Reviews
Used for Tank on Ninja1000sx
[How is it used?
The tank of the Ninja 1000sx is wide, so when touring long distances, the sitting position is inevitably shifted to the front. When I was riding Z650ABS, I used the same manufacturer's standard (black), but I was concerned about the floating of the glue, so I changed to SILICON this time.
Was the one you received as per Image?
Color is Color:It is so close to Gray that when attached to Black Painting, it looks like it is floating. It is not so bad once you get used to it, but I would have preferred a stronger black look.
How was your experience with it?
Functionality is fine. It has a firm knee grip.
[Points to note]
The location of the paste is unknown and must be confirmed on the ManufacturerHP.
How did it compare to other products?
I feel that the texture is not as good as the company's Standard, but it is supple and does not seem to peel easily.
Requests, etc. to Manufacturer
I noticed a lot of White paper dust on the product when I opened the product. Perhaps dust from clothes will also be a concern in the future.
View detail
It's a Universal Product, so there's no choice.
I would like to see a little more length, but the minimum area is covered, so that's good.
Even if applied properly, Air is hard to remain and has sufficient adhesive strength, but the color is not colorless, so Black may be less stressful.
View detail
Fits: TRIUMPH SPEED TRIPLE 1200 RR
Cheap ????.
The color may be translucent or Quantity:Pair (for Left and Right) The quality was disappointing for the difference in size and delivery time.
If you can afford it, buy it at a special price, it is a good one to prevent slipping.
View detail
Quality is better with Stomp Grip.
I had installed the Stomp Grip but the seat on the side cowl side was too small and didn't hit my knee area, so I left the Stomp Grip on the tank side as is and replaced it with the EasyGrip on the side cowl side. As other reviewers have said, the EasyGrip is a large size, and I am satisfied with its functionality, but the EasyGrip looks like it is cut out from a large Seat to fit the car model, but the StompGrip has no warts on the edges and is molded one by one, so the texture and appearance are parenthesis. The StompGrip has no warts on the edges and is molded one by one. It's a choice between functionality and appearance. View detail
Reliable EasyGrip
We used EasyGrip about 3-4 years ago when we switched from StompGrip.
Since then, EasyGrip has been my choice, and I personally think that EVOType has better gripping power than Stomp.
Recommended for people who drive on circuits and mountain passes, and for sports drivers.
View detail
Prices are high for dedicated products.
[How is it used?
I used it for about 3 months. I am satisfied with the expected Grip effect.
Was the one you received as per Image?
I was torn between the EVO shape and the PRO shape, but I decided on the PRO one based on other people's impressions. I wanted to make the bumps less noticeable, and I also wanted to get the color of the car body. [Color] I chose Clear. A photo of the entire car body is attached for reference.
Was the installation difficult?
There may be some difficulty depending on the Tank shape of the vehicle. In my case, the tank shape has no gouges and is straightforward, so it was relatively easy. After temporarily attaching with paper tape, I peeled off half of the backing paper from the edge and patiently attached the tape. The first one was just a little off, but the second one seemed to grab the hang. The air bubbles definitely get in, but I think you can make it better by applying it little by little and getting used to it over and over again with your hands. (It will gap, so you have to pull it in the right direction little by little! Also, a rubber roller would be nice).
What is your experience and what is your disappointment?
Knee grip is easy. I am satisfied on that point, but there are two minus points:1. it seems to be a little aggressive on Jeans, and the fabric is a little fuzzy; 2. the price is too high; and 3.
A word to the manufacturer.
Please give me a few canned Sizes that I can use in Universal. Cut yourself.
View detail
To assist with knee grip
Purchase EVO.
The pad itself is soft but a little thick, and if left as it is, it does not fit the tank shape and floats in some places.
If heated with a heat gun, it becomes even softer, making it easier to apply to curved surfaces.
Since the foot usually hits only the lower part of the tank, I wonder if it would be effective in situations where the tank is held.
View detail
Performance is OK Red to [Color] Clear fails
For PANIGALE V2 [Color] I put up Clear, but the double-sided tape of the pad does not follow the concave part of the tank curvature, so the tape sags inside rather than airs out, and the appearance is a failure. The problem is that you can see through it.
I plan to change to Black because it is fine in terms of performance and the Pad surface is not sagging.
View detail
I was mistaken.
It is not a pad, but an anti-scratch film. The length is long enough from Seat to Fuel Cap.
The sprayer comes with solvent, so it can be diluted with water and applied while aligning the position.
A spatula is also included so that the product can be adhered to while being squeezed.
If you scrub too hard, it will probably tear, and the solvent is too thick if you just add water to a misting sprayer, so you should adjust the amount.
If you have used Wet for Film and Sticker, it is no problem, but you can also use direct paste, if you prefer.
View detail
Fits: YAMAHA XJR 1300
To Knee grip
I chose EasyGrip, but it didn't have enough grip. I am a good flyer, so I think it would be better to choose a product with a higher Grip for such a person. View detail
Fits: KAWASAKI Ninja250, KAWASAKI Ninja400
I want to put it on Tank.
Was the one you received as per Image?
Both cards have a Stain-like aftertaste on the Pad, and evo would have been better.
How was your experience with it?
In NINJA, it is not applied to the tank side, so the only area that is hit is the knee, which is a little short on hold.
[Points to note]
It is advisable to check carefully before purchasing which position on the Motorcycle you will be affixing it to.
Overall, it is a solid product and I would purchase a Tank Part pad if available.
View detail
Fits: SUZUKI GSX-R600 , SUZUKI GSX-R750
Buy PRO
Used on GSX-R750. I washed the car, wiped it clean, degreased it, and warmed up the product with Dryer before trying to apply it, but it didn't warm up very well, so I put a cloth over it and warmed it up with Iron and it warmed up right away.
It seems to be quite easy to get air bubbles. I put it on and left it for about 2 days without riding it, but the paste in the corner was not going on weakly and was peeling off. I have tried warming it up again and putting pressure on it, but it is not sticking.
Compared to stomp, it has a Hold feeling and feels less slippery.
View detail
Installation is in accordance with car film
The spray is included in the package and it is very easy to install. It has just been installed and is distorted due to moisture in the gaps, but once it dries, I think it will be large and sturdy. View detail
As expected, but I think it's too expensive.
Knee grips are excellent and easy to do, and there is no gapping after installation, but they are too expensive, no matter how reliable the product is. View detail
Simple Tank Pad
I purchased and attached it to prevent scratches on Tank.
Since it is a clear type, it will look bad if the air is not properly removed during application.
It consists of two pieces with Logo, but I don't know why it is made in two parts.
The area is small, so it may not protect the tank from scratches when riding heavily.
View detail
It's cuttable, so you can make it the way you want it.
I like the fact that I can cut it myself, so I can make it the way I like it.
However, it is difficult to cut it beautifully! You have to use a sharp knife to cut it.
View detail
[Color] Replaced Clear with Black.
It was smooth and hard to get a knee grip. [Color] I purchased Clear.
The way I ride, I did not need it on the Tank and only put it on the Side cowl.
However [Color] I did not like the color of Clear.
I was satisfied with the functionality of the product, so I purchased Black and reattached it.
I peeled it off after about 3 months and warmed it up with Dryer and it peeled off cleanly with no adhesive residue.
Even the slightest air purchase is less noticeable in Black.
Now I am happy with the look and functionality.
View detail
Knee grip
Black or. [Color] I wasn't sure if I should go with Clear. [Color] I thought Clear would look better, so I decided to go with it. When applying it, I peeled off the Seal a little at a time, and while holding the air in, I applied it, but it was quite easy for air to accumulate and I had a hard time. There is another sheet to put under the tank, but I don't think it is necessary. I put it on for the time being and did a test run, and the tank pad is supporting me well. I don't think that the smaller ones below will be useful. I think I will remove it in time. The price is quite expensive, but I thought Tank Pad alone is enough. View detail
I'd say it's a decent grip.
On the FAZER, I put it on the cover of the frame where the knee touches rather than the tank. I did a little bit of tweaking by myself, so it turned out a little awkward, but it doesn't bother me. It's difficult to make it look good, but I think it's better to use a cut product for each model.:It's a gray color, so it doesn't stand out. The grip is not so good. View detail
Difficult to process, but the grip is perfect.
This is Type, which you cut and paste by yourself.
As for processing.
It's difficult, so you might want to practice a few times with the parts you don't need. (I should have). 。
I used the Cutter and Scissors together, but the circle is thicker than the other two.
It is difficult to cut straight because of the repetition of areas where the blade can easily enter and areas where it cannot.
I would like to have some kind of cutting machine to position and cut them all at once.
Also, keep replacing Cutter blades with new ones.
As for pasting.
Of course, it's a matter of friction and unevenness.
It's hard to rub it with your fingers after applying it to make it stick. (Eliminate air bubbles) It's hard to do.
If you make a small mistake while applying it, you can reapply it, so apply it loosely.
It is a good idea to keep them close together in a certain place.
It may be similar to Decal paste.
In conclusion, Black is good.
There is no problem at all with peeling. It will be quite large and strange when you peel it off.
As for the texture.
I think it's just like the image. It's not particularly good or bad. It's good enough.
However, I made the mistake of buying the transparent Seat. It should have been Black, which would have made the bubbles invisible.
(I thought that Black would look like White as it deteriorated.)
Transparent Seat is suitable for White and Color:I think it is a light color like Gray.
Knee grip is necessary for correct riding form, and
Since you need to make sure to Form and drive safely even in Touring and city driving.
I would like to see Manufacturer sell a special product for all models that can be called a Sports car with Option.
Lastly, the seat size is listed on the Page of the product description.
In fact, it comes with two Seats of that size.
I bought it because I knew about it in advance from my personal Net information.
If I hadn't known about it, I wouldn't have bought it.
I think it would be better to put this information on the website.
Evaluation items "Use Situation." is between Touring and Circuit for convenience. It is valid for everyone.
View detail