Reviews
Thhank you
Thank you!!About quality and texture About the feeling of use Products to buy together Difficulty of installation Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasingAbout quality and texture About the feeling of use About Design About Size Chart Cost performance and comparison with other products About shipping and packaging Any concerns, cautions, or advice when purchasing View detail
I installed it on my NINJA150RR.
It is very lightweight and made of glass fiber, easy to work with and solid. The installation was done with NylonStrap. View detail
Fits: HONDA NSR50, HONDA NS50 R, HONDA NSR80, HONDA NSR mini, HONDA NS50 F, HONDA NS-1, YAMAHA TZM50, HONDA NSR50, HONDA NS50 R, HONDA NSR80, HONDA NSR mini, HONDA NS50 F, HONDA NS-1, YAMAHA TZM50
Used in Circuit
Seat rubber is a consumable item for circuit driving, but I think it is a good product with no quality problems and excellent cost performance. I recommend it. View detail
Bolt hole cracked.
[How is it used?
Installed to prevent oil leakage at Circuit
Was the one you received as per Image?
Street Image
Was the installation difficult?
There was no Instruction Manual, and at first I did not understand what the bracket in the Included Parts:section was for. After installation, I found out that the bracket was to be installed by lowering the cowl to avoid the exhaust pipe.
Installation is not that difficult.
How was your experience with it?
As shown in the photo, the Bolt mounting holes on the Cowl were cracked after only a few runs, whether due to poor installation or slightly poor product dimensions.
However, it may be unavoidable in a sense, since Grom is a Machine with very high vibration.
[Included Parts:were they on?
Bolt、Bracket Only。
[Was there anything that disappointed you?
Cracking. In the meantime, it did not become a fatal Damage, so it is usable.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Tightening the bolt a little bit at a time is recommended, as tightening the bolt too much may cause the cowl to crack. Also, I would like to see an Instruction Manual.
View detail
Some difficulty in installation
[How is it used?
Circuit's Sports driving
Was the one you received as per Image?
As per Image… I thought.
Was the installation difficult?
The hole position was not sober and needed to be fine-tuned with a stick File.
How was your experience with it?
Perfect! It was very Race ish.
[Included Parts:were they on?
Only Cowl to begin with.
[Was there anything that disappointed you?
I knew I wanted the hole to be in the exact position.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If you are going to Race, you will also need a number seal.
View detail
Fits: YAMAHA Cygnus X, YAMAHA BWS125, YAMAHA BWS125
When in doubt.
Used with CYGNUS2 model.
I wanted to raise the ride height from the OEM rear suspension to secure the bank angle, so I used the XMAX OEM suspension, but it gave me a strong feeling of being shattered and the cornering was unstable.
When I was looking for Other Brand Product's Rear Suspension, I chose this product because it is a suspension that is highly used by CYGNUS riders and it is also capable of overhaul.
Damping can be adjusted for both extension and compression, which is rare in this price range.
I bored up the rear axle output to 15 horsepower, but the suspension didn't lose any power, and the ride became quite tight.
In particular, the ride height is exquisite. If it is too low, the motorcycle will not be able to lie down because it will rub the side cowl, but if it is too high, it will lean forward and the front will be defeated.
I have been using it for about 10,000 km and there are no oil leaks, etc. I think the durability is very good.
View detail
I am satisfied
It feels good to install. I haven't mocked it up yet, so I haven't tested the effectiveness yet. View detail
Number Seal Cowl。
I bought it for Circuit, and I like the sharp feeling than Cowl of HRC Grom.
However, although it is White Gel Finishing, it is not a very beautiful finish, so it needs a certain finishing treatment.
(If you don't mind, it's perfectly fine.)
View detail
Cowl Protection and Dress-up
You just need to replace it with OEM Bolt, but you need to break the Bracket on the NSR50 because the Cowl on the Right Side is a Quick Release Bolt.
For myself. I had a spare Bracket without Bracket, so I replaced it with that and installed it.
I put it on just in case, but hopefully thisParts will not be active.
View detail
Fits: YAMAHA Cygnus X, YAMAHA BWS125, YAMAHA BWS125
You can make a wide range of adjustments, and Anodized is beautiful!
What made you decide to buy?
In OEMRear Suspension, I wanted to raise the ride height because it rubs STAND Purchased
In the direction of Custom, I wanted a red color, so I went with this one
How was your experience with it?
First of all, it's beautiful to look at
I'm glad I bought it before I installed it
It's quite noticeable from the rear of the car, giving you a custom look
When you actually install it and drive it, the ride is hard but flexible, which is a strange feeling
It also raises the ride height, so it felt a little high on my hip until I got used to it
The matter of rubbing STAND, which was the purpose of the purchase, was lessened, but not for Zero
I haven't used all the adjustment features yet, so I'm going to try out different things in the future
Was the installation difficult?
The installation itself wasn't difficult, and I was able to replace it in about an hour, working slowly
However, knowing the tightening torque of the Bolt that has fixed the Rear Suspension You should have a Service Manual, because you need to have one
【Please tell me the installation point and hang】
The CYGNUS X has two Rear Suspensions, so I'll be replacing one at a time The length is different between the OEMRear Suspension and this product
So when you work, you can put your foot under the tire and move the tire up and down It works
[Was there anything that disappointed you?
The performance and appearance of the product is great, but the Instruction Manual is included and the product is very good I didn't know how to adjust it because I hadn't done so (Webike later solved the problem for me.)
Do you have any wishes or improvements you would like to make for the Manufacturer?
The Instruction Manual is pricey for custom parts for mopeds, so the Instruction Manual is I think it would be better to have
For a layman like me, it's hard to tell which Dial is an adjustment to what
[Do you have any products to compare it to?
B-MOON FACTORY Z-1 Rear Suspension
View detail
Fits: HONDA Grom(MSX125), HONDA Grom(MSX125)
It's a sturdy structure
If you try to attach it with the Screw of OEM, you can use it with the Cowl You need to put something between the frames, but that's just the way the groms are constructed I use the rubber packing which I drilled a hole in between the frames View detail
Fits: YAMAHA CYGNUS X, YAMAHA BWS125
Nice
In the past, I was using KS project SUO BUSOO Shock but Damper? Was too effective? Even if I loosened Spring to the weakest, it was too hard and I pushed Pushing from Spring Since it was uncomfortable, I changed it to Koch, I can adjust my damper so it will be my favorite fee Ring Recommendation. Weight also feels light with Reserver tank (I feel the same as light KN) Cost is ☆ 4 because the price is high. View detail
Fits: HONDA NSR mini, HONDA NSR80, HONDA NSR50, HONDA NSR mini, HONDA NSR80, HONDA NSR50
Style is good!
There is no Instruction Manual and the shape of Seat rubber does not match!
It is useless unless you can process holes to a certain extent, such as drilling and cutting!
Seat shape is cool !!
View detail
Fits: HONDA Grom(MSX125), HONDA Grom(MSX125)
Even though it is an exclusive product, ingenuity is necessary
I think only to remove the OEM and install it
We had to fill the space with Aluminum Collar etc..
Included Parts because it is drilled : I wanted you to put it in, so the evaluation is low.
Odd so I can fulfill the purpose
View detail
The surface is rough
It is Gel Coating, but it was not beautiful enough to paint as it is.
First of all, in order to fill in the fine irregularities on the surface, we have to process the surface with Pate.
Design is nice Parenthesis ♪ It is certain.
View detail
At CYGNUS X 1yp...........
Previously I was using KITACO but purchasing this item with Heador every change in Projectorization. Double-sided tape got removed so paste the 3M at home Finally installed. Result KITACO is better View detail