Reviews
Fits: HARLEY-DAVIDSON XL1200R Sportster, HARLEY-DAVIDSON XL1200R Sportster
Ideal for SelfOverhaul
Every year we refresh each part of the motorcycle as it goes into hibernation, and this year we chose the FCR Carburetor Body.
I received the product and was Big surprised.
Case is magnificent! (I'm not being sarcastic, really.)
SettingSeat was also included for reference.
I am looking forward to the Under-seat engine hall at the end of the year and the beginning of the new year.
View detail
Fits: HONDA Hawk III CB400N, HONDA Hawk III CB400N
To revive old cars
Without it, revival would have been impossible.
I appreciate that Rubber's parts are all available,
View detail
Carburetor malfunction
Idling was unstable, and when I twisted the Axel from a constant speed, it would momentarily bump around. I thought it was just this kind of thing since I bought it, but every time I looked at the plug, it was completely black and would not pull a chalk during the winter. I thought the fuel was leaking from the bi-starter valve, so I replaced the bi-starter with an OEM one, but there was no improvement. I replaced the main, Throw, Needle, Pilot, and Pilot screws. (It also came with a by Starter screw, but I didn't replace it this time because I replaced the OEM screw last time.)
As a result, Idling was stabilized and running was improved. However, I could not figure out what was the cause of the problem because I changed all the parts at once.
The other day I changed the exhaust system from NORMAL because the fuel condition was getting better, but I felt that it became thinner as it was draining a little better. I also appreciate the fact that I can adjust the density by myself.
View detail
Fits: KAWASAKI barios, KAWASAKI barios, KAWASAKI barios, KAWASAKI barios, KAWASAKI barios, KAWASAKI barios, KAWASAKI barios
That's Key Star, no doubt!
You can't go wrong with Key Star, even if it's expensive!
The only thing that hurts BALIUS is that it requires four.
View detail
Setting around Carburetor
For setting out around carburetor.
It was very convenient.
There is also a beginner-friendly Instruction Manual.
I can recommend it.
View detail
Fits: YAMAHA FZ750
Used in Maintenance
Almost the same product as OEM Parts, but the shape of some of the float packing is different. (Possibility of difference in year etc.?) View detail
![Fuel Kit & ThrottleValve Guide Gasket[Quantity:1 Set for 1 Cylinder]](https://img.webike-cdn.net/catalogue/images/30752/FH-5203NRP_1_TS.jpg)
Fits: HONDA NSR250R, HONDA NSR250R
Carburetor setting
It is a very old carburetor, so it is used for overhaul and setting.
Complete set Quantity:Set and is good for replacement and readjustment.
It is a good product at a better price than Single Item purchases.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZR1100, KAWASAKI ZRX1100-II, KAWASAKI ZR1100
ZrX1100Powerfulization
ZrX1100 is converted to Powerful and
I've tried JetSetting, which is a common practice.
I was having trouble getting it right.
The internal parts of the carburetor can also be renewed.
I thought it was a good time to buy a KeyStar Fuel Conditioning Kit.
4.000 yen per cylinder is not expensive. You can check the price of OEM products.
Quantity:The darkest Jet Jet needle for both MJ and PJ is R
Only tuning in and running as soon as possible.
It blew up with no problems at all.
There were a few jittery moments at low speeds.
I would like to make some (thicker) adjustments by changing Pilot screw, PJ, etc.
At this stage, it blows up beautifully, and no chalk is needed at EngineStar.
View detail
Fits: KAWASAKI GPX250R-II, KAWASAKI EX250
Excellent carburetor rebuild kit
I purhcased two Keyster carburetor rebuild kits for my Kawasaki Ninja 250 and I was very impressed with the quality. All of the small parts are organized in nice plastic containers and it came with all of the gaskets I needed & a huge selection of jets & needles for tuning. I'm very happy with Keyster carb kits View detail
Fits: HONDA NSR250R, HONDA NSR250R
Maintenance
When the carburetor is overhauled, it is replaced with a new one.
If you want to purchase a single item from HondaOEM Product, please click here for the quantity.:It is helpful that the Set purchase seems to be complete and inexpensive.
View detail
Carburetor overhaul
All the parts you need for your Overhaul are available and are more economical than buying from OEM Parts.
The component accuracy was good and reliable.
I drove about 1,000Km after the replacement and I am satisfied with the Engine's condition.
View detail
A strong ally when OEMs are out of stock
Purchased when replacing 400 to 500Engine because OEM was out of stock.
It is pleasant.
View detail
It's convenient
If you are worried about the carburetor setting, we recommend you to try this product during O/H!
It is easy to set up because some reference points are available in Manufacturertest.
It saves a lot of time.
I also used it on an FCR Carburetor Body and it was easy!
View detail
Fits: HARLEY-DAVIDSON road rider
The keihin fcr carburetor repair kit includes many replacement parts. according to the picture of the product will try again View detail
Fits: HONDA FTR223
Setting after AICancellation is almost a no-brainer!
For carburetor setting and parts replacement after AICancellation.
The most important point is that it comes with 4 types of JNs, a new Holder and a Needle Jet (replacement parts required in some cases).
The OEM JN on the FTR (CB) can only be used with up to 2 washers, which makes for an unsatisfactory finish setting, but this fuel kits will surely solve this problem.
A Minus screw machined Pilot screw is also included, but this is just an extra. (DDriver is needed to remove the OEM, so an additional expense of about $1,000 is required.)
By the way, OEM JN is about 4,000 yen, so this is definitely a better deal even for the purpose of JN exchange.
＜〜Use it and see.
I am a Normal muffler and air cleaner, but when I tried MJ125/PJ35/JNX1-RR, I can now turn it without difficulty in the whole range, especially at low speeds. (In other words, I can see why just putting Washer over JN and adjusting it was not enough.)
We do not recommend AICancellation to everyone, but if you are interested in trying it out, please do so.
View detail
For VIRAGO
Cost, quality, etc. were TOTALLY good!
I am considering purchasing a spare!
View detail
Fits: HONDA TL125 Ihatov (TL125S), HONDA TL125 Ihatov (TL125S)
Carburetor setting essentials
The parts necessary for OH and setting of the carburetor are all here, so there is no harm in purchasing it.
There are several types of jets in the box, and the instruction manual is very kind and helpful, and I am enjoying the various settings.
View detail
Fits: YAMAHA XT250X
I'm not sure I'm ready for this one.
Quantity:I did a carburetor OH using the parts in the Set (except the ThrowJet needle), but I had frequent gasping for breath while driving due to the rising temperatures and altitude….
Subsequent replacement with OEM parts
(1) Float valve replacement → no effect
However, I think the blowback to Air cleaner is gone.
(2) Jet class (OEM back MJ?PJ) →no effect
PJ is the same #34, but OEM is better.
(3) Tank cap and fuel line checked → no problem.
OEM back the Needle and Needle jet holder section above ? below
Now I finally don't have to hold my breath anymore….
MJ?PJJet and the like can be used, but it may be safe to assume that the Jet needle and Holder part cannot be used!
I'm really tired….
View detail
Dream Carb Kit
This kit is arguably the first part you should buy for your Dream 50. You would never be wrong, just to keep it for future in the case bike's carburator requires adjustment. I highly recommend this product View detail
Overhaul of TA22Acarburetor
[How is it used?
NSR250R purchased at a certain Oak Auction (MC21) I purchased this product for the overhaul of KEIHIN's TA22Acarburetor.
I have been a customer of KeyStar's Kit many times before, so I chose it without any particular comparison to other products.
Was the one you received as per Image?
Quantity as shown in the photo:Set has arrived.
Quantity:Pair (for Left and Right) The parts are all the same in the Quantity:Pair (for Left and Right) The good thing about MC21 is that you don't have to manage the
Was the installation difficult?
There is no particular Instruction Manual, but there were no particular difficulties.
Only the O-ring of the chalk part seemed to be a hassle to replace, so I left it as it was, but the others are working normally.
However, I had to force Needle's Holder in a bit, so it was deformed....
Brass parts, so care should be taken not to force them into place.
How was your experience with it?
The car was originally immobilized but was successfully engineered.
There are no problems with the packing and no overflow occurs.
We were able to Refresh carburetor successfully.
[Included Parts:were they on?
As you can see in the picture, this is all you need to buy, and several Jets are pre-installed.
This product does not come with a Throttle valveGuide Gasket, so if you need one, you should purchase the one that does.
[Was there anything that disappointed you?
Not really!
【Review】
I had no problem at all with the product, although I deformed some of the Parts due to my carelessness.
It is nice to be able to buy everything in its entirety at a lower cost than ordering OEM Parts piece by piece.
View detail