Reviews
Refreshing around the Rear
We chose this one because it was Reasonable price than other Fender Eliminator Kit.
First of all, when I first received the product, the holes in the Plate and Bracket did not match, and when I inquired about it, I was told that a different model had been included.
When I actually installed it, I had a hard time removing the OEMFender first.
There is no instruction manual, so I had to loosen the bolt and remove the parts, but there might have been some parts that I didn't have to remove.
The space under the Seat is narrow, so the Coupler for the lights is quite difficult to pull out.
Also, I used a small-sized MONKEY Wrench because the included nut was a size I don't usually use, but I think it would be more efficient to prepare a socket that fits the size.
As for the License Plate Light, I did not want to cut the OEM harness, so I purchased a Coupler that fits there separately and crimped the Bullet Terminal to extend the Cable, but the wiring of the attached License Plate Light is too thin. But the wiring of the attached License Plate Light is too thin, so be careful not to break the cable.
Colgate Tube was used for the wiring path and fixed to the Fender EliminatorBody with inHemp palmac.
The key cylinder of the Seat lock is screwed into the inside of the car body from the side. (I can't help but feel that the Seat lock release has become harder)
Speaking of the seat lock, the OEM dust-proof cover cannot be used, and the keyhole is exposed, so I think countermeasures are necessary.
I process thin rubber sheet and attach it with strong magic tape to make it removable and to prevent mud and dust from entering. (I've only run it a few times, but so far the keyhole is Large strong)
It took a lot of time to install the new product due to various modifications, etc., but it is a recommendation because it looks like a reflection.
(Although this will make the water splashing up behind the Fender a little worse.)
View detail
Be careful of misconnections
[How is it used?
Installed on a 2022 MT-09 SP.
The OEMFender didn't look good and even if it did, it would roll up mud and dirt, so I decided to replace it with a Fender Eliminator.
Was the one you received as per Image?
It looked better than it does in the image, but it takes Sense to hide Wiring nicely.
I don't have that much Sense so if you look closely, it's rough.
Was the installation difficult?
1.Needs to be completely assembled from RoseRose state.
2.The instruction manual is in English version.
3.Overtorque needs attention because of tightening by Bolt of plastic parts.
4.Wiring for License plate needs wiring processing
The four elements of the system make it a little difficult for a novice maintenance person to install.
How was your experience with it?
I thought it was worthwhile to have it installed because it looks Refreshing compared to the OEM parts. Also, the small parts have the Manufacturer's logo, which I personally think is GOOD.
[Included Parts:were they on?
Three instruction manuals and, although not used this time, a mounting bracket compatible with external blinkers are also included.
[Was there anything that disappointed you?
As is often the case with MT-09 external Fenders, when replacing the OEM Product, the key slot for removing the Seat is exposed and dirt gets under the Seat. This product still has the plate, so I think it is relatively better, but it would have been nice if the lid of the OEM Product could have been used in the same structure.
[Availability and clarity of the Instruction Manual
Note that, because this is an overseas manufacturer's product, it is different from JapanManufacturer's product and is not written very carefully. Also, the assembly method varies slightly depending on the shape of the license plate in each country, so it is necessary to assemble the product while confirming the shape of the license plate.
View detail
Better looking than expected.
First of all, it is light anyway.
I would say it is less than half that of OEMs.
Installation is also by pon. It's as easy as pie.
However, it is thinner than the OEM, or it rattled when attached as is.
I put in Spacer and it's ok for now.
I will try various Spacer Materials. Let's start with pon.
View detail
looks quite eye-catching
I ordered Lightech tank pad to replace old Progrip tank pad on my Suzuki Hayabusa. The Lightech tank pad is easy to fit onto the fuel tank, stylish one-point, looks quite eye-catching. However the Lightech tank pad is much thinner than the old Progrip. View detail
Unobtrusive and good.
I have it attached to a Norton type aluminum tank, and I like the fact that it is transparent and inconspicuous. View detail
Fits: APRILIA RS 660, APRILIA TUONO 660, APRILIA RSV4 FACTORY
Fender Eliminator that is not too short
For installation, the license lamp requires Wiring, and the OEMConnector was diverted.
Since Blinker is an Other Brand Product, Puch's BlinkerCable was purchased separately.
It looks a little long, but it is natural if you look at it as a whole, and I chose it to prevent mud splashes and to install a side bag, so this looks just right.
View detail
Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10RR
sitting on the floor grasping one's knees (as in a gym class)
Was the one you received as per Image?
The shape was exactly what I expected and the location and Size were Exactly more than I expected. I thought there would be a little more laxity in some areas.
The weight was much lighter than expected.
Was the installation difficult?
Easy.
How was your experience with it?
The installation position is more rearward than other products. It may be different for different tastes.
The angle of the License Plate is variable, but the angles of the License Plate Light and Reflective Plate are also variable.
Well, I'm glad to hear that your butt is looking good.
[Included Parts:were they on?
It is very tight with no leaks. I have an extra Bracket from Rai TECfor Blinker, but I would like to buy Blinker when I feel like it.
[Was there anything that disappointed you?
I wish the Wiring of License Plate Light was a little longer.
[With or without Instruction Manual
I can't read Italian.
[Notes]
One of the couplers (White) of the OEM License Lamp will remain on the OEMFender side, so some modification is required for wiring.
I cut and brought the OEMFender side and processed the WiringBullet Terminal because it was troublesome.
Blinker does not require processing because OEM is attached to Beauty.
The fixing part on the nut side of the reflective plate is plastic, so care must be taken when tightening it.
Point and hang of installation
The Lai TECLicense Plate Light has a License Plate Light (White line) and a Stop-lamp (Red line).
OEM side Stop-lamp (Blue wire) Tail lamp (Red wire).
There is plenty of room here, so the Wiring Connector is the quickest way to get into Wiring.
Wiring together in the back is a Daiso product (see photo).
View detail
Rear brake air Guide
The name of this item is Sprocket Cover, but the OEM part name is Rear brake Air Guide.
The function would be to cool the Rear brake.
I had to replace it because it was dirty and white and it didn't look good.
Front Fender was also changed to Carbon for better balance.
All that remains is to replace the Rear Fender.
The accuracy was poor for its high price, and installation required forceful hole alignment.
Also, the packaging was messy.
Washer is required to use the original Bolt as it is different thickness from OEM.
View detail
Fits: APRILIA RS 660, APRILIA TUONO 660, APRILIA RSV4 FACTORY
Aprilia RS660Fender Eliminator
The product is a matte black color and is of excellent quality.
The product details stated that the License Plate is also compatible with the Japanese standard Plate, so I decided to install a Rai TEC License Plate with Reflector on the RS660. (Complete) selected.
View detail
Fits: KAWASAKI NINJA 250, KAWASAKI NINJA 400, KAWASAKI Z400
Great product
The Fender Eliminator is great for achieving a tidy and short tail. The product is well made and fit for the bike. The only problem is that it it a little bit long for the licence plate of Hong Kong. Otherwise it is perfect. Recommend to anyone who want a clean shape of bike. View detail
Good enough for Suspension mudguards.
When I go through a puddle of water, even a little bit, the Rear Suspension gets dirty, so I was looking for a good fender and came across this one.
Installation was easy and SMART without having to remove the wheels as long as you have a long driver.
I think it is functionally effective as a suspension mudguard, but…Well, it is not very large, so if you run in the rain, your back will probably be sloppy. (Lol)
Instead, the Design is Refreshing, and I like it.
View detail
Fits: HONDA CB125R, HONDA CB250R, HONDA CB150R, HONDA CB300R, HONDA CB150R, HONDA CB300R
Satisfied
As for the installation, the existing 4-point Bolt is long enough to install on the vehicle, so I installed a shorter Bolt instead.
Other than that, it came with no other processing.
The Wiring process needs a little work to make it less noticeable.
Unlike the Fender Eliminator, which is too short, I think it provides some mudguards.
I like the look and feel of Balance quite well.
View detail
Fits: TRIUMPH DAYTONA 675 R, TRIUMPH DAYTONA675, TRIUMPH STREET TRIPLE, TRIUMPH STREET TRIPLE R, TRIUMPH STREET TRIPLE, TRIUMPH STREET TRIPLE
Just the way I wanted it!
First, it's not the cherry on the webike.
The BackStyle changes completely and the angle adjustment is also free, and I am ok with it. Maybe!
However, there is a need for a little ingenuity in the details, such as a bite of Rubber or hiding Wiring.
Mud splashing is not limited to this motorcycle; it's a natural part of the rear end of the car when touring. It explodes, rocks, etc., but …
There is no fading or deterioration after a year.
View detail
Expected to reduce dirt on Rear suspension.
GSX - R1000L 7 - includes Rear (Inner) Fender, Mud Guard is not installed,
Because the surroundings of Rear suspension become soiled, I was looking for a countermeasure item.
We also examined other Manufacturer's, but the delivery date to be determined (3 months or more) or,
I chose this Lightech product because its shape does not suit my taste.
By the way it is dealt with by web! Ke but the delivery date is too long (1 and a half months) Because
I bought it from abroad. It arrived in less than 3 weeks.
About the product - - -
There is no installation Screw, instruction manual, installation explanation on it that came from overseas,
Only Fender has arrived.
(If you purchase with web! ke, the authorized distributor will be doing it for Japan.
I think that it is impossible to buy the same thing in Japan - - - )
I installed it for myself about the installation.
If you get confused about how to buy the same thing or buy it before you buy it
I will answer if you can listen using Message function.
I hate being imitated by an indefinite number (Lol)
As for accuracy, it has a good shape to fit perfectly with the reinforcement part of Swing Arm.
I also felt that this Manufacturer 's thing was "usable".
Even the mounting method even if the Manufacturer designation is ordinarily there will be more points.
I think that the shape is a little small, is not it?. Just absolutely better than nothing,
Large is too much I wish to work so I wonder if this is better - - -.
Strength is sufficient. I confirmed the making of each part before installing, but there is no anxiety at all.
Since the traveling after installation is still small, the reduction of dirt around Rear suspension
It is not realized but it will be better - - -
View detail