Reviews
Used to replace Exhaust System of CRF125F
We have replaced the Exhaust System of CRF125F with DELTA products.
Installed; NORMAL Guard will not work.
Therefore, we installed the same product as recommended by the manufacturer? The same product recommended by the manufacturer was installed.
Exchange is Quantity:It is easy as it only requires 2pc Bolt and Band.
I thought 15 minutes would be enough time to work on it.
It is also effective in blocking exhaust heat and idles for a while.
After turning the Engine with Ring, put on the Gloves.
I've tried touching it, but it doesn't feel hot enough to melt.
It was
(If the Engine is heated by Race or other means by continuously turning the Engine.
I haven't tried to see what happens.)
The texture is solid, and even a slight bump is not enough.
I am relieved that it does not seem to be broken.
View detail
Recommended
We installed this product to replace an external Exhaust System on a CRF-125F.
The price was lower than other manufacturer's products, which was the deciding factor in my decision to purchase this product.
View detail
To avoid scorching Pants.
The exhaust pipe of EXC-F has no guard at all, so the moto pan will soon be burnt and perforated. Guard is necessary because the exhaust pipe also gets burnt and dirty.
OEM is a high-end product that costs more than 10,000,000 yen, so it is hard to afford, but this is a commendation at a reasonable price.
View detail
Burn Prevention
[How is it used?
It is used on a 2022 CRF250RX.
The Exhaust pipe is directly on the side of the body, so if it falls over and gets caught between the legs, it will likely not be hot enough.
I heard that if the Jersey was melted, it would be enough, but if not, the nerves would burn out and there would be no way to recover.
Was the one you received as per Image?
It was more solid than I expected.
Was the installation difficult?
Very easy to install, just adjusting the angle to allow for the slotted screwdriver.
How was your experience with it?
Fortunately, I haven't been pinched yet, but when I touched it to try it out, it wasn't hot at all, so I knew it would work. Relieved.
[Included Parts:were they on?
Body and Band for fixing.
[Was there anything that disappointed you?
None!
If I had to say something, I would say that when the exhaust pipe rubs against the body, there is a very unpleasant sound of the gold material rubbing against each other.......
View detail
good-looking
OEM Product is not so good, but I'm glad I bought this Heat Guard because it looks great.
However, it is thinner than I had imagined and I would like it to be made more firmly.
View detail
Prevention of burning of Up Exhaust Pipe
It is easy to install because it can be bent freely along the exhaust pipe. It is easy to install because it can be bent freely along the exhaust pipe. View detail
Fits: KAWASAKI KLX125, KAWASAKI D Tracker 125, KAWASAKI KLX150
The last one.
I bought it again because it was new and somehow it got into the back of the MiddlePipe.
I've bought JMCA Certified for places where I can't run without changing the exhaust system many times, but the quality is usually fine.
View detail
Function, good, reed
Mounting to RMX 250. Since it is not so hard material, I will bend it according to the shape of Exhaust Chamber. It is not good looking along with the Exhaust Chamber and it took time to make it fit.
Band of installation is also LargeQuantity : 2 pc, SmallQuantity : It comes with 2pc and can handle any thickness.
Just for Length 125ccClass? Well, it's obviously not enough length for the RMX's Exhaust Chamber that I decided to be cunecne. You can covert Right Side but Left Side is in a state where you can not cover at all.
The previous External Chamber outside the company also became Bekobeko and replaced this time so I installed the Guard, but in intense Hit it seems Dent again. It seems that there will be no strength up to that but it seems that Dent can cover when it falls down.
Gray alumite looks also chic so texture is also GOOD.
View detail
Chamber guard
With Chamber guard installed we were able to travel off-road with peace of mind.
Although it seems that it corresponds to most 2Cycle vehicles, it seems that Length is a bit short, and it is possible to LimitCover to the expansion room. If it was a little longer it was a five star - - -
View detail
Fits: YAMAHA SEROW250, YAMAHA XG250 TRICKER, YAMAHA SEROW225
Although the Clamp of this sort was looked for, it settled in this.It is satisfactory although number Manufacturer examined. They are goods which it can recommend.It seems that structure of details is solid.
Although the Clamp of this sort was looked for, it settled in this.It is satisfactory although
number Manufacturer examined.
They are goods which it can recommend.It seems that structure of details is solid.
View detail
Fits: KAWASAKI KLX250, SUZUKI 250SB, KAWASAKI D Tracker
It is a Gasket of the connection section of a Silencer and an Exhaust pipe. If it reuses here, omission in exhaust steam of most will be carried out.It is mere a few.It reused, although a loud sound did not come out, omission in exhaust steam was carr
It is a Gasket of the connection section of a Silencer and an Exhaust pipe.
If it reuses here, omission in exhaust steam of most will be carried out.It is mere a few.It reused, although a loud sound did not come out, omission in exhaust steam was carried out half a year, and since it was sick, it exchanged in passing.
It is equivalent in it being pure.There is what no fault.Certainly [ way it sometimes held up the hand to the joint part and checked the omission in exhaust steam ].
View detail
In my case, since it went to the path through a wood etc., it purchased targeting the measure against a dent and the Dress-up effect up of an Exhaust pipe.Since it is fixation in a Band, attachment is easy Ching! Probably it comes seemingly to be one laye
In my case, since it went to the path through a wood etc., it purchased targeting the measure against a dent and the Dress-up effect up of an Exhaust pipe.Since it is fixation in a Band, attachment is easy Ching! Probably it comes seemingly to be one layer of
appearance nearby Off, and Cool (smile)
defense also becomes brave.even [ a free ] -- a few -- a price -- it is high ^^;
View detail
Since the STAINLESS-STEEL part melted when the Motorcycle cover was hung, it processed and attached. I think that it is good.
Since the STAINLESS-STEEL part melted when the Motorcycle cover was hung, it processed and attached.
I think that it is good.
View detail
Fits: KAWASAKI D tracker, KAWASAKI D-TRACKER-X, SUZUKI DR250R, KAWASAKI KLX250
Although 40 to 43 mm was purchased, it has bound tight and done to the extent that the pillar form of Clamp both ends hits. The service information of this was not found -- For the moment, exhaust leakage is nothing. If you buy the next also w
Although 40 to 43 mm was purchased, it has bound tight and done to the extent that the pillar form of Clamp both ends hits.
The service information of this was not found --
For the moment,
exhaust leakage is nothing.
If you buy the next also with
, 36 to 39 mm will be used.
View detail
New car purchase was carried out and GASGAS EC250 was attached instantly. attachment is easy, and if form is carefully decided according to the Chamber, it will be considerably finished in a Beauty. Are not just going to go until the worried po
New car purchase was carried out and GASGAS EC250 was attached instantly.
attachment is easy, and if form is carefully decided according to the Chamber, it will be considerably finished in a Beauty.
Are not just going to go until the worried point is a little short and it is said fully that an expansion chamber is covered, but I think that it is satisfactory practically.
I think that it is one precious point since the goods of other Manufacturers are being lost to reduction of
2 strike.
View detail
Fits: YAMAHA XT250X, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200, YAMAHA XG250 TRICKER, YAMAHA SEROW225 WE, YAMAHA SEROW250, YAMAHA SEROW225S, YAMAHA SEROW225 W, YAMAHA SEROW225
It was used when attaching Barrel 4 of DELTA to a SEROW250. Since in the case of the SEROW a Gasket is attached to a Normal silencer and it Says, this is removed and reuse is difficult. It is easier in the case of NORMAL return to leave ra
It was used when attaching Barrel 4 of DELTA to a SEROW250.
Since in the case of the
SEROW a Gasket is attached to a Normal silencer and it
Says, this is removed and reuse is difficult.
It is easier in the case of NORMAL return to leave rather.
although it is almost equivalent in
(although not returned)
thing being pure -- the Barrel 4 side side and the Exhaust-pipe side --
-- it was slow.
(Individual specificity ?)
Since there seemed to be no problem when fastening, but it was a sense and it hard to work,
heat-resistant Gasket was applied thinly and it fixed.
There is no exhaust leakage as a result of
.
It is although it is natural and becomes empty.
View detail
Fits: KAWASAKI D tracker, KAWASAKI D-TRACKER-X, SUZUKI DR250R, KAWASAKI KLX250
In DRC products, I think that it is what can be used. since structure is also solid, it is satisfactory -- it is .
In DRC products, I think that it is what can be used. since structure is also solid, it is satisfactory -- it is . View detail
[Webike Monitor] Since VFR800 tended to have deleted an Exhaust pipe when it fell on the right (it was actually able to delete), it equipped with it. It was good to also hide a crack although it was slightly thin and uncertain touch. The
[Webike Monitor] Since
VFR800 tended to have deleted an Exhaust pipe when it fell on the right (it was actually able to delete), it equipped with it.
It was good to also hide a crack although it was slightly thin and uncertain touch.
The
effect is not known unless it falls (smile).
View detail
It was used having painted black. Since there was not Colet until now, the heel portion of boots melted with the heat of the muffler, and removing took time very much, but problem solving was carried out by equipping with this. I think that it was
It was used having painted black.
Since there was not Colet until now, the heel portion of boots melted with the heat of the muffler, and removing took time very much, but problem solving was carried out by equipping with this.
I think that it was good shopping since the design was also pleasing.
View detail
It purchased for the purpose of the dress-up up to XR230. Since the pipe of XR was overflowed as it was, although the sanding machine ? cut, it can be processed easily and was very easy to attach. Since a parenthesis is good although greater impor
It purchased for the purpose of the dress-up up to XR230.
Since the pipe of XR was overflowed as it was, although the sanding machine ? cut, it can be processed easily and was very easy to attach.
Since a parenthesis is good although greater importance was attached than to stepping stone prevention to appearance for the dress-up purpose up, it is very much satisfied.
View detail