Reviews
Fits: SUZUKI SV650 N, SUZUKI DL 650 XT V-Strom, SUZUKI DL 650 V-Strom
The CP is also good.
From the name PyramidPlastic, I was prepared to order some more cheap products.
In fact, the FRPParts arrived with a high degree of precision, which is quite high for exterior Parts from overseas.
The bracket engages the Crankcase Bolt firmly, and the engagement with the FRP part is not bad.
However, the supplied Bolt is a bit short, so you may want to prepare a Bolt of about +5mm.
It is not impossible to stick to FRP, but it does not put a load on FRP, and above all, it increases work efficiency by a large margin.
In fact, a separately purchased DesignBolt was used for installation.
I have the impression that it took quite a long time, but it is because it is an overseas parts.
Considering that the FRP parts are solid and cost only 20,000 yen, the cost performance is also good.
View detail
Need to be a little creative with Screwdome.
I bought it because there were few other options and I thought it would be better to buy it than to use it by trial and error and have more unnecessary parts.
The bracket for the Right Side is included, but when installed as per the screw holes, the pressure applied to the Fender feels unreasonable, so the existing holes in the bracket need to be widened with a drill or newly drilled to shift the fixing position with the Swing Arm.
Since the two holes on the Fender side do not match at the same time, only one hole was used and the unused hole was filled with black SiliconPate. However, it only takes 20 minutes to adjust the holes on the mounting bracket.
Item number as for FZS600 07214." When 07227. but if it is FZ400 compatible, 5DM series (Fazer 600 1998-2001) of 07214." becomes. 07227. is a 5RT system.
View detail
PYRAMID PLASTIC Seat Cowl for Yamaha MT10SP 2017
This was something I have been thinking of buying for quite a while now. Now I also have the comfort seat for the MT10SP, I thought now would be the time. I was pleasantly surprised that Webike stock quite a few different parts for the MT10 series. Even more impressed that they have the SP seat cowl in the same colours as the original bike has. I always have more than one item in my basket, ready for purchasing. This way, the shipping costs are spread out over all the items and you are not just paying a flat rate for one item. I used EMS fast service for this order and they are now my go to courier from Japan. They just work and get your order to you fast. 5 days from ordering is perfect for my needs. All the items in the box were well packaged, in their own OEM packets and along with bubble wrap and air pockets so there would be no damage in transit. Webike even tape the outer box edges so nothing can escape, be lost or be stolen. Everything arrived in tip top condition, no damage, not even the inner boxes were scraped. A painted cowl being scraped would be absoutley devastating. Not happening here from Webike. Perfect condition on all the parts in the order. Although it only serves a purpose to cover the seat part of the seat, it does it very well. The only niggle is there is a slight bit of touching of the bottom part. Nothing too serious but still, you would expect perfection from a part that is specifically made for the job. This is why I marked it down 1 star, 5 star is only deserved from 100% perfect. Nothing to do with Webike, it is Pyramid that made an error. I will contact them directly to see what they suggest. Pleased with the overall look, even though this is making me want to fix it myself. Thanks Webike for all your help View detail
Fits: KAWASAKI ZX10 R, KAWASAKI ZX636, KAWASAKI RSV1000 07-08
It will have a tightened appearance.
I installed this on an external single seat cowl for a GSX250R. It is for NINJA, so it doesn't fit perfectly, but it fits quite nicely. The product arrived more than 2 weeks earlier than expected and the quality of the Level is satisfactory. I don't feel the effect of TouringLevel, but I think it is possible because it makes the exterior look tighter. View detail
It works quite well.
Gold molds are not well made, or maybe it's because of Quantity:Pair (for Left and Right) is an unbalanced product, which I don't think is possible from Japan's point of view, but once it is installed, it is a Quantity:Pair (for Left and Right) The balance of the front wheels is not broken. The effect of preventing mud and water splashes from the front wheels is unexpectedly good, and the effect is very large. It is easy to install, and I am glad that I installed it. View detail
Compared to the cheaper one
P&AInternationalExtender I read the impressions of Fender and found the roughness of the molding to be noticeable and cheap, so I was prepared to be a human pillar and bought this one, which did not have any reviews.
The estimated shipping time for the WeBig was three weeks, but it took EXACTLY three weeks to arrive.
The contents included a FenderBody, a plastic Clip for drilling and fastening, and a Strong Double-sided Tape.
I didn't have the courage to drill holes in the Fender, so I fastened it with double-sided tape only.
The molding, which is of concern, is distorted as expected.
Quantity:Pair (for Left and Right) The upper part of both theQuantity:Pair (for Left and Right) It is not symmetrical.
It is not noticeable once installed, but it may bother some people.
Installation is also quite troublesome since the Front Fender has to be removed.
However, the head cover of the engine's cylinder was also dirty from the mud splashing on it, so we decided to put it on.
I haven't tried the effect yet, but I would like to check it then, as I will be stepping on puddles and gushing water if I drive on mountain roads sooner or later.
View detail
Fits: YAMAHA Tracer 700, YAMAHA Tracer 700, YAMAHA MT-07
It's better than nothing.
MT is made at low cost. I wish I could have at least put this on… View detail
Fits: YAMAHA MT09, YAMAHA FZ09
Just like the image!
The Magical Under Cowl is a little too large for my image, and other manufacturers are too angular, so I chose this one for its appearance.
I bought it on the assumption that it would be repainted&Bracket processing, because some of the earlier comments said that the bracket didn't fit or that the paint had a wound.
As a result, the paint was even and even, and although the bracket was partially rusted, no special modification was required. (Or rather, the accuracy was normal.)
The enclosed instruction manual was in black and I could not see it at all, and I did not know which screw to insert the bracket, so it took some time to install the bracket while matching it with the actual one.
This kind of Under Cowl is a decoration, so the effect will be Zero. But it is OK because it looks good.
By the way, the Exhaust System was not installed with Other Brand Product (SP Tadao), so I returned to OEM.
The instruction manual was useless and 1 pc of Screw was missing, so I gave it a -1 star.
View detail
something is different
I bought it to prevent scratches on the Waist Bag and because I have never seen anyone install it.
The installation was easy as I just used double-sided tape and stuck it on. It also prevents scratches perfectly.
View detail
Fits: HONDA CB 1100 RS, HONDA CB 1100 EX, HONDA CB 1100
Easy to clean, used on CB1100EX
Used for CB1100EX.
This is a model that has already been discontinued, and since it hasn't been popular in the past few years, there are very few parts available, so I bought this one.
The purpose was to fix the mud splashing on the exhaust pipe and engine area.
Even after cleaning up the exhaust pipe and engine, the length of the OEM front fender was getting dirty quickly.
After installation, the area that gets dirty became smaller, so cleaning became easier. Most of the dirt is concentrated in the lower part of the Engine.
I installed it with the supplied seal and screw. I did not install the screw because it requires drilling.
I did not have to worry about it coming off. However, I haven't driven 100km/h, so I'm not sure what will happen if I drive on the highway.
Of course, I cleaned and degreased it thoroughly before installation.
View detail
I like the way it looks.
The slimness is attractive because it is VTWINEngine, but I thought that it was a little lonely under the tank, so I felt that wearing Under Cowl would give it a sense of gravity.
But this is just my impression.
OIL replacement and Element replacement are also possible while the unit is installed.
This is a Large thing Point!
View detail
Easy to install, looks great!
The overall look is stylish and well made. Quintessential Made in Italy good looking.
However, there is a part where the making of the fixed part and the chain cover part is lenient, and I think that it is not possible to make it a little more cool.
It was thought that it was impossible to ask for the goodness of the making of the JAPAN article to a foreign product.
View detail
Nice installation
After the Fender Eliminator, if you have a stone splash on your back or Seat, or if the water bounces off your back I installed this in disgust because it made my back chatter
The volume feel in the back is up, and I like the look, a lot!
For the time being, there are no more stone splashes No more water splashes on my back
I did the installation myself
The Rear Axle Shaft must be removed and the Shaft must be inserted backwards
Also, the SprayGuard mounting part doubles as an ASKULBlock, so 1pc. is not required It becomes unnecessary
If you're not sure, it's best to have a motorcycle shop install it
View detail
It's unquestionably cool!
It's installed on a 2018 MT-09SP
A good price, but it's a good looking product for it
About the appearance
I was wearing a screen made by another company until I purchased this product, but I just couldn't I was looking for a more Sharp product because it would have a wild look to it
I really like this one because it's Sports like Styling in that respect
Combined with the design, it's probably not an exaggeration to say that it's an OEM (Lol)
About the texture
Many people may be concerned about this place because it's an international product
Personally, I don't have a problem with it at all
Reverse side as shown in the third picture (Ruff?) is a bit BALI-esque, but I don't mind it at all
The surface is perfectly clean!
About wind protection
It's in the name of the product as Screen, but it's Cowl
Don't expect the wind protection to be effective
But.. "Run the Circuit! And "Fast and frequent! Unless you're the kind of person who says, "I don't have to worry about that at all!
View detail
A great sense of togetherness
The included Double-sided Tape" which combines geometric shapes; StickFit" is super strong To install it, you'll need some DIY skills to be able to use at least Drill It's also possible to attach it by StickFit alone without drilling any holes, but it lasts nicely and permanently If you're going to let me do this, I'd still like to unload the OEM Fender from the body and use the included plastic Rivet to make it work It should be installed The drill bit needed is 4mm, and it was fixed firmly as if it was integrated The shape is also very natural. The manufacturer's published installation video (https://) shows the installation in action www.youtube.com/watch?v=Zb9sf9KeTRs is a working video of the manufacturer's installation It helped me to grab the Image
Edge treatment is a bit messy so I used Sandpaper to prepare it. brakeHose clip back nails The indentations for the release were machined into holes for ease of maintenance after installation
View detail
Fits: SUZUKI GSF1250, SUZUKI GSF650, SUZUKI GSX650 F
No more rear box mud splash
Even though it's a sunny day for touring, I don't want to get the underside of my rear box dirty in the tunnel or on the mountain roads I put it on the
I can now run comfortably
I just asked my wife how much it looked like and she said $500!
But it's a product that Japan doesn't have, so I don't have a choice
View detail
It's okay
I posted the installation process in my diary, but I think the accuracy is good However, unless you have the ability to work on it to some extent, you may need to do some Fender detachment and drilling I think Hurdle is expensive I was worried until I got a temporary fitment because the product image is a completely different car model I contacted We-Big about this before I bought the car and they confirmed that it was installed I don't know because I don't have one," was the answer Isn't this answer a bit harsh? View detail
I like it a lot
I bought it in 2003 and it's still in use
Because it is expensive to use the 7RR's to make a Single Seat, Single Seat To make it wind
I think the costumes are high
The lines of color and so on are natural from a distance (from up close, there are steps due to the shape) I don't feel any problems
However, the treatment of the ura is a bit lax, which is a charm
I have changed the description of the vehicle with one passenger and will not remove it at the time of inspection
View detail
Texture ◎ presence ◎
The installation parts (Bracketetc. ), Except when I was looking for an integrated Rear Fender, I found this item and purchased it.
Though things are FRPMaterial, it is thick and very solid. The painting of Lime green was somewhat older people's color but we are generally satisfied.
Regarding installation, I asked Shop, but the installation itself was not difficult but it was quite difficult to get out the center, adjusted Bolt's Screw hole - - - I did it with.
Anyway, I am very satisfied with the presence.
View detail
Fits: YAMAHA MT09, YAMAHA FZ09
It looks good
There is no hole against Bracket and the painting has scratches etc. Product accuracy does not match the domestic product at all. Moreover, if the Exhaust System is set to Other Company Product, the Exhaust pipe part will interfere and it will not be processed unless. By the way, I have attached the full exhaust system of kFACTORY. Besides Design was good and none. View detail