Reviews
Replaced because the OEMBlinker can't tell it's blinking in the daytime.
[How is it used?
It became difficult to tell if the OMBlinker was deteriorating over time or if it was blinking in the daytime. This is dangerous. So we decided to replace them with LEDs.
I chose this one because it seems to be for Off-road.
The Relay has already been replaced with an LED-compatible product, so this is the only purchase.
Was the one you received as per Image?
It is hard, although it is described as Rubber-like.
Was the installation difficult?
The work itself is not a problem, but the RightHand guard of our car is distorted, so we had to use the enclosed Attachment parts to make it slant down! (Sweat)
How was your experience with it?
It is brighter and easier to see from oncoming cars, etc.
View detail
It is quite convenient to have it in Single Body.
I purchased the Racer to make it a public road Spec.
Quantity of electrical components:I could have bought it as a Set, but I bought this one because I can reconfigure it in various ways.
This will bring together the electrical system for the time being.
The terminal connections are in good condition and are securely fastened with Heat Shrink Tubes, so they appear to be water resistant.
View detail
DRC MeterScreen ProtectiveFilm
Even if air bubbles appear, they will disappear in a few days, making it easy for beginners to apply.
If it fails, it is conscientious because it comes in a two-pack.
View detail
DRC MeterScreen Protect Film
It is very easy to put it on.
Even if there are some bubbles, they will come out in a few days.
No more worries about scratching.
View detail
This is a highly Universal Tail lamp.
Universal Tail lamp
[How is it used?
I had been looking for a replacement for my KSR-II for many years, but I could no longer install the OEM Product's Tail lamp, so I went to Webike to find one. However, I found this product when I was looking for a replacement for the OEM Product's Tail lamp.
Was the one you received as per Image?
It is a product that is more than an image in the form that has good visibility with the Edge effective design while being compact, and also has universal characteristics that can be installed from off-road motorcycles to road sports type motorcycles without any sense of discomfort. It is a product that is more than just an image.
Was the installation difficult?
As mentioned above, this is a work to install a bracket for Fender Eliminator, which is a self-made bracket, so the drilling and wiring processes are performed in actual products, so it may not be of much help.
After installing it on the Fender Eliminator, all you have to do is connect the wiring of this product to the wiring for the tail lamp on the body of the vehicle, but this product does not have the wiring that is often found in this type of product. "Bullet Type Terminal Spec
Modern motorcycles have connector terminals, so it is easy to find a connector that fits the vehicle body on KITACOConveniencePartsetc. and modify it to make a simple connection.
Fortunately, KSR-II has Bullet Type Terminals for most of the terminals that connect to the lights, so we were able to connect without any modification.
How was your experience with it?
There are no problems with the functionality of the LED bulbs, which have been in place for several years now and are functioning as well as they did immediately after installation.
My personal impression is that the rounded design of the KSR Tail would fit better with the rounded design of the Tail lamp than the pointed design of the Tail lamp. I think that the rounded design of the KSR Tail lamp fits in better than the sharp design.
I had a friend install it on his WR250 after that, and the shape of the tail and the design of this product matched very well, and I honestly thought Parenthesis was good (this is just my personal opinion).
[Included Parts:were they on?
It was a Simple Package with only Body and Instruction Manual.
[Was there anything that disappointed you?
Not at all.
Aside from the above mentioned compatibility, which is a matter of personal preference, I have no complaints about the product design or the kinability of the product.
Other items that would be helpful
Point and hang of installation
This product is a Tail Lamp product, but a vehicle-specific kit that uses this product is also sold by DRC.
The price is a little bit higher, but the Bracket for each car model is also of high quality and you will not feel any discomfort after installation. It's a Manufacturer's product." I am convinced that this is the right product.
For those who, like me, cut, paste, and fabricate to install, please measure the dimensions carefully or do your best to install the product as-is.
[Availability and clarity of the Instruction Manual
An Instruction Manual is included in the package.
[Notes]
Nothing in particular, just be careful not to misplace Wiring.
[ITEMS TO BUY TOGETHER
As I mentioned above, this is also available from KITACO and other companies. OEM Type Connection Terminals by Manufacturer will allow one-touch connection to Harness on the car body side.
Since the method of fixing to the car body varies depending on the car model, it may be better to try a temporary assembly before full-scale installation.
First, check the fixation method by placing it on the vehicle in which you want to install it.
[Opinions and requests to Manufacturer
Please keep up the good work in maintaining prices as much as possible and keep selling for a long time to come.
View detail
Thank goodness I can buy only Lens.
I know that Blinkers on off-road vehicles are often damaged in a fall, but it is very nice to know that DRC products are available only in Lens and can be replaced.
I was impressed that DirtFreak products understand Off-roadUser very well.
View detail
Simple shape
OEM and replacement.
There was a Space-like difficulty in installing it on the Fender Eliminator Kit.
No Large problems.
As said in other Reviews, note that Body strength is low.
Also, be careful when converting old cars to LED because it is easy to have problems with Relay.
View detail
Fits: HONDA CRF250L, HONDA CRF250RALLY, HONDA CRF250L
Fender Eliminator and led
[How is it used?
Fender Eliminator conversion made it look like I like it, as per Image.
Was the one you received as per Image?
It was heavier than I expected.
Was the installation difficult?
I had a little trouble with the installation.
The lower mounting part attaches to the outside of the
I couldn't figure it out and tried to install it on the inside.
I was worried that it would not fit.
How was your experience with it?
It's good
I have no protection against rain or water from washing the car.
We'll see how it goes.
[Included Parts:were they on?
Screw has some parts to be diverted.
[Was there anything that disappointed you?
Instruction Manual, because we are making it universal.
I don't know much about it.
I feel like I can handle it.
Other items that would be helpful
Buy together
Reflector kit for D45-07-300 has been
I think it is necessary.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Quantity:1 Set of 2pcs. is Point
Quantity:1 Set of 2pcs. would be appreciated.
If you are going to put it on, it would be better to do it as soon as possible in a new car or after a thorough cleaning. The two-lens meter is a little curved, so you may need to hang it.
Although it is a good product, the included spatula is made of paper, so when it absorbs moisture, it becomes soft and difficult to apply.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
Safe if you put it up first.
Once it is applied, it blends in so well that you can't even tell it's there.
It is good for preventing scratches, and if it should get damaged, it may only be a matter of replacing the film.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
Quantity:1 Set of 2pcs. is good
The first one failed.
Apply a large amount of Film Paste Spray to the film and paste it well.
The second one went on well. It's so good that you can't even tell it's on.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S750, SUZUKI SV650, SUZUKI SV650X
more than I thought
I bought two pairs, thinking they would not stick nicely. But they were easier to install than I expected. Highly recommended. View detail
DRCMeterScreenFilm
I installed it to prevent scratches on the meter. The first one failed because I misread the Instruction Manual and made a mistake on the gluing surface.:1 Set of 2pc. so the next one was OK. Installation is easy. View detail
What a surprise to find out that it is LED.
The NORMAL Tail area is very heavy.
It is also heavy in appearance.
So the familiar DRC makes it look good and lightweight.
Smoked lenses make it even more beautiful.
Tail Bulb What are we going to do? Do we have to make our own?
Thinking that maybe it was LED from the beginning?
The product I received was LED and all I had to do was Bullet TerminalWiring.
There is no mention of LED in the DRC product description, and when I saw the picture, I wondered if it was LED. I just thought it might be an LED.
This completes the LED conversion of the MD44.
NumberWhite lighting is also available, so driving on public roads is OK!
Other cheap ones do not have White lighting and can be cut off for poor maintenance KIP. Please be careful.
Bullet TerminalWiring can do the installation by itself (I also performed the soldering just in case).
You must be able to disassemble and remove the Blinker yourself.
This is not included in the DRC installation instructions.
CRFRALLY50 is quite a hassle to disassemble the Rear blinker.
If you are concerned about this, please confirm that you can remove all the BlinkerUnit from the actual vehicle before ordering and DIY installation.
Connector is too hard to pull out, what's the lock? or "What is the Blinker Vibration Eliminator Bush? If you have any questions, please ask the Shop from the beginning.
I am most afraid of failure in the electrical system.
1:Short and can't tell where it broke.
2:It doesn't work to take it to Shop.
3:Even if you take it with you, it will cost quite a bit of money because you will have to examine it from scratch.
and it is essential to triple the pain.
Tools needed are 8, 10, 12mm Wrench & Spanner, Radio pliers, Nipper, 5mm Hexa, Phillips Screwdriver, Slotted screwdriver (used to remove connector).
I wrote a scary story at the end, but it makes Parenthesis good for more than the price.
It can be very Recommendation. Except for the mud splash... (^^;)
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI D Tracker X, KAWASAKI KLX125, KAWASAKI KLX150, KAWASAKI KLX250, KAWASAKI KSR110, KAWASAKI Ninja 250, KAWASAKI Ninja 250R, YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6 04-17, YAMAHA FZ6-S Feather, YAMAHA FZ8, YAMAHA MT-01, YAMAHA MT-07, YAMAHA MT-09, YAMAHA TDM900, YAMAHA V-MAX 1680, YAMAHA WR250R, YAMAHA WR250X
Bracket
It is used to replace the Blinker, without which it cannot be attached. View detail
Outstanding!
Really good,sturdy build quality and brightness! I used them on my Kawasaki D tracker X. Arrived within a week to Sri Lanka! View detail
Fits: KAWASAKI ER-6N, KAWASAKI Z800, KAWASAKI Z250SL, KAWASAKI Z125 PRO, KAWASAKI Z1000, KAWASAKI VERSYS300, KAWASAKI VERSYS250, KAWASAKI VERSYS650, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI NINJA650, KAWASAKI NINJA1000, KAWASAKI Ninja 400, KAWASAKI VULCAN S, KAWASAKI H2, KAWASAKI NINJA250, KAWASAKI KLR650 08-17, KAWASAKI Z900 17, KAWASAKI Z750 05-06, KAWASAKI Z650 17
Pay attention to the car model and combination parts.
When we converted to a small type blinker, we wanted to install a SMART blinker in the OEM position, but when we removed the OEM blinker, there was a large hole in it, so we could not install it as it was.
At first, we were concerned about how to plug the holes and while doing some research, we found these Parts.
I didn't know such a convenient thing existed! I was impressed.
This is a necessity when installing an external blinker in the OEM position.
This is not a problem with this product, but be aware that depending on the Blinker you replace, the distance from the vehicle body to the BlinkerBody may be shorter.
The Z900 I installed has an ODAX Screen, which is so wide that it hides the inner part of the Blinker just a little.
View detail
I'm using it attached to the Hunter Curve instrument panel. I am satisfied.
Since the two pieces are in one set, the installation failed due to a small mistake at the time of the first installation, and fortunately, I tried again with a spare and succeeded. I sprayed it with water mixed with a little neutral detergent to thoroughly wash off the dust, etc., and installed it. It can't be helped that it can't block sunlight reflection, so depending on the time and direction, the sunlight is reflected and it's hard to see. -------------------------------------------------- -------- Two copies were included in one set, so when they first installed, they failed to mount due to a small mistake, and fortunately they tried to re-attempt with leisure. Sprinkle with a bit of a mixture of neutral detergent, washed off and installed enough dust. It is inevitable that the sunlight is reflected in time and direction because the reflection of the sun is not prevented, but I liked it to be well protected from the wounds due to the fitting and the small dust. Powered by Google Translator View detail
Fits: KAWASAKI ER-6N, KAWASAKI Z800, KAWASAKI Z250SL, KAWASAKI Z125 PRO, KAWASAKI Z1000, KAWASAKI VERSYS300, KAWASAKI VERSYS250, KAWASAKI VERSYS650, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI NINJA650, KAWASAKI NINJA1000, KAWASAKI Ninja 400, KAWASAKI VULCAN S, KAWASAKI H2, KAWASAKI NINJA250, KAWASAKI KLR650 08-17, KAWASAKI Z900 17, KAWASAKI Z750 05-06, KAWASAKI Z650 17
Necessities
When installing an external Blinker, it is necessary View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S750, SUZUKI SV650, SUZUKI SV650X
For Meter Protection
The way to paste and Included Parts:are the same as Film on the phone. Even if you make a mistake, there are two sheets in the package, so you don't have to worry. View detail