Reviews
It's awesome!!!
Not only does the front-to-back position change, but the side stand is positioned a little further to the left, making the support much stronger. However, the downside is that the support is unstable with the original side stand, so you have to shorten the original side stand or install an adjustable side stand like I did. If you adjust it well, you can park stably on any road that slopes to the left or right. In fact, it would be enough to give it 5 stars, but since I am not satisfied with the combination with the original stand, I give it 4 points. -------------------------------------------------- -------- Instead of simply changing the front and rear positions, the side stand is placed a little more, and the support is very strong. However, the disadvantage is that the pure side stand is anxious. If you adjust it well, you can park it stably anywhere on the side of the road. In fact, it is enough to give five stars, but the combination with the genuine stand is not satisfactory. Powered by Google Translator View detail
Fits: HONDA CT125, HONDA CT110 HUNTER CUB
Stable even with heavy Rear
It is difficult to remove the Bolt and Nut of the OEMSide Stand, but the Bracket itself is easy to install.
The feel after installation is good. The STAND is located at the rear, but it is not difficult to apply.
The stability of the vehicle body with the Side Stand out is unmatched by the OEM.
View detail
OK
It has become stable.
I think the angle is a little too high.
Strength does not seem to be a problem because of the thickness of the steel plate.
View detail
Fits: HONDA CT125, HONDA CT110 HUNTER CUB
Reliable Side Stand
Side Stand can be used stably even with heavy loads in GIVI's Large type box (58L).
However, it is too close to the Center Stand and difficult to STAND while seated.
View detail
Fits: HONDA CT125, HONDA CT110 HUNTER CUB
Very large effect on overloading of the Carrier, which is common in CT125.
It increases stability to the point where OEMs are frustrated as to why they could not do this.
The balance of the OEM is such that the front of the Carrier floats when you press down on it with your hand, even when unloaded, and it changes to a sense of stability that does not waver when you put a little weight on it.
Installation is simple and straightforward, but a Torque wrench is required.
In particular, the bolt near the under bracket needs to be tightened behind the crankcase, so if the screw hole is broken by Overtorque, the entire crankcase will have to be replaced. If you are not confident about this, bring the bolt in or ask someone who is familiar with it to do it for you.
Side stands sensors can also be used without modification if the wiring is changed. All Bolts are specified with a specific Torque, so be sure to observe the Torque. This is also stated in the assembly manual.
One regret I have is that the Center Stand interferes with the BackOffset if a Side StandAdapteretc. is installed to increase the installation surface.
This must be addressed with the use of the anti-embedding Platec.
Nevertheless, the product is relatively easy to install and highly effective.
View detail
It would be nice to have for forest road driving and camping touring.
[How is it used?
On a slope such as a forest road "I'll stop. or as an auxiliary STAND on soft surfaces.
Was the one you received as per Image?
Image is correct. The strength is enough.
Was the installation difficult?
If you follow the manual, you will not fail. The tightening torque is also listed and easy to understand.
How was your experience with it?
It extends from a little behind the footpeg and has high stability on hard ground such as Asphalt.
If you try to STAND while seated, you'll almost step on the Kick pedal.
[Included Parts:were they on?
All the necessary bolts are included, GCraft's Right Side Stand was released earlier but it did not include STANDArm. This product is all-in-one and easy to understand. Don't forget to use the grease on the pipod.
[Was there anything that disappointed you?
The ”foot” of the STAND is the same as the NC750 series, and the area is small, and it is a little uneasy on the soft road surface. The stand plate (extended plate) for NC750 can be installed to increase the area of the foot, but the extended plate interferes with the center stand because the clearance between the center stand and the plate is tight.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
It's also the fact that it was on a CT110. "I wonder what it's like. I was curious about this, but I was very satisfied with the practicality.
It is regrettable that the area of ”foot”of STAND is too small. I think that many people who want to attach the Right Side Stand like this product to the rider's use scene are those who drive on the dirt with full of camping gear and stop on the soft ground for camping.
It would have been better if the area of the ”foot”was larger and less likely to sink on soft surfaces.
View detail
Recommendations for those who carry luggage
The C125 is unstable because of the position of the stand, and the front wheel floats up when the luggage is loaded on the top case.
So I installed this reinforced Side Stand Bracket.
The Side Stand mounting is retracted to the shaft of the Main Stand for added stability.
The installation process is simple and easy.
It would be easier if you have a Spring hook because you have to take the Spring on and off the STAND.
This is a Recommendation for those who load luggage on the C125.
View detail
I'm glad I changed it
Compared to OEMs, it's surprisingly tilted
It should only be a six-degree difference, but it feels like more than that
It's much more secure than OEMs
What I'm concerned about is that it doesn't jump up and down with Spring's power with a vigorous Scaupern like the OEMs do Place
It feels like a swoosh from start to finish
Of course, it doesn't come down while driving or anything like that
Also, it is very easy to put in and out of STAND because the hook is large
I like this one a lot
Also, I used a certain video as a reference for the installation, and in the video, when you attach the nut on the back It was explained to me that Spring had to be removed or the Wrench Socket wouldn't go in However, if you push up the Spring while the STAND is raised, the Spring is still attached But Socket is addictive
View detail
I think it's a bit short ……
If you have a tear stand, installation is easy It's done
The use of the STAND is a bit short … … I'm not sure if it's a bit short … … If the place where you wear it is dented, it tilts a lot
View detail