Reviews
Compactness for any type of car
[How is it used?
The OEM tail lamp for the XTZ125 is an adaptation of one used on Yamaha road motorcycles (SRX, SDR, etc.) from the 1980s to 1990s, so it seems a bit large and compact for an XTZ with a raised tail. I wanted to replace it with something a little more compact, so I went to Webike and found this product.
Was the one you received as per Image?
To be honest, it is more Compact and thinner than I expected, and at first glance depending on the position setting. I think the Tail lamp isn't installed!" I thought it would be possible to do the same thing with the Image product. The product was more than Image.
Was the installation difficult?
If you remove the Connection Connector from the OEMTail lamp and connect it to each of them, the functional aspect of the Lamp is finished.
My XTZ125 had a Bullet Type Terminal, but the large size was not quite right, so I replaced the Bullet Terminal on the product side. One of the 3 wiring was Grounding Wire (Black) and one was Yellow and one was Red wiring with Tail & Stop-lamp and License Plate Light, but I can't remember which one is which... Sorry.
The only thing left to do was to fix it to the car body, but there was no good place to bolt it to the car body, so I used several tie bands to fasten it to the seat rail.
Drill a hole for the License Plate in the tongue (the black plastic part that hangs down at an angle) under the Lamp, fix the Number, and you are done.
The Blinker of XTZ is fixed to another part, so no special modification is required.
If you buy the OEM type connector for each manufacturer sold by KITACO and connect Wiring, Wiring will be refreshed and you can easily return to NORMAL. If you purchase the OEM type Connector for each Manufacturer sold by KITACO and connect Wiring, Wiring will be refreshed and you can easily return to NORMAL when you want to return.
How was your experience with it?
I fixed it in a safe position, because I might be involved in an unexpected accident such as a rear-end collision if the tail lamp is not clearly visible when driving on public roads.
[Included Parts:were they on?
This is all the product Body listed in Webike's product section. It is a very simple product.
[Was there anything that disappointed you?
Not at all.
I was concerned about the strength of the tongue portion, but there was no problem at all for just playing in the mountains.
Probably not Large sturdy unless you hit it directly.
Other items that would be helpful
Point and hang of installation
If you want to process Wiring as beautifully as OEM, use OEM Type Connector by Manufacturer as described above. (If you prefer Bullet Terminal, you can leave it as it is, but please perform Waterproof processing.)
[Availability and clarity of the Instruction Manual
I think it is an easy product to understand as an electrical system (?). I think it is an easy-to-understand product as
[Notes]
Nothing in particular, just be careful not to misplace Wiring.
[ITEMS TO BUY TOGETHER
As I mentioned above, this is also available from KITACO and other companies. OEM Type Connection Terminals by Manufacturer will allow one-touch connection to Harness on the car body side.
The method of fixing to the car body varies depending on the car model, so in some cases, the Bracketetc. may be folded, bent, or modified.
First, check the fixation method by placing it on the vehicle in which you want to install it.
[Opinions and requests to Manufacturer
Mine is Large sturdy, but my friend who installed the same product had several LED bulbs that did not glow in some areas. Please improve and stabilize the quality.
View detail
Fits: Others (AC-30-02)Cyclop Headlight, Others (AC-30-01)Diamond Head light
Quantity:1pc., Size is about φ40~.
I got this for Replacement for CyBlack Ops.
It's rubbery and thick like the Tire tube, and it seems to expand and contract in a certain way.
The inner diameter when naturally wrapped is about φ40, and it will be a bit of a pull to install on the Inverted Front Fork of the Off car.
On the other hand, the inner tube of the upright fork may be loose depending on the car model.
By the way, the price is for 1pc. (660 yen) 。Quantity:1 Set for 1 Vehicle is 2,640 yen……. You can buy a cheap headlight unit for the price of Gold that you can replace several times.
View detail
Good looks and high durability.
The KLX150BF has been in use for two years.
Basically, drill holes directly on Racer's PolymerFender and install it with Bolt & Nut. Product. I have made and installed the Bracket by myself, but it requires some skill to install it on a TRAIL vehicle.
The License Plate is also attached to the resin Fender via Bracket, but It seems to be strong enough. I run through the woods every weekend, and there is no sign of breaking. It's strong. The weight is light and the stop lamp is very bright.
View detail
ACERBIS X-LED PLATE Tail Light
The LED of TER light of ACERBIS used before was replaced with this because Left half was cut off. It is perfect for external Fender. However, because it is not a shape considering the installation of Blinker, I had a hard time installing Blinker. I like Design because it is ◎.
View detail
It purchases for an Appeal in a front face. Although I think that quantity of light is enough, since the gap of each LED is larger, it is the touch in which it is better to call it six LED rather than the Line of light. Although the problem of manag
It purchases for an Appeal in a front face.
Although I think that
quantity of light is enough, since the gap of each LED is larger, it is the touch in which it is better to call it six LED rather than the Line of light.
Although the problem of management of a power cord has
attachment, a Fitting is not bad in general.
But since a coiled power cord like the code of a telephone currently attached did not have so very well appearance, it cut with the root and changed into the electric wire prepared on its own account after it.
Although
structure top waterproofness is not [ high ] so, and it ran also in the inside of the heavy rain several times, for the moment, it is not hit by Troubles, such as fault current and failure.
But since the Fuse is not attached, it is necessary to prepare the fault current worries direction by oneself.
In the direction where a wearing person wants to make little Dual-road Hand guard into a Maniac further primarily, it is recommended.
View detail
[Webike Monitor] It is used in order to make CRF 100F into public road specification. Very satisfactory, since a Rear fender is well suited as ordered. attachment Screw is for [ which is fundamentally made somehow in gauging although it is at
[Webike Monitor] It is used in order to make
CRF 100F into public road specification.
Very satisfactory, since a Rear fender is well suited as ordered.
attachment Screw is for [ which is fundamentally made somehow in gauging although it is attached once ] persons.
View detail
Fits: Others (AC-30-02)Cyclop Headlight, Others (AC-30-01)Diamond Head light
It is used for KL250R. Since the diameter of Faulk is too small, the rubber board would be bound on the opposite lap, and also it will take. Since it will be satisfactory if the front mask made from ACERBIS is used, but the hole by the side of a m
It is used for KL250R.
Since the diameter of Faulk is too small, the rubber board would be bound on the opposite lap, and also it will take.
Since it will be satisfactory if the front mask made from ACERBIS is used, but the hole by the side of a mask is too large for using it for a used XLR front mask, after letting a strap pass on a mask, it is necessary to make a washer etc. blow.
As for a washer, M10 is the best.
Compared with the stay of normal, removal is easy, it also becomes a weight saving of the circumference of a front above all, and the circumference of a handle becomes light.
View detail
The whole stay was removed with the pure mudguard of XR250, and fixed attachment was directly carried out on three attached screws at the fender. Appearance is very good, is felt refreshed and also becomes a weight saving. The visibility of a tail
The whole stay was removed with the pure mudguard of XR250, and fixed attachment was directly carried out on three attached screws at the fender.
Appearance is very good, is felt refreshed and also becomes a weight saving.
The visibility of a tail lamp merely gets extremely bad.
Moreover, it will not be attached to a main part if the fitting hole of a number is also a regular location.
I used the hole on the right-hand side of a number as it was, and it punctured left-hand side to the number itself.
Although attached in the state where it offset on the left, since the right has a silencer, it is comfortable, and I think that it is good.
View detail
It is a lightweight compact anyway. although it is made to hit here and there violently fairly, there is no sign of breaking -- ! -- however ... since it is too compact, it being able to equip, if the number for mopeds does not carry out stay creation
It is a lightweight compact anyway.
although it is made to hit here and there violently fairly, there is no sign of breaking -- ! -- however ... since it is too compact, it being able to equip, if the number for mopeds does not carry out stay creation, either, and standard wiring are too thin, and somewhat uneasy.
View detail