Reviews
Cosmetic! For protection of Axle Shaft.
[How is it used?
Used at Circuit. The screw thread of Axle Shaft was almost crushed when it fell down without being attached.
Was the one you received as per Image?
Yes.
Was the installation difficult?
Just pull out the SHAFT and insert the Cup between both SIDE.
However, if you assemble the Rear Shaft without thinking about it, as has been your habit, you will have to redo the whole thing.
You might want to get into the habit of putting Cup in the beginning.
How was your experience with it?
I haven't tipped it over yet, so I can't give an imprementation, but it is solid and secure for the low price.
The resin Cover is removed, but still high enough for Shaft protection.
[Included Parts:were they on?
It had parts to accommodate M10.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If I had to say so, I would say that the length of the resin slider could be a little shorter, as it seemed to hit the ground in the Circuit.
View detail
I can guard it well.
It is used for CYGNUS X2 model.
The Axle Shaft does not interfere with the ground on Scooters because the front fork is short and the cowl sticks out in a low position.
Since I had replaced the shaft with the Chromoly Axle Shaft from Other Brand Product, I had enough room to install the Axle Shaft Slider, but I think it is important to note that the length may not be enough for the OEMAxle Shaft.
When I used the thin nut supplied by another company, I sometimes licked the screw mount of the nut when I tightened it with the specified torque, so I did not use the supplied nut this time either.
When the mount base is installed, only the slider part can be replaced without having to remove everything.
Also, I think the Axle Shaft will be less likely to rust in the rain, etc. since it is completely sealed.
Since it has a shape that seems to have a high degree of universality, I think it can be used as a Frame Slider or Exhaust Guard in addition to the Axle Shaft Slider.
View detail
Grom JC61 '15
Used for Grom JC61
I bought this for the guard of my Yamamoto racing muffler in case of falls.
The Bolt that comes with this kit or the Bolt on the Yamamoto racing muffler is not long enough, so you can use a Bolt that is 10mm longer.
If you want to add color, you need to make it longer for the color.
View detail
I don't know the effect yet.
Fortunately I haven't had any mishaps since I installed it, so I don't know if it works or not. if you can install it under the exhaust system, you can guard it perfectly. I don't think it's durable, so you may have to replace it every time you have a mishap. View detail
Installed on MAJESTYS.
UniversalAxle Slider installed. 。
I was worried that it would not be able to be installed properly because it is installed by inserting it, but it was large and strong. 。
The actual tightness of the installation is the Quantity:Pair (for Left and Right) Together, about 4.4? 。 If there is more room in the Axle Shaft, there will be no problem with installation. 。
MAJESTYS would have an extra turn and a half, so no problem.
Volume around the front is increased a little. 。
I scraped the bottom of my FrontCB400T when I was pushing and pulling the Limit near the wall, so I'm trying to prevent that!
View detail
Good
I installed it on CYGNUSX (1YP2). I crashed a little while ago and installed SP Tadao's Exhaust System pretty well.
I scratched it, and installed it just in case I had to replace the Exhaust System.
There are many screws and two colors. I don't like them sticking out too much, so I chose No Color.
I installed the exhaust pipe and Slider, there is not much room for clearance with the ground and Slider
I think I'm going to add some color to it.
I think the design is good without looking bad, but it would be even better if the price was a little lower.
View detail
Fits: YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA BWS125(BWS), YAMAHA BWS125(BWS), YAMAHA BWS125(BWS), YAMAHA BWS125(BWS)
It doesn't come off…
I thought it would be perfect for a dress-up.
It took a lot of work to get the Bolt off.
You need a diagonal Wrench.
I used Wrench and it worked.
View detail
I'm a little disappointed that I haven't scratched that itch.
[How is it used?
Currently in use after installation.
Was the one you received as per Image?
I was surprised to see that there were more bolts and colors included than the Image, and that the instructions were well written.
Was the installation difficult?
It's easy to install, but as you say, the Bolt length is too short to be effective as a Slider.
The Bolt is available in two sizes, 40mm and 60mm for both M8 and M10. I thought it was kind, but the length was not enough to fix the top of the exhaust system via Bracket, so I had to extend it.
I measured and installed 95mm Bolt and φ22×14mm Aluminum Collar after purchasing them separately.
How was your experience with it?
The existence itself is wild, but in the unlikely event that you think about the cost of replacing Silencer, on the contrary, it's starting to look cute! (Lol)
The effect of Slider is unknown because it has not been verified yet.
[Included Parts:were they on?
For M8Bolt, collar and conversion collar included.
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
I hope Manufacturer will release Long boltType or SliderSingle Item only with lower price separately from this product.
View detail
It's universal, so the effect seems to be mixed.
I'm using it on my GSX250R.
It was installed in the place where the Exhaust Band is fixed.
You will need to purchase a longer Bolt because the included Bolt is too short to install in the first place.
The effect is so-so and solid that it seems to protect you, but I'm a little worried about it. . You shouldn't trust in Overlarge.
View detail
just to be sure
I installed Exhaust Guard
I changed the Exhaust System and used Blue before, but this time I chose Black I did
I installed it as a dress-up, just in case I fell down
View detail
It's up to you how to use it!
I mangled the mini circuit and scratched the exhaust system Installed for later
Because it's a Universal Product, the Bracket Department is a mishmash of unused parts I was forced to wear it I don't know if I'll be protected when it actually mocks, but I have to try mocking I don't want to mock
KOSO has this Not really It's good to have Parts
View detail
Parenthesis OK
I installed it in XG250 TRICKER Now I have Beams Down Type Exhaust System It was easy to install only with the Exhaust Band, but the bolt is attached to the system I used the Bolt of Beams Exhaust System, but the length is Limit It was It would have been perfect if it came with a long Bolt for that purpose I managed to get it on; Others is a product I can't say enough about View detail
It's easy to install and cool
I installed this on a 2000 GSX1300R HAYABUSA Installation itself is very easy, just tighten the collars and bolts that come with it
Unfortunately, it's a little short in length
I installed it under the Exhaust System, but I think it is a little short
A little disappointing in some respects, but very good for the price
View detail
Good size for 125CCScooter
I have installed it on PCX, NMAX and MAJESTYS
I have installed a similar product from another manufacturer before, but the outer diameter is Large I felt the balance is a little too big for the 125CCScooter
This Manufacturer is happy with the size that fits the balance of the look of the Balance just right! It is In addition, if you install it at the same time as the Rear Exhaust Guard, the Manufacturer will also be able to The shape is perfect to match
If only the resin Cap of GuardBody was a Repair item afterwards
If I ever get a scratch, I'll have to buy it from Assembly
View detail
As insurance
Because the position of the Silencer of the Exhaust System which I was wearing so far was inside the Side cover, I did not feel the necessity in particular, but this time Silencer is projecting outward from the Side cover and Titanium, I installed this product as insurance as myself who often coca.
The installation itself is very simple as it is just fastened to the Band to fix the Silencer.
Spacer was included, but it was exactly without using it.
View detail
I think that it is a guardian of Silencer.
Before ordering, the price was cheap so I did not expect much. The real thing is built quite reliably, and it corresponds to M 8 ? M 10 Bolt. M8 Bolt's Adapter is certain and can be fixed without rattling. Since the moss is not yet mossed, the actual strength is unknown, but it seems to protect Silencer of Liter machine without problems if slow moss. Because it is a Type that can separate the ground part and Body, we would like you to sell replacement Parts of the ground part. There are only items that KN plan deals with, and Cost performance is the best. View detail
Satisfied
I installed it in ninja 1000. Aluminum and Slider's resin texture is also satisfying Quality. The price is also cheap, COSPA is also good. Since the attached M10 × 60 Screw is short, I bought 70 mm Screw. I am satisfied with the overall review.
View detail
To BW 'S 125 SEA 6 J
I inadvertently dropped the Tire and had a hard time restoring it
If you carefully work Large is strong.
What is the effect if you try rolling?.
View detail
BW'S125 (SEA6J) To
I tried impulse purchase.
I got lost at the mounting position and fixed several times to fix the position.
Since the length of Bolt was short, I went to buy at Home center and installed it.
Exactly good with M8 80mm.
View detail
We will protect Silencer by standing gobble!
In my Motorcycle history I felt that the stall of the stall was 1, the slope road parking Neutral, the STAND off going out one time, the other car fallen overwhelmingly once, a fall in the corner ring, a collision with Truck... Opponent getaway... Conviction at trial!) Once. Well there were many.
Each time Motorcycle gets scratched.
The Engine side has a Babyface Slider, but if it is only that surely Silencer will pass away...
I bought this product by that.
SilencerQuantity : Quantity if there are 2pc : 2 Set necessary.
Attached is M8 × 40 M8 × 60 M10 × 40 M10 × 60 Bolt and Color.
Ninja 1000 is just right for M10 × 60.
Color seems to be Silver, Black, Gold, Orange, Blue, Red.
This time Silver. It fits well with the car body.
I do not want to take care of me, but I feel secure.
Although it can divide the pedestal and the resin part, can not purchase only the resin part or stated, so it is not reusable?
Would it be okay if it was an integrated type?
Not good for resin molding. BALI BALIBALI. MORIWAKI's Skid Pad was awesome. MotorcycleParts looks great in Large things. Aluminum grinding is nice though it is nice feeling.
View detail