Reviews
Dismounting Caution
Fitted to prevent moisture and for aesthetic purposes.
It has the same glossy finish as the Frame, so it has a good sense of unity.
As noted in the Instruction Manual, care should be taken when removing it because it is made of plastic and the nails are thin.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-6R
I installed it for another car model.
I installed the ZX-12R with the Handlebar Up Type in TouringSpec. The mounting hole was made a long hole and the point where it contacts Napoleon-on-Mirror was shaved off. At first, the front camera was fixed under the ram air duct, but it felt uncomfortable, so we purchased a different model this time with the assumption that it would be modified. The size of the bracket is too large to be noticeable, but I personally like the design. The camera is made in China, so the camera mounting holes were also modified.
Well, it's like Parenthesis is good (laughs), it's self-satisfying.
View detail
Effect of Lowdown Seat?
Thoughts on the Ninja1000 2015
Seat Cover
The design will be different from the 2015 Seat Cover, so those who are concerned about that should think about it. However, unless you get close to Motorcycle, you can't tell, and once you straddle it, of course, you can't tell.
decreasing the value of a device (e.g. DC/DC)
The top of the seat is designed to be pulled out, so the legs are spread out, and I think it is 1cm down when I straddle it. I think it is 1cm down, but even with this 1cm, I could buy a sense of security that the seat would be extremely large. It is only 1cm, but that is 1cm.
If you are still concerned, you can install a Lowdown Link. There is a lot of discussion about lowdown on the Net, and I have ordered a Lowdown Link from Len Barrel Motorcycle. (Ninja 1000, both feet sticking to the ground) I did not know what to expect from a normal Touring ride on a Do you ride your own motorcycle on the circuit? The feeling of safety with both feet on the ground is irreplaceable.
View detail
It's a pain in the butt, but the bottom line is get used to it.
Footing has improved.
Pain in the butt depends on how you ride and what you're used to.
It was a good personal purchase, but a bit expensive.
View detail
Further Lowdown
I am about 170cm tall. Even with the standard ride height, I can reach the ground with my heels slightly raised, but I was worried that I might feel dizzy when driving at very low speeds due to the high center of gravity of the vehicle, so I used Trickster's Lowdown Link. I used Trickster's Lowdown Link. It was low enough, but I wanted to lower it a little more, so I replaced it with K’s Style's Lowdown Link.
The material seems to be Steel with Black paint, so I would have preferred Stainless Steel or Duralumin Anodized Treatment if possible.
It must be used with the company's Short Stand recommended by Manufacturer.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-6R
2016 ZX-6R
It can be installed on the 2016 ZX-6R as well, although it is listed for 2021 and up. I was able to install it on a 2016 ZX-6R. View detail
For peace of mind.
I bought this bike along with the Short Stand to improve the footing. I am not confident about the installation so I had it installed at the shop where I bought the bike.
With the Low seat, the footing has improved until the soles of the toes manage to stick.
The price is quite high, but it is a necessary investment for safety and security.
View detail
Fits: KAWASAKI Z800, KAWASAKI Z1000, KAWASAKI Z1000 ZRT00B-, KAWASAKI Versys 1000, KAWASAKI Ninja 1000
Custom Required
It is one of the first things to be purchased and installed when purchasing a motorcycle.
Essential for protecting and curing the Radiator core.
If it is not installed, the Core will be crushed by small stones, etc., or the Core will be easily damaged when cleaning the attached insects, etc., which will weaken the function of the Radiator.
It's an expensive purchase, but I installed it because I needed it for peace of mind.
This product is easy to clean, no snagging when cleaning and has a nice feel to it.
View detail
I am satisfied.
I'm short (short legs) and in the OEM I could barely touch the ground with both toes.
This Low seat seems to process the same etc. goods as OEMSeat, and the surface skin is the same, so I bought it as one way of Lowdown.
The back of both toes came to be attached together with Lowdown Link Plate -30mm though it was -20mm in the catalogue figure.
Both sides of the seat are rounded, while the corners of the OEMSeat are standing up, and the legs are facing down a little to improve the footing.
I ride a lot of long touring, but I don't feel any damage to my butt until about 3 or 4 hours.
The price is quite a bit, but the Seat replacement was worth it.
View detail
Top case for convenience ???
Even though it's a dedicated product, it's expensive.
If it had been cheaper, I would have purchased it earlier.
View detail
My footing has improved.
I'm 5'7" and I'm able to keep both feet on the ground.
It's very easy to get out of the parking lot because you can step over and back down.
I installed it myself, but in the case of SE, I removed the Center Stand (Also Right Sidefootpeg) Also, you need to hang the car body from the top. It was quite Large strange. When you put the PenetratingBolt on the front side, if you insert it from the opposite side, you don't have to remove the Center Stand, so if you have a possibility to put it back, please do it at your own risk. If you want to put it back, please do it at your own risk.
View detail
New design, new personality.
I installed it on a 2020 Ninja1000SX.
I stripped the Decal of Green of OEM and renewed the Image.
This vehicle met two or three of the same vehicles at the Touring destination.
It wasn't unique, so I changed it a month after I bought my new car.
When you peel off the existing Decal with Dryer while heating it, you can install it.
It comes off beautifully. The position of the existing tape in advance is
If you can understand it, you can restore it to the same position as the OEM.
(Also, Rear had a sticker as an added bonus, which the OEM doesn't have.)
Even if you work slowly and carefully, three hours is enough for one person to do it.
Wheel rims are also available in red 10? widths (5? widths in green for the OEM) and can be purchased separately.
It's all in red.
This is a mass-produced vehicle and is a great choice for those who want to show off their personality.
View detail
Fits: KAWASAKI Ninja1000SX, KAWASAKI Ninja400, KAWASAKI Ninja1000, KAWASAKI Ninja650, KAWASAKI Ninja400R, KAWASAKI Ninja650R
It was surprisingly uncomfortable. (Lol)
We chose the K's Style simple shape from among the few Mirror Hole covers available.
The product is Material:The body of DURACON has a simple construction with a female thread and a bolt connection.
However, the body is still thick and heavy due to the bolt connection structure.
Well, it's solid, to put it nicely.
And this time we'll do a little bit of work before we do the installation.
I think the thickness of SpongeSeal should be about 3-5mm.
Next, it is a simple job to remove the Mirror and cover it with this Mirror Hole Cover.
And the meter cover must be removed in order to access the Bolt that is attached to the Mirror.
However, since the Ninja1000 17MODEL, it is not easy to remove the meter cover.
In addition to removing the side cowl, you have to remove the Windscreen, Cover in the Upper Cowl, and Meter to remove the meter cover.
I've had experience with multiple Full CowlMotorcycles, including the original Ninja 1000, and I don't understand the structure when it comes to maintainability.
If the meter cover is removed, afterwards I think that it is already Large sturdy, but this time there is no work space.
Once the bolts are removed, the installation is done in reverse order.
Just to be safe, you can apply an anti-loosening agent to the bolts.
Fitting, there is no interference, no gaps, and no problems after installation, although delicate alignment is required.
At the end of the day, it takes a lot of work (or labor) to convert a Handle mirror to a mirror, but once you do it, the repair costs are low if the mirror is damaged by a fall, according to Merit. (Lol)
View detail
It is indeed an Exclusive Design product and there is no question about it
ninja1000 (19 years) I installed it in
There were several similar products, some of which were pricey:the Pannier case As I have already put Bracket on it, the choice is SHAD's or this? So I decided on k‘s-style's
The rigidity is different when viewed in comparison with the video and Net images Even after putting it on, it's still very solid
View detail
Large satisfactory product if you can meditate on the price
I installed it on my 2019 ninja 1000
As a rear carrier, the price is quite high category, but the side panier of OEM When it comes to using the Top case as well as the case, there was no other choice but this product!
If you want to use TriplePannier on your Ninja1000, this is a must have item The load capacity goes up and I am satisfied with Large
View detail
I bought it after a long time Large satisfied with the effect
When planning a long touring trip, I considered purchasing a low rebound Seat to relieve my buttocks pain I also purchased this product in the hope that it would improve my comfort level by improving my footing
The effect of the low rebound was also demonstrated and butt pain was reduced I could feel the effect on my legs more than the numbers
I haven't been able to earthquake-poorly buy it, but now I'm very pleased with it
View detail
Improved footing! But I'm not sure how well it works with Lowdown
I installed it in Z900RS Cafe
CAFE Seats have a 2 cm high seat compared to the Muji It's only 2cm, but it affects the landing
I used to use the Muji Seat, but it's -1 cm more than the Muji OEMSeat To be honest, I didn't feel much of a difference
However, it doesn't feel uncomfortable to ride without Anko The effect of Lowdown Sponge or the buttocks are not painful
Because of the machining on the driver's side only (anchor removal), there will be a big gap between the driver's side and the Tandem side I thought it was unsuitable for Tandem
It looks good, but it's for people who don't Tandem
View detail
It is an essential item.
I bought this because I use my phone with Navigation Installation was a bit of a challenge The product had a lot of scratches as all the parts were in one bag
Quantity:Pair (for Left and Right) I feel that the rigidity has increased because it connects the Handlebar of
View detail
Visibility has improved
installed on a ninja1000 (2017) MODEL. the OEMMirror has a width Quite a bit of traffic, etc., to get by
I was running with one of the mirrors closed at the time of I replaced it with a typeMirror and it's very
It is now easier to drive The visibility is good and I am happy with it
PS. It's a bit of a hassle to install the Cowletc. off Let's
View detail
Impressions after driving
Today, I tried Touring about 100 kilometers, I think the feet have improved a little better?
It was about
Low Repulsion Processing (Probably pulled out and low repulsion Seat) So I thought it was softer
Other than hard (Because Seat thickness is getting thin?
But the bottom part of the buttocks is flat, the body pressure of the buttocks is dispersed as a whole, it may be harder to get tired than Normal seat
View detail