Reviews
Fits: HONDA CB400 SUPERHAWKIII CB400N, HONDA CB400 SUPERHAWKIII CB400N, HONDA CB400TII CB400T, HONDA CB400TII CB400T, HONDA CB400T CB250T, HONDA CB400T CB250N, HONDA CB400 SUPERHAWKIII CB400D, HONDA SUPERHAWK 250 77-79 All models, HONDA SUPERHAWK 250 Reverse 77-79 All models, HONDA All HAWK 250cc models, HONDA All HAWK 400cc series models
It will be heavy, but …
Clutch is heavier but cuts well
No more GEAR loss.
Make sure you prep them well.
View detail
Besides Repair, it is an indispensable Item for Yong Four style custom!
[How is it used?
I bought it to make a Yong Four style Custom.
Was the one you received as per Image?
It was a little cheaply made, but generally as per Image.
Was the installation difficult?
It is easy to apply if you position it and make sure it is tight enough so that no air can get in.
How was your experience with it?
It now looks like a Yong Four. (Lol)
[Included Parts:were they on?
It's not attached.
[Was there anything that disappointed you?
I haven't run in the rain, but it doesn't seem very water resistant.
It has been over 5 years, though, and so far we are still enduring.
If the engine displacement volume is small, it may look like a misinterpretation or an overstatement.
View detail
Fits: KAWASAKI Z400FX/Z400J, KAWASAKI Z400GP, KAWASAKI GPz400F/F2, KAWASAKI Z400GP, KAWASAKI GPz400F/F2
Cheaper than OEM
The deterioration of the fastening nut on the Sprocket has been bothering me for quite some time, and I tried polishing the nut, but it just wasn't refreshing. I thought about getting an OEM one, but then I found this product and decided to buy it.
To be honest, I thought I could get by without removing the wheel if all I wanted to do was replace the nut, because removing the wheel is a pain in the ass. So I decided to remove the wheel.
Replacing the nut was not particularly difficult, as it was just a matter of removing the old one and installing the new one, and stripping the Sprocket of its paint was relatively easy using Holtz stripper. I also used a wire brush and METALCompound to lightly polish and clean the bolt.
As for the Nut, the plating is solid and the loosening stopper works well, so I think it will not disappoint.
It's not a very noticeable part, and functionally there was no problem with the old Nut, but I'm very happy with how it looks now.
View detail
That's what I wanted!
There it is, just what I was looking for!
I was also able to attach it to the KITACO Mirror.
View detail
cheap
It's very different with it. Good to look at.
But if you bend it too far, it will crack. Even if it cracks, you don't have to move the root of Mirror and you can just push it in so that you can't see it. Or rather, it is the price which is good if it replaces it.
View detail
BRCFront Fork Seal
FrontCB400T was leaking Oil.
For the first time I bought a BRC CB400TSeal and looked at it!
It's been about two months and so far no sign of leaking.
It's a RECOMMENDATION because it's less expensive!
View detail
BRCFront Fork Dust Seal
This was my first purchase from BRC!
So far, no oil leaks.
I will buy it again because of the low price.
View detail
For the first time in 24 years Overhaul.
I am very happy with the Overhaul with OEM parts. View detail
BRCFront Fork Seal
It's the first time I've ever bought one of Mr. BRC's
I think it's safe to say that it's a thing!
View detail
BRCFront Fork Dust Seal
RubberI think the quality is good for the price!
So far, no leaks.
View detail
Early life...
[How is it used?
Since OEM Parts are not available, this sale is very much appreciated.
However, 3 years after I replaced it, the push rod side started to leak a bit.
Of course, MASTERBody is free from scratch corrosion.
How was your experience with it?
It's equivalent to OEM Parts, so I think you'll get basic performance for a while after replacing it.
but the track record is that it started leaking after a little over three years.
KawasakiOEM Parts in this area have not been replaced for over 30 years. ・・・・
How did it compare to other products?
I don't have any other products to compare it to... so I can't write about it.
OEM Parts has lasted over 30 years.
[Points to note]
Of course, please make sure that there is no BALI or corrosion inside the Master Cylinder and that the surface is smooth before installing it.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
I guess I'll have to buy it again since it's the only one I have.
View detail
Plating shine is good
This horn has a very nice shiny plating and looks great with American style. This horn has good quality and beautiful plating, so it looks more custom than NORMAL horn. View detail
Mirror Fixation
When I replaced the Mirror, the fixed part was exposed, and I thought it would not look good if it was left as it was, and it would prevent rust, so I installed this.
It looks nice and provides protection.
View detail
Fits: その他 Universal, その他 Universal
Fewer sheets, easier to use
I bought this because I had been using Thickness Gauge which has about 30 sheets and it was sometimes difficult to work with.
This one has only 9 sheets and the Body is thin.
Isn't this enough for a large Motorcycle?
View detail
Clutch lightly?
[How is it used?
I did not change the Clutch master to Radial, nor did I change the Release side Piston.
With this, I thought I could lighten the clutch and use mesh hose to keep the input power from escaping.
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy
How was your experience with it?
I feel lighter.
[Included Parts:were they on?
minimum
[Was there anything that disappointed you?
None
I also found that the Custom feeling was surprisingly obtainable.
The surface seems to be easily discolored by Engine heat.
View detail
z2 mirror review
I bought this while looking for a z2 style mirror to use on the handle of the W800 hurricane z2. It is shorter than the original, so it suits better when the handle is raised and has better visibility. However, the product that was delivered has some scratches. That part is a bit disappointing. -- I bought it while looking for a z2 style mirror to use for the W800 Hurricane z2 handle. The order is shorter, so it looks more suitable and more visible when the handle is raised. That part is a little disappointing Powered by Google Translator View detail
It's expensive, but... this is the way to go for foil washing.
It's expensive, but it's easy to wash the wheel with water.
For oil stains, first "A certain man, a certain man, 556. etc., and then lightly pour off the oil with detergent.
View detail
![Gasoline tank mounting rubber [Stock Type]](https://img.webike-cdn.net/catalogue/19447/0811_TS.jpg)
Fits: HONDA CB400 Fore (air-cooled)
Fuel Tank Mounting Rubber
The rubber parts are consumable parts, so I hope you can keep stable supply. View detail
Fits: HONDA CB350, HONDA CB400 Fore (air-cooled)
Material:Stainless SteelCaliper piston
Haven't installed it yet, but it's got great texture! View detail
OEMGrip is the best?
After all, it's OEM that gets you there in the end. The best! View detail