EnduranceLarge sturdy.
DRC's Fender Eliminator Kit was Large sturdy even for YOSHIMURA!
View detail
Wind Cutting sound
We replaced the H2C Shield with this Smoke Shield.
I am not sure if I am big or not, but the Wind Cutting sound is very loud!
View detail
Fits: HONDA PCX HYBRID, HONDA PCX150, HONDA PCX150, HONDA PCX, HONDA PCX150, HONDA ZOOMER-X, HONDA PCX, HONDA PCX, HONDA PCX
There is a dress-up effect
The installation itself went without a hitch.
It is convenient to be able to adjust the width of the grip in six steps, but I don't adjust it often and I don't need this function.
The overall length of the Lever is long and difficult to grip.
I'm wearing a windshield, so when I cut the Handlebar to the locked position, it hits the windshield.
After using it for a while, I couldn't stand the discomfort and went back to OEMLever.
View detail
Screw...
When I attached the head lampBracket with the attached screw from the pure Normal Thread Screw, I was worried that the screw was too short and did not go in deeply. I have to change the bolt from OEM hex to normal home center. And the most important thing is that VisorBracket is connected in the middle next to Light Cover, but Screw hits Light Cover. Even if I adjust it forcibly, when I give the Light with the clearance of Limit 1mm, it hits the hanghang. Because I had no choice, I prepared a short Screw and changed it, but Nut was the last minute, so I put a thin Rubber on the gap with Double-sided Tape. View detail
Fits: HONDA PCX160, HONDA PCX, HONDA PCX eHEV, HONDA PCX, HONDA PCX eHEV, HONDA PCX160
You're just in my way.
I bought it to do a little customization, but the thickness of the Cover hinders me from pushing the SeatButton in, and when I push it hard, the Cover moves and is not stable. I removed it just because it was a hindrance, especially without improving parenthesis. View detail
Fits: HONDA GROM, HONDA PCX150, HONDA MONKEY125, YAMAHA MAJESTYS, YAMAHA MAJESTYS, SUZUKI GSX-S125, SUZUKI GSX-S125, SUZUKI V-STROM250, SUZUKI V-STROM250, HONDA GROM, HONDA GROM, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX, HONDA PCX HYBRID, HONDA PCX150, HONDA PCX150, HONDA PCX160
It is not easy to attach straight (horizontal).
It doesn't attach horizontally because the clamp hits at the Cable terminal.
It's hard to see the part that hits you, so I think people need to cut the Wiring without noticing.
The brake lever was shifted slightly outward to accommodate this.
View detail
Fits: HONDA VFR800, HONDA CBR1100XX SUPERBLACKBIRD
Adjuster is too far away to adjust
OEMLever of CBR1100XX is far (Small hands) I bought it because.
Adjusting the position with Dial's Adjuster (6 steps) is possible, but the Position closest to Lever (6 levels of "1") But it's far in the "middle" or so of the OEM adjustment range.
Therefore, other Position cannot be used, and it is no different from fixed Lever. (As far as my hands go.)
Too bad, because the texture is good.
It would be nice if the Adjuster had a wider adjustment range.
(Quantity:Pair (for Left and Right) (At first, the LeftLever of the "Mere Old Man" was shipped with a non-conforming one. Later, we were able to replace it with a compatible one)
View detail
The paint is ….
I ordered Black, but the Wound is terrible. I thought I would get it replaced because it was full of paint cracks and Small scratches, but it was a pain in the ass, so I Repaired it with Compound and installed it.
The paint was cracked by tightening the Handlebar Post, and the paint was peeled off by sliding the Axel Holder. And the price is higher than Buffing.
The handlebar shape and riding position are 30mm up from normal, so it's easier to ride and I'm happy with it, but the paint should be purchased on the premise that it will be painted by itself.
View detail
I use it with WAVE125.
[How is it used?
I use it with Wave125I of the commuter rapid train. However, there is no opportunity to utilize it while commuting.
I bought this product for a little day touring there.
Was the one you received as per Image?
I didn't have high expectations from the start, so Image is right.
The fabric should have been a little thicker, but when I didn't put anything inside, the bag was soggy.
How was your experience with it?
The double fastener with handlebar is easy to open and close even with Winter Gloves on.
It can hold a 500ml plastic bottle comfortably. I use it to hold a set of documents and tools, but the bag itself is not waterproof, so you need to put it in a bag beforehand to prevent water from splashing on it.
[Points to note]
When you access to the luggage space, the seat is lifted up, but it interferes with the bag.
I think it's a pain in the ass if Bag is a pumper or something.
Also, the Belt Adjuster is lousy for attaching to the Vietcarrie.
It's not that I can't use it, but I just can't get the Exactly Fit feeling.
If you're going for a just fit, remove the Vietcarrie once and install it after you put the Bag on.
How did it compare to other products?
none in particular
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
I want to get the Leather looks bag too!
View detail
Fits: HONDA VTR250, HONDA VTR250 typeLD, HONDA VTR250-F, HONDA CB400SB, HONDA CB400SF
Does not fit.
Processing is required for 2020 CB400SF
We need to cut down on Screw's place!
View detail
It makes the ride uncomfortable
The gap between the Tank and Seat is gone and looks better, but the posture is bent forward and my back hurts It will be So I've returned to NORMAL
View detail
Loading capacity 8kg?
* There is no such thing as a Tandem that weighs less than 8kg, do you know what that means?
An excerpt from the product description
Please do not exceed the load capacity (Maximum load capacity includes a Helmet holder, etc., attached to the Carrier The weight of everything is included.)
Honda OEM Tandem seat can be installed
By purchasing a Honda OEM Tandem seat separately, the seat can be easily installed and removed without tools It's done
It is both comfortable for Tandem and easy to use as a cargo bed
With a tandem grip, which is essential for a two-passenger car
The Grab is useful for Tandem, handling the vehicle and securing the luggage, etc It is equipped with a bar for peace of mind
View detail
It won't close
It looks good parenthesis, but it does not close all the way Even if I used a tool and tightened it tightly, it did not work After the purchase, I looked at a review of someone who bought the same thing on YouTube and they said the same thing I did View detail