Reviews
Fits: KAWASAKI ZEPHYRX, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR1100
Not Copy, not OEM.
The price was a little higher than the OEM Catalogue, and when I thought it might be OEM, I received the OEM Product number 23037-1278.
In other words, it is OEM itself. There is nothing special about it.
Well, there's no doubt about the quality, but it's kind of a subtle unconvincing feeling……
This ZEPHYR Type Blinker is shared with ESTRELLA, Eliminator, VULCAN400 and so on. (Although the shape of Case is a little different) It's convenient because you can use it as is.
View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS), KAWASAKI Z1 (900SUPER4)
Suitable for Processing Base
I modified the License Plate Bracket to be able to mount the License Plate lying down.The price of used OEMTail lens base has been rising. These RiproParts are useful for processing. View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI S1C, KAWASAKI S1B, KAWASAKI S1A, KAWASAKI KH500, KAWASAKI KH400, KAWASAKI KH250, KAWASAKI H2C, KAWASAKI H2B, KAWASAKI H1F, KAWASAKI H1E, KAWASAKI H1D, KAWASAKI S3, KAWASAKI S2A, KAWASAKI S3A, KAWASAKI W1SA, KAWASAKI W3, KAWASAKI Z1, KAWASAKI Z1000, KAWASAKI Z750
Ideal for Custom base
Used on KawasakiZ1.
I used it for the Base of Blinker Bracket's super shortening.
The quality of Blinker Bracket is good in RiproManufacturer.
The texture of the Plating and the shape of the Bracket is at least better than the one of P company.
I cut the Short Bracket by 1cm more.
This is a handy custom parts.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RSCafe, KAWASAKI Z900RS, KAWASAKI Z900RSCafe
Head lampBracket and Quantity:Set to replace it
[How is it used?
Dress-upCustom daily use
Was the one you received as per Image?
Meter angle was different from Image.
Was the installation difficult?
The OEMMeter&Head lampBracket can be removed by removing the wires from the Caliper and the Master. It is recommended to install head lamp brackets of the same manufacturer at the same time, but it is complicated to remove the fork, align the brackets, and consider the interference with the body of each bracket.
How was your experience with it?
For all the hard work I put in, I feel like there's not much change in appearance. (I'm actually up about 40mm).
[Included Parts:were they on?
No. Bolt is OEM.
[Was there anything that disappointed you?
As stated above, there is little change in appearance.
Other items that would be helpful
Point and hang of installation/Anyway, prepare in advance.
The Meter Bracket itself is easy to install.
Note:If you use the company's Head lampBracket, you will have to do more work.
Items you should buy together/Head lampBracket
There is not enough room to install the parts without interfering or machining the long holes because it is a newly developed part.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS
Along with the Blinker replacement.
When I replaced OEM Blinker with external Blinker, Relay capacity was not enough or it didn't blink, so I also replaced Relay.
I chose this product DOREMI because it was available for my car model. It is working without any problems.
View detail
It takes a lot of work, but it's fun.
Initial ModelC1ZEPHYR750OrSeeder and regulator wiring is degraded contact burned to purchase junction box ICIgniter and Tail, it was difficult to enter the connector and it was difficult to do. In addition, it is not the Bullet Terminal but the Crimped Connecting Terminal with Shrinkable Tube when processing and wiring to the existing Coupler. (0.3 to 1.25) In the event that you have any questions regarding where and the best way to get in touch with us, please do not hesitate to contact us. I replaced it with a Switch. View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI W3/650RS, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z750 (air-cooled), KAWASAKI Z750 (air-cooled), KAWASAKI Z750-D1 (KZ750D), KAWASAKI Z750FX, KAWASAKI Z900 (KZ900)
Order Cancellation
My name is Hoshino.
Order No. W210301A2072
View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI 500SS MACHIII (H1), KAWASAKI H2, KAWASAKI W1 S/SA, KAWASAKI W3/650RS, KAWASAKI Z1 (900SUPER4), KAWASAKI Z400 (KZ), KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYRX
Half the price of OEM is attractive
The Blinker was damaged by a fall, so I bought it. OEM is also sold, but I was attracted by the cheapness and decided to buy DOREMI. The appearance is the same as OEM, but the inside is different from OEM as shown in the picture. I like it because it is cheap, but it is not suitable for people who are particular about it. View detail
Tail lamp
PMCLong tail extension kit
Long Bolt
View detail
DOREMI 6V MONKEY/GORILLA Main Harness
ZEPHYR750 Initial Model 6V MONKEY/GORILLA Main Harness has been discontinued, so I bought this one.
It's a quick and easy install with nothing standing in the way of installation.
Because the coupler of wiring is different in some places, it is necessary to remove the original coupler and use it, or to connect it with Bullet Terminal.
I'm not an OEM, so I'm not sure if this is something I can do.
Processing may seem difficult for those who have never done it before, but if you've done it before, it's easy to do.
View detail
Fits: KAWASAKI H2, KAWASAKI 350SS Mach II (S2), KAWASAKI 250SS Mach I (S1), KAWASAKI H2, KAWASAKI 350SS Mach II (S2), KAWASAKI 250SS Mach I (S1)
Indicator stems
Really great part. Well made and superbly chromed. I hate long indicator stems and these short ones - that were only made for the Japan Models are perfect for me. View detail
Fits: KAWASAKI ZEPHYR1100, KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS), KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYRX
If you want a Z2Type tail lamp, I recommend it.
I installed it on my ZEPHYR1100.
The manufacturer's price setting is similar to any manufacturer's, but Reflector is also attached, and I chose it because it is called Japanese Vehicle Inspection Correspondence.
The installation difficulty level is as it appears. It would be easier if you bought the Exclusive Bracket from another company, but I bought the Bracket from Home Center and installed it.
View detail
Fits: KAWASAKI H2, KAWASAKI 750SS MACHIV (H2), KAWASAKI 500SS MACHIII (H1), KAWASAKI 500SS MACHIII (H1)
previous order
I think these might fit my s1 250 but i havnt recieved previous order. so not sure about ordering these regards Ian hiscox View detail
It will last for a long time
I chose Halogen because I didn't like the lack of a solid light axis.
It doesn't have the white or loudness of the LEDs, but I think the Halogen is the best way to see the road surface conditions when driving at night.
View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI Z1 (900SUPER4)
Look good!
I installed the Z2 meter on KZ750D1 and replaced the Stem with PMC Z2 meter (If you don't want to replace the Stem, you can do it by modifying the meter bracket (If you don't replace the stems, you can process the meter bracket I don't know about meter error, etc., but there's no needle blur The meter is visible while driving, so the racing meter is good for those who are visually inclined It may be If it is possible, I would like to use White for Panel ^^ View detail
Fits: KAWASAKI ZEPHYR1100, KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS), KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYRX
z2Tail lamp
Without saying it, the Z2Tail lamp looks great on the ZEPHYR
You will need to fix it in place with Star or something like that as it doesn't normally stick
I bought a z2Tail lamp mounting kit for my ZEPHYR750 and put it on
Bullet Terminal bought a Coupler of the same shape as the OEM and replaced it with Couplet-on
The Z2Tail lamp rusts and I wish there was one that doesn't rust
View detail
The 6V MONKEY/GORILLA Main Harness exchange was a Large oddity
6V MONKEY/GORILLA Main Harness Exchange is Instruction The Manual states Single-vehicle BodyManufacturer issued Service Manual as a basic and reliable We do it better than a PRO Mechanic with the knowledge and skills to do it It's not a good idea So when you install it by yourself, please do so at your own risk As for me, there is no official Kawasaki Motorcycle shop near me, so I talked to my favorite shop once I was told that it would be tough to do the installation myself (This is because I was worried about short ignition from the deterioration over time because a part of the connector was burnt Moreover, I will leave the contents of this exchange as data in this Preview so that I do not forget the contents of this exchange.) I'm sure there are some incorrect statements, so I hope you can see this as a moderate reference
These are Harness replacement parts for C1 to C3 If you want to refurbish after C4, you must get the Maintenance Manual It is dangerous to confirm only with the original due to the subtle change in wiring diagram Especially the one who has not done it, because the ignition accident by Seat is a mistake of wiring and the ignition accident by Seat becomes the origin !!!
advantage
LeftHand and LightHandS/W could be connected as it is
Tachometer/Speedometer/Neutral/Light No Connector changes
No change in Junction Box/IC Igniter's Connector
It is a bundle of Wiring, so the protection Tape is also firmed up as a protection of Wiring It was a safe product
In almost the same colors of the original 6V MONKEY/GORILLA Main Harness Wiring It was usable as it was, with some color differences (Because of the mistake of 3 wirings of Front Blinker, the blinking became early I replaced it with a difference Wiring and returned to normal blinking :)
This is an out-of-print item that is not produced by the manufacturer and is out of print, used 6v monkey/ If you buy a GORILLA Main Harness, the time lapse is the same, so I knew it would degrade over time I'm afraid, I'm handling it because Wiring is too time consuming to create from scratch by myself Good product
After replacing the 6V MONKEY/GORILLA Main Harness, the Engine's start will be The car started up more consistently and quickly than before the changeover, and I also pulled the chalk and adjusted it in the summer, but this is not the case The adjustment time has been reduced
(Speed to RPM is unchanged My motorcycle averages about 3700 Engine rpm at 80 km/h It is)
It is set before the exchange of 6V MONKEY/GORILLA Main Harness since it is a carburetor, it is breathing funny after the replacement I may need to adjust the carburetor again (It's just a feeling I've felt.)
This is a sensory experience, but when I'm on a motorcycle, I'm in a good state of mind I think you can sense whether it's a bad condition or not After the replacement, the electrical system is now in a better condition than I was expecting when I was driving the motorcycle It gave me a sense of security about driving
Disadvantage (It's a change, not a flaw.)
When removing or setting up 6V MONKEY/GORILLA Main Harness Small holes behind the MainLight, this one is one at a time Wiring The connector can be removed and the Wiring can be pulled out The space between the front rooms of the GEAR v Letter is too narrow (Quantity:Pair (for Left and Right) ). forcing the front chamber of the carburetor to be removed when the Air Fruter's enclosure is removed There is no choice but to remove or insert the Connector, so if the wire is broken or the Connector is damaged Caution
The Instruction Manual should be shrunk to a slightly larger size than A4 paper The Wiring diagram which is in the housing is described by the letter where housing is exchanged only by this If it is not exchanged for various reasons, it is not a motorcycle The people who are desperate to have a working system are troubled by the fact that they can't move I couldn't imagine what kind of situation it would be in if I didn't try it
Purchase and install Housing of No2 H4 separately (Gi Positive is still intact, and another Wiring out of H4Housing with Gi Hoj When a white surface product is released in the light system, it can be replaced with a new one as it is It is) I don't use LED wiring because I like Halogen
The 6 V MONKEY/GORILLA Main is located near the root of the Light to Handlebar Harnesses that extend beyond the Left to adjust the length of the Harnesses are protected by Tape only It is thin because it seems to be damaged by the friction between the Harness and the car body when operating the Handlebar Rubber cover is wrapped around it to protect it
No transparent protection cover for the Connector in the Regulator/LectiFireYa
Connects to the No3Alternator and the Rectifier/ Firewire3 since the pole is the same yellow color wire, when you plug it into the 3-pole connector, where do you put it? I don't know if you're going to connect (It's in the Corkter for 4-pole from the beginning, which makes it even more confusing!) The tester was used to check the current flow to the actual object installed (Alternator's 3-pole sold to Home Center for future things (Replaced with the 250 Connector that's in there)
Because the No4 Starter Relay is out of print, the Bullet I managed to unplug the terminal and port it (Because it is a Small Small Small Bullet Terminal, the ConnectorBody Beware of possible damage to the) If it's damaged, you can still connect it with the flat Bullet Terminal as it is I'm worried that it will come off
The No5 Tail's Connector is a 250 model which is sold at home center etc Housing3-poleQuantity:If you want to use it as it is, you can replace it with the Set, because the claw part was in the opposite position If you can't do it, please do it Also check the internal terminals for corrosion on the porting!)
No6 Kawasaki-specific specs, so the shape of the bullet terminal is different It is different in shape from the Bullet Terminal sold at the home center, and is a special Buy the Bullet Terminal separately or use Blinker for all Bullet It depends on whether you want to replace the terminal This time (FG-SS, Bullet Terminal Female, cylinder diameter 3mm, length 21mm) We have replaced it with
There is no resin cover for Neutral S/W, using the HeatTube that I had, the whole thing is I made a hole on one side and dealt with it And when fixing the cover of Engine with Screw, this Wiring was caught and the wire was broken Make sure you don't do this before you install it carefully, once it's in the same position as it was before it was removed It hit the gap of the cover of the Engine and broke the wiring Because the position of connectors and so on are different from the original, I thought it is the same work as usual I've done that
I didn't put the picture on this page, but the size of the battery's Plus+ is a little smaller It was a Gihosi terminal (If you look it up on Net, it's for bonders and it's a Hit.) It looks and feels like the same shape, so you wouldn't think it was a different Bullet Terminal at all during production I don't know, so if you can, I'd like to make sure that you get the Bullet Terminal and the other terminals installed before you receive the product It's a good idea to install the connector on the original bike and test it out with a temporary assembly It will take some time, but it's a good idea to take some photos and put them on your current bike I think the work would be easier if you were looking at things by comparing them to
All of the cutting wirings that have been replaced with new housing as much as possible have been soldered or have been cut I tried to reduce the electrical loss by eliminating the contacts as much as possible, but I was afraid of degradation and damage to the parts, so I tried to make each part as small as possible The spec. is set to Bullet Terminal for easy replacement
View detail
Fits: KAWASAKI Z900 (KZ900), KAWASAKI Z750-D1 (KZ750D), KAWASAKI Z750 (air-cooled), KAWASAKI Z750 (air-cooled), KAWASAKI Z10012VUniversal, KAWASAKI Z2 (750RS), KAWASAKI Z1000, KAWASAKI Z1 (900SUPER4)
Horn 12V 3A
This horn by Doremi Collection is a Nikko Horn. There are two sizes available : Large and Small. I bought the small horn and it is very good in fit and finish. The connector thimbles are also quite robust. It has a vintage style sound and is perfect for older classic Japanese motorcycles and on the newer Triumph twin motorcycles. The price is also very cheap considering similar horns are selling on eBay for twice the amount. Highly recommended!! View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI 500SS MACHIII (H1), KAWASAKI H2, KAWASAKI W1 S/SA, KAWASAKI W3/650RS, KAWASAKI Z1 (900SUPER4), KAWASAKI Z400 (KZ), KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYRX
It was good
I bought it because my OEM Blinker broke down due to age-related deterioration, and the OEM is over $5,000 and After much deliberation, I decided to go with DOREMI, which has a high review rating among the Reproducts I did I really like the look and feel of the OEM same texture The internal construction is different from the OEM as shown in the pictures, but I like this one better because it lights up beautifully I like it Just for Reproduct, it's in the OEM Lens STANLEY There is no engraving etc. on the product (If you're a stickler for the shape of the OEM, I think you should just make the Lens an OEM) and Because the inner diameter of the OEM bracket is narrow (about 2mm), the Bullet Terminal does not enter As a countermeasure, cut once from the root of Bullet Terminal, and set Wiring to I ran it through the Bracket and then again with the Electric Works Pliers in the picture You must install the Bullet Terminal View detail
Fast delivery and it works perfect
I needed to replace my GPz1100B2 fuel sensor and this particular part is an exact fit and works as expected. As an extra bonus it was delivered to Australia in 5 days with no customs hassles! View detail