Reviews
It got brighter.
Replaced Headlight Bulb on Z125PRO.
The purpose was not only to make the engine brighter, but also to reduce the load on the battery (power saving). The Z125PRO had LED lights from the beginning, so there was no need to replace the tail lamps. I thought about replacing the blinker light because it has a normal bulb in it, but I decided not to do it because the blinker relay seems to be built into the meter and it would be complicated to change it to LED. This time, I decided to replace the Headlight Bulb and the Position Lamp with LEDs, and for the Headlight, I chose this product, which was the cheapest among the Sphere Light products.
The replacement work was as simple as removing the headlight cowl and replacing the valve with the original one, and since the valve is compact, there were no problems with installation.
As for the feeling of use, the light is bright enough and feels very bright, probably because the light is whiter. I was able to drive safely at night. I was not bothered by the dispersion of the light. Unfortunately, there was not enough of an energy saving effect that I could really feel.
Compared to when we replaced the LEDValve on our ZRX1100 a few years ago, low-cost products are now on the market, and the hurdle for replacement has gone down. If you are concerned about the brightness of your lights, we recommend replacing them with LEDs.
View detail
Attached to Glass Lens with Cut
I put it on my old CIBIE CutGlass Lens, which is 4500K, but it is not too white, which is good. I heard that cheap lenses may scatter light because they are old, but this was not the case, and it became brighter anyway. View detail
Explosive light, but not compatible with Off-roadFender
H4 Valve replacement Type, so replacement is easy.
Valve size is the same as Halogen bulbs, so there is no need to worry about replacement work.
After installation, the impression is bright! Super bright! It's super bright!
It also reduces power consumption, which is essential for TRAIL vehicles that turn the Cell many times on forest roads.
It may be due to the brightness, but it seems as if the light is diffusely reflected upward by the Fender.
I think it may be due to the Decal, but there is more light in the upward direction, which cannot be managed by optical axis adjustment.
Not enough to adversely affect oncoming traffic, but enough to require a little care in making adjustments after installation.
View detail
Outstanding brightness
I don't think you can go wrong with any of the Sphere Light series.
Again, I am satisfied.
View detail
Fanless LED
This LED is perfect for vehicles without the space behind the headlight, which is unique to off-road vehicles.
Almost the same size as OEMHalogen, so it can be installed without any problems.
View detail
It was an initial defect.
When I tried to install it immediately after receiving it, it was blinking ChicaChica and I could not use it. I thought my motorcycle was bad, so I ordered another product from Amazon and installed it and it lit up without incident. I would like to return it as soon as possible, but I have not received any response from Webig! Amazon is much more reliable. View detail
They say it's good if it lasts 5 years.
After five years, it broke. When I removed it, the yellow-colored luminous body was shattered and the base was burnt to brown. The light suddenly faded and became like a miniature light bulb and disappeared. I was surprised because I happened to be watching it. It would have been extremely scary if I had been driving at night.
When I bought it, the yellow colored tip was not square and the corners looked peeled off in places. I asked the ManufacturerStaff if the Large tip was sturdy, but they said it was fine, so I had it installed.
Well, it would be impossible because it looks like the LED light-emitting base part is burnt out.
As for the product review, at 6000k.
It is not brighter than OEM, but the color is White, so some scenes actually look darker. It is still not as good as the most powerful HeadlightHID, but it looks better than the OEM Halogen when compared to rural roads and other places without streetlights. 。
However, in urban, city, suburban, and highway areas where there are some lights, the white LEDs are covered by the lights and it is difficult to tell whether the light is illuminating or not.
If the Type is one light on low and two lights on high, I would recommend changing the color temperature with low high.
This time I did the work myself, but when I first bought it, I was told that it would wait 20,000 hours or 10 years if it didn't break, but in fact it was 5 years, so I felt like I lost money, but that seems to be the way it is.
It is good that they are cheaper now because of the New Model, but I wish they would have stopped reducing the warranty to 2 years if they continue to claim that they can be used for a long time.
Now, how to do the work
This time, I performed the work myself, copying the way SphereLight's ManufacturerStaff actually did it on my Motorcycle.
As mentioned in the postscript, the way this Rubber fits (How to put it out?) If this is the case, the heat sink portion will be buried in the rubber, so I am concerned about whether the heat dissipation will be large enough to withstand the heat.
Turn the round cover of the OEM Headlight unit counterclockwise about 1 cm to remove it.
Remove the valve spring and remove the light valve.
Remove the Attachment from the Valve of the product and insert the removed Attachment into the place where the Headlight Bulb was inserted, with the four notches facing backward, and fasten it with the Spring.
At this point, you should install the Valve once in the Attachment and remember the feeling of pushing and turning it to install.
Attach the supplied CouplerConnector to the product as described in B of the Instruction Manual.
Connectors on the body side and the Light side are connected.
...At this point, conduct a lighting test.
The space inside the Headlight unit is quite large when you put your finger inside, so leave about 15cm of Wiring and put all Connectors and Controllers inside the Unit. (I put almost all of them in Space under Unit)
Note that if the wiring connected to the light is about 10 cm, the light valve will stick when the cover is attached and will not be able to be pierced.
If the controller rattles inside the headlight unit, use the Tie Band to hold the controller in place. I don't do it.
Once this is done, it is time to install the rubber cover, which is the most difficult part.
It takes several hours at worst, and although it is easy to install if the Rubber is heated considerably, it is not recommended because deformation is a concern.
The difficulty level increases because everything is put into the Unit.
Push the outer frame of the Rubber cover into the Unit.
At that time, the side that is folded should be toward the rear of the vehicle.
When you push it in, there are three indentations where the OEM's round cover fits.
Make sure three Folds are outside the Unit, then install the LED Bulb.
(Note that if you push the Rubber as hard as you can, only one Fold will come out backward.)
(The outer frame of the rubber cover of the type after the warranty period of 2 years is larger than that of the type before that, so it should be installed in a larger size.)
LED Bulb is perpendicular to the ground when installed.:Pair (for Left and Right) to be facing the
If the remaining wiring seems long, push it in a little at a time.
The above work was completed without making any cuts.
ManufacturerStaff had done this and it was a work procedure that worked fine.
However, if the rubber is pushed out this far, the heat sink will be buried in the rubber, so I wonder if the heat dissipation is Large sturdy. I wonder,
I had done it this way before, so I copied it as it was.
View detail
Will it pass inspection?
I installed these on a 2016 MT-07. After installation, I had the optical axis adjusted by a Tester shop and they told me that the light intensity is OK but the light has spread to the side, so it will pass inspection 50-50. By the way, before I installed this, I had passed the inspection 3 times with the first generation LED Ribbon from SYGN HOUSE. The brightness is perfect, but since the next car inspection is a year away, I'm not satisfied with the evaluation until then. View detail
From Halogen to LED
The installation itself is easy, but it was very Large strange to fit it inside the Headlight.
Headlight floated and was very hard to close. I had to adjust the Wiring many times, and after pushing it in with a lot of effort, I couldn't close the Screw by myself and had to ask my family for help. I wonder if the Wiring I pushed in is Large sturdy… Spring was used as OEM.
View detail
LED
Excellent brightness, no return to Halogen View detail
Large satisfactory considering the price!
Satisfied with both brightness and visibility.
In actual use, I prefer the 4500K recommendation.
View detail
Sure, it's bright, but...
Used for Cub Pro (JA10).
Installation, but Controller does not fit within Light.
It will be installed outside.
It was installed under the FrontBasket.
I ran it and it does indeed brighten up.
However, there is a mysterious light on the Left. This is for oncoming cars and people.
It is thought that it will be dazzling, so I put a Tape on the Headlight.
We made it harder to get out.
The brightness is good, but the light scatters, so that was Minus.
Caution should be exercised by those who are concerned about oncoming illusions.
View detail
White is perfect.
Scooter used by my father, who is about to turn 60, since September 2020. [God of thunder Gu Alpha But, in January 2024, it became impossible to turn on the light at the actual mileage of 6,273 km.
It was purchased at a certain Denshin Site, but it had completed 2 years of warranty, so I decided to buy it quickly.
However, I don't want to use LED bulbs of unknown origin.
As I said, Sphere Light took care of us again.
Compared to this EntryType, God of thunder Gu Alpha, the difference is more than 2,000 yen in price, and appearance (Heat Radiation Fin?) is different from Large.
Attaching to the scooter requires no large amount of labor, and anyone with dexterity and fingertips can replace it.
The color emission is 6000Kelvin White color. Once you know this color, you can no longer go back to the bare bulb-like color of the OEMH4 Valve.
(It's a toss-up as to which one looks better farther at night due to differences in power consumption and light quality.)
One year warranty for about 2,800 yen. As expected from Sphere Light.
Please keep it as long as possible.
View detail
I think it's bright.
I can't compare with OEM headlight because I don't drive at night and I changed to this LED immediately after I got the car. I don't know if it will pass the inspection or not now. As for the installation, I could not install the Waterproof Cover on my motorcycle because the overall length is longer than the OEMValve. View detail
Easy to convert to LED!
The headlight on my ZrX1200 DAEG was dark, so I wanted to convert it to LED, but I was skeptical about how bright it would be, so I couldn't get my hands on it!
It is not dramatically brighter, but it seems brighter than the Halogen bulb. The Orange Valve I had been using was old-fashioned, so I think it was somewhat AntiAging. I think the darkness has been improved from the feeling of running at night.
View detail
The brightness as well as the 3-year warranty were deciding factors in my purchase.
BANDIT1200Initial Model for Hi (HB3) to be purchased on or about September 2022.
Lo had already installed God of thunder Gu3, and for Hi we installed God of thunder Gu2, which was less expensive.
Compared to Lo, Hi was only a little brighter when illuminated in the distance, as an actual driving impression.
But when illuminated up close, it was a far cry from Halogen.
Please refer to the video.
It is a safe and reliable product that passes the vehicle inspection.
The 3-year warranty was also a deciding factor in my purchase.
It's been over a year since I bought it and no problems (although the mileage is less than 1000 km...).
View detail
Needless to say, considerably brighter than Halogen
Purchased around last September for LoBeam (HB4) of SEA BASS BANDIT1200Initial Model.
For HB4, the two choices were this product or RIZING2, also by Sphere Light.
LoBeam is always on, so we installed the latest version.
I was worried about whether the vehicle would pass inspection because of the ProjectorLamp, but I am relieved to hear that it passed without any problems.
The brightness is also much brighter than Halogen and I am satisfied with the results.
I am running TEST for reference.
View detail
LED for Sphere LightMotorcycle
It is bright and nice for the price. I would buy it again next time. View detail
Small work is required for installation.
We replaced the headlight with LED to cover the power consumption of electrical components in winter. I have not driven at night yet, so I do not know how much brighter the headlight is, but I could feel that it is much brighter during the daytime. The optical axis also seems to be large and strong.
The only thing to note is that the Controller and Coupler will not fit in the Bonneville 120 Headlight case.
I installed it on the Headlight BracketReverse side.
View detail
Both High low of Type 2 GSX1300R HAYABUSA are replaced.
Previous Spec. is NORMAL for High beam.
Low beam is HID55W made by 88House.
The high beam was too dark to pass the inspection, so we replaced both the high and low beams with LEDs.
result
The high beam passed the inspection with ease, but the low beam is too dark to drive at night.
I think it is brighter than NORMAL, but I felt it was too dark for my experience with HID 55W.
In the near future, we will switch back to HID only for Low beam.
View detail