Reviews
Better than OEM
I temporarily installed this handlebar because I had to wait two months for an archi handlebar to be in stock, but it is easier to ride than the OEM one. It is easier to ride than OEM, but the aperture is not enough. If you have a hard time with OEM, it is worth a try. If you have a hard time with OEM, it is worth a try. View detail
It works, but …??
It is effective, but it seems like the Gel should be a little thicker. View detail
It's not bad
[How is it used?
V-string feels higher in adaptive height. Due to posture change.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It's not difficult as it's just a matter of replacing it. It is tedious, though.
How was your experience with it?
The same series I bought before had the hole positioned perfectly, but it was gapped by about 1cm, perhaps due to individual differences.
It's not hard to deal with, but if you don't have the tools, you may despair.
[Was there anything that disappointed you?
Since Handlebar is sold with pre-machined mounting holes, I thought it would be meaningless if the holes were gapped.
I think the Handlebar itself has a good texture and shape.
So far I've won one and lost one, so if I try it next time and the hole is Gap, I won't buy it again.
View detail
Too bad it didn't go in.
I wanted to attach it to the EZ-FIT TAPER BAR of the same manufacturerEFFEX, but it could not be attached because the rubber inside was too thick or it did not fit deep enough. I thought that I could attach it to the EZ-FIT TAPER BAR of the same EFFEX manufacturer, but it could not be attached. View detail
Bar Weight
I installed it together with a Handlebar of the same manufacturer. The vibration to the handlebar was also reduced. I also installed the same manufacturer's Lever at the same time. The only regret is the color, I wish there was a normal gold color instead of Champagne gold, View detail
Bar End
I think the vibration or reduced.
I think the color of Gold should be darker.
View detail
The effect is …?
The construction is solid and massive.
Because of the 400 single cylinder, we introduced it in the hope of reducing vibration transmitted to the Handlebar, but to be honest, we didn't really feel it.
I think it is good as a dress-up.
View detail
Compatibility with BEET
I installed this bar end on my Z900rs with BEET handlebar, but the throttle interferes with the bar end. I think they are not compatible with each other. The texture is beautiful and easy to install. View detail
I had it on my previous vehicle.
The brake lever has a rounded part so that it does not hurt the fingers. View detail
This was a necessary component for Handlebar replacement.
I was not familiar with the product and chose a product that many people had purchased.
The look is very normal, and since I had a Babyface Bar End on my STD Handlebar, I think I prefer Babyface for my personal preference.
I have yet to feel the effects of the vibration reduction. (I think he doesn't understand it because he rides less often and is a day trip Main…)
Note - After installation, when I tried to remove the AxelSlotPipe to replace it, the Rubber and Nut were left in the Handlebar and I could not get them out! I barely scraped out the rubber with a long stick and took out the nut with a magnet attached to the tip of a needle gold (without removing the handlebar). (Handlebar was solved without removing it). It may have already come off when I installed it. Be careful when turning it backwards.
Conclusion - The appearance is just personal preference. Vibration is also a novice, so you may get a good idea of the quality from this one.
View detail
Weighs close to OEM
I purchased this product because I wanted a weight close to OEM.
Vibration was definitely less than without.
A little heavier would be better for z900rs.
View detail
The pain in the buttocks was relieved, but ...
The vehicle in which it is installed is a Honda 400X. Sure, the degree of pain has lessened, but my sitting time is limited to an hour and a half.
For me, a height of 168cm, the 12mm increase in the seat height from 800mm has considerably increased my feeling of insecurity in terms of my footing.
Considering the cost performance, it was difficult to judge whether it was the right decision to purchase the items.
View detail
Bar weight installed in conjunction with handlebar replacement
It reduces vibration to a reasonable degree.
The most Large effect is Dress-up.
View detail
I need more weight.
I bought this Bar End for Steel handle because I replaced Handlebar with HURRICANEConti2 type. The weight of the Bar End is not so heavy, but I am not sure if the Steel handle is wrong or if the Bar End is not heavy enough, but my hands are numb after an hour of riding. Would a little more weight solve this problem? View detail
[Buying motive] He thought that he would unite by the same Brando, and it purchased. [Point which got interested] Ironic design which is not. Product ] which was seen as the candidate besides [ There was no compared product in particular. [aft
[Buying motive] He thought that he would unite by the same Brando, and it purchased.
[Point which got interested] Ironic design which is not.
Product ] which was seen as the candidate besides [ There was no compared product in particular.
[after-use comment] -- the accent of the circumference of a handle -- although it considered and red alumite was chosen, time takes for passing and has stopped being pleasing somehow
Tone of color alumite is not quite satisfactory somehow.
I think that I will exchange for the thing of black alumite in the near future.
as important bar weight, it is a function -- enough.
without it seems that SHIBIRE comes to a hand even if it will run 600 km ~ 800 km on the first -- a handle -- also getting the jitters -- it is not worrisome.
[Comprehensive evaluation] That liking of it has changed later this time carries out a recommend to those who it is not good and like the tone of color alumite, and those who are using the same Brando's handlebar.
View detail
Gel is easy on the hips.
I have been riding ZEPHYR1100 for 25 years. I guess the urethane is too hard, not the spongy one, but the hardness of the urethane. The combination of the decline of the buttock muscles and the shabby rear suspension made it impossible for me to ride for 5 hours. I had groin pain and lower back pain.
I thought about uncoating, but my dad at Motorcycle shop recommended this. No problem to install.
The effect on touring is not yet, but when I use it for commuting, I have a feeling that the Gel absorbs fine vibrations. The sticky feeling is good. It is 1cm thick, but I don't mind the footing. There are some wrinkles from sagging, but it does not bother me when I sit on it.
View detail
Reduced aggression to buttocks
I was looking for a sample of this product at MotorcycleWorld, and when I tried it on, I felt the effect, so I bought it. View detail
What's the effect?
I installed it to reduce vibration and also to protect the Bar End.
What are the effects I can feel, such as reduced vibration? The answer is yes.
Depending on the motorcycle you install, you may be able to see the effect.
View detail
Slight relaxation
I use it on my WR250X
I asked a motorcycle shop to replace the seat cover at the same time.
When you ask a motorcycle shop to Make sure they're exactly on the same side. Ya I'd rather just install it than pay for the labor." I think it's better to communicate your requests such as
In the case of a pontoon, since a foreign object is added to the seat, the footing will naturally be worse and the seat will look bulky.
I've been driving a bit after installing it, but honestly, it doesn't seem to have much effect.
I think I bought myself some time before my butt started to hurt, but what hurts is going to hurt.
It's a good way to prevent butt pain, but I'm not sure if it's worth the cost.
View detail
It's a very ordinary Heat Shrink Tube.
Used to fix a wrap-around Grip heater.
I used to use a common Heat Shrink TubeTube that is also sold at Home center, but I was a little concerned because it was slippery or compatible with Glove.
It's in the product description.
The surface is designed to be non-slip and secure.
I bought this book because I was attracted by a sentence that says
In conclusion, it is the same with Large. Rough operation, if you are not careful, it will slip.
If you don't care about the manufacturer or the pattern, Recommendation is not for you.
I bought a cheap heat gun from Amazon for installation. (It's not that hot) I worked with it, but this product was easier to shrink and I had the impression that it was less loose when I heated it up again using the Grip heater.
Overall, I don't recommend it, but I think it can differentiate itself from other users who use Heat Shrink Tube. The price is a little bit high.
View detail