Reviews
Can not be installed
To install, a screw-in StraightSocket covered by a Rubber Bush is inserted into the hollow hole in the Pivot shaft of the Swing Arm, but the K7 uses a Quantity:Pair (for Left and Right) The Brake Side (Right) is too small and cannot be installed because the attached parts are of the same size. In addition, it is thought that a new car can be installed, but in the case of my car with rust and dirt adhering to it, the Shift Side (Left), which is thought to be the same size, could not be inserted either.
Although it can be machined and installed, it is recommended to use another Manufacturer's
View detail
Fits: YAMAHA YZ 125, YAMAHA YZ 250, YAMAHA YZ 250F, YAMAHA YZ 450F
No, not very good.
As an overall evaluation, we have no problems with the material of the plastic part.
However, there are a number of critical problems with the other aspects of the program, and we do not recommend it as a general comment.
・Screw
This screw is included as a new item because it is co-tightened with the clamp section, etc. However, the accuracy of this screw is so poor that it cannot be hand-tightened with a ScrewSingle Body.
After machining the Screw with Dice, it finally went in.
In addition to the problem with Screw Mountain, there are other parts with surface scratches and other concerns.
In addition, although an Instruction Manual is included, it does not explain which screws to use and where to use them, and the quantity of screw holes is not included, even though they are to be used for the co-tightening described below.:The diagram is such that 2pcBolt will be included.
It is better to confirm the actual match only as a reference for assembly.
・Disc Side
Cannot be installed without modification
The discCard is installed after the Fork bottomGuard is installed, but even with the BottomGuardSingle Body, the screws cannot be inserted due to interference and distortion of the large screws. However, the distortion remains, so it is necessary to hold the whole body down while installing the screws.
The Glasses Wrenchetc. tool with a handle will not fit due to the shape of the area around the screw hole.
In the meantime, there is some relief in this regard, as a thin meaty Box can fit in it.
The bottom guard and disk guard are fastened by a single screw on the inside of the clamp, but the accuracy is not good, so serviceability is also a problem.
Opposite side
There were no accuracy issues here.
One point of improvement is the replacement of the hexagonal screw that holds the Fork Guard in place with the included screw, but this screw pops out quite a bit.
Originally, the head height was designed to be lower than that of the plastic Guard to prevent damage to the head of the Screw in the event of a fall, etc. However, since the attached Screw is a bolt with a normal head, it sticks out about 8mm.
This condition will quickly ruin the Screw as it is the part that is most likely to be bumped during a fall.
I thought it would be better to find some good Screw and replace it.
View detail
The product is a good one, but ….
The two POLISPORT attached StickerLarge cards were not included. Did they get pulled out?
The delivery time is also the worst.
View detail
Fits: BETA RR125 2T, BETA RR390 4T, BETA RR300 2T, BETA RR350 4T, BETA RR200 2T, BETA RR250 2T, BETA RR430 4T, BETA RR480 4T, BETA X-TRAINER250, BETA X-TRAINER300
Is it all like this?
Why is it so crooked when new?
Are you licking your chops?
Even if it's made in a foreign country, it's too much.
Wonder if all of WeBig's inventory is this crooked.
Do you not inspect the product?
View detail
It's not a bad thing
You will receive something different from the picture.
Please note.
View detail
The SEROW225 W has
It was different from the picture. The upper part was not squeezed and the thing arrived.
I made the mistake of choosing it based on the video. I should have read the description carefully.
It's cheap and things look good, but it was short for ??????SEROW225 W.
View detail
Fits: GASGAS MC450F, GASGAS MC250F, GASGAS MC125
erroneous product
This is the part number for the Exterior Kit for the Gasgas MC, but only the Rear Fender arrived for the EC.
If it's for MC, there should be no protrusion for tail lamp installation, but the one I received is the shape for EC with protrusion for tail lamp installation.
The air cleaner box for EC has a hole for penetrating, and the hole must be blocked to use it without the tail lamp.
I can't return it because I stuck Decal on it right after arrival. I'm reviewing it to alert other buyers.
View detail
Eurasian bullshit
The answer was that it would arrive in a week or two, but I ended up waiting four weeks. Too much of a wait!
You made me wait too long! You want me to make a difference? You made me wait too long. You made me wait too long. I've been waiting too long.
View detail
This is a Large person Elbow guard
Regrettable to the product name
In the product name DEVIL knee/Shin guard and notation
Size" in the product information column:for Adult"
Only in the product description in the product information section
Devil Elbow guard Quantity:Pair (for Left and Right) "
and notation
It's actually a Large person's [Elbow guard] Is [Children] s knee/shin guard
Large The knee/shin guard for men is separate
https://www.polisport.com/downloads/Polisport-Off-Road-2020.pdf
Large I bought this as a knee/shin guard for a person, so Cost Nothing but performance has been rated yet
Cost performance is the worst
View detail
Oh, no
I've written an impresario before, but I'll add to it 。 The lock lever at the bottom broke off while I was using the Motorcycle It's hard to lift, and it breaks in a flash, so this is a useless STAND! I've already arranged for a new STAND, but this is not the way to go when it's so expensive I will never buy anything from this manufacturer again View detail
Fits: Others
A shitty product, not a shitty product
I bought it because of the comments that were written about how relatively easy it was to install Do you get it? Level called
When trying to force the wire into place by force, it is not possible to use the Clutch Wire or the Throttle Wire Interference is inevitable To avoid the interference, both Brake and Clutch Lever started to go in a ridiculous direction
I think it looks good, but if it doesn't stick, it doesn't mean anything
Worst, worst, shittiest product ever
Large It's like throwing away your gold
This is a product you should not buy
I know you can't do it, but I dare say it, Gold back!
View detail
Dissatisfied
I am on a dTRACKER.
I bought it because it was cheap at Sale, but it looks like Large texture, and if I lift it up I will not even get my feet even on my hands. It is very inconvenient..
I can not lift with a force that is half-baked.
View detail
Fits: BETA RR350 4T, BETA RR300 2T, BETA RR250 2T, BETA RR125 2T, BETA RR480 4T, BETA RR430 4T, BETA RR390 4T, BETA RR200 2T, BETA X-TRAINER250, BETA X-TRAINER300
Bad product precision
This time for the first time I bought a poly sports product, but I took it out of the bag, firstly the product is thin compared to the OEM!
Right Side is attached Screw hole accuracy is poor, it can not attach to Smooth, it is warped.
Left Side has good accuracy but Screw of Brake hose clamp has been licking from the beginning! Moreover, since Screw protrudes to the Reverse side, processing is necessary.
Since it is an overseas product, I can endure somewhat of the installation accuracy etc, but this evaluation is because Brake hose clampScrew is not allowed to lick from the beginning. I will not buy anymore, I can not recommend it!
View detail