Reviews
Silencer gasket
I used it when I installed T2RACING's Silencer on Hulk's Chamber, and although the Silencer itself was confirmed to fit, the three M6 mounting pitches were different and the hole on the Flange side needed to be widened by about 0.5mm.
Gasket also naturally has a different Pitch and requires a wider hole.
Some modification may be necessary when using for chambers other than T2RACING.
It functions fine and has no exhaust leaks.
View detail
Fits: HONDA NSR250R
Bar End
Bar End, Design is good, so it is replaced.
It is not bad looking.
Quantity:Pair (for Left and Right) Quantity:2pc. The price is a little expensive because it is sold as a single pc.
View detail
No need to cut and easy to use.
I purchased this for use on Seat Cowl for Race.
I used to use Rubber with Cut, but since it was Just size for Cowl, I use it as it is.
It is with Adhesive Tape, so you can put it on as it is after you buy it.
If it is not thick enough, you can use it in layers.
View detail
No Single Body sales of this packing in OEM
So far there seems to be no leakage. I wonder how long the durability will last. View detail
Looks good
RCValve and PulleyFixing Screws were getting old, so I was curious to purchase Titanium, which I have been interested in for a while.
It looks good, although it is small….
I would have no complaints if the price were lower.
View detail
Fits: HONDA NSR250R
Collaboration Separate Handlebars
There was no good one, and this product seemed to have a good design in collaboration with the manufacturer. I was excited to purchase the separate handlebars for NSR250R after repeated tests.
The black handlebar was also selected because it is the original color and the OEM is also black.
It is unclear where the original color is.
I would appreciate it if all Fixing Screws were also unified in Black.
The price is there, but the packaging is Air cap protection only.
Installed, we will see how it goes for a while.
View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
What kind of …
Torque up from bottom to top by widening the movement of RCValve, how does it feel? Installation and replacement.
It looks good in Red.
I struggled a bit with the full opening adjustment and Wire tension adjustment, but it looked good with Response? I think.
I wish there was a Clutch type like the other ones. A little expensive safety device considering the adjustment and load. (OvertorqueReleaseSystem) would be better.
View detail
Fits: HONDA NSR250R
Bar End
Only the Handlebar End was purchased and installed.
Black without much prominence, Quantity:2pc. The set purchase is somewhat pricey. The design is nice and I like it, but the color of the Fixing Screw does not match, which is oddly noticeable.
I hope you can color match and do the same Black.
View detail
appearance
It is installed to improve the appearance.
Carbon is thin and easy to install on the surface, but the hole position must be slightly modified for installation. The installation was completed without that much difficulty. Is there an individual difference? I guess there are individual differences.
I am happy with the improved appearance, but the price is a little high.
View detail
Titanium
I was wondering whether to order Blue or Black, but I ordered the simple Black because I wanted it to be less noticeable. I like the look, but the Material:It's Titaniumium, so what? It's a kind of self-satisfaction. View detail
Fits: HONDA NSR250R, HONDA NSR250R, HONDA NSR250R
Steering
I bought this for the Steering Damper installation.
It is a definite Manufacturer, but the price is high.
The thing is not bad, but the packaging is …Vinyl, unfortunately.
I don't mind the packaging if the price is low, but for a 10,000+ item.
For this price, you need better packaging.
I don't need Sticker, I want it to be cheaper.
View detail
Fits: HONDA NSR250R, HONDA NSR250R
That's not the picture
Material:I bought Titanium and the angle of the Silencer is different from the picture.
The upper silencer is almost level with the ground at the top of the rear tire, so the exit of the silencer is also facing down. So the exit of silencer is also downward.
I shouldn't have bought Level even though I'm paying high Gold.
Postscript.
I asked about the angle, but it is not a manufacturing defect or error in the product.
He said that the Silencer appears to be raised because the car in the picture uses the Rear stand. Oh, I see.... Well, it makes sense.
I'm convinced, but I'm depressed because it's actually lame.
(If so, shouldn't you change your picture? I think)
It is not a product problem, so I will modify my rating.
Let's all look at every detail in the photos!
View detail
Fits: HONDA NSR250R, HONDA NSR250R
Stainless Steel
It looks beautiful with Stainless Steel, but it is quite heavy?
It's nice to install without Bracket, but I'm a little worried about cracking under the load of vibration.
View detail
Fits: HONDA NSR250R, HONDA NSR250R
Stainless Steel
Considering the price of the new one, Material, Power up, appearance, etc., there is not much choice and this is the installation.
It looks and sounds not bad, but it is still better than Stainless Steel, if you can afford it Material:Titanium is where I want and need to install it.
View detail
Beautiful
I think the color is beautiful and the texture is good. View detail
Reinforcement Type
It seems to be good with Reinforcement Type for fixing ChamberFlange, so I repurchased and installed it.
Hook part rotation allows for hooking without straining, Material:Stainless Steel, prevention with Rubber is a nice touch.
A little too strong? A little too long? Maybe it is a little too long?
View detail
For reinforcement.
The Hook part rotates, and the Spring is strengthened, and it can be fixed good.
The vibration absorbing rubber is also nicer looking than the competition.
It may be a little tight to install.
View detail
Size, shape is cool..
Size, like shape and purchase.
Installation can also be mounted without problem using OEM's Bracket.
What I felt when I actually used it is Fender and Tire's Quantity : Pair (for Left and Right) The narrow gap (About 3 mm) Tire warmer can not roll.
I had no choice but to shave Fender and widen the gap, but do not forget that those who plan to do Warmer are processing premises.
View detail