Reviews
If you are looking for LED Blinker, this is the one.
It comes with a conversion connector so I can just replace the OEM blinker relay and not have a high flasher. View detail
Ideal for NAKED's Engine area!
As per the Title, it is ideal for cleaning around the Engine of Naked motorcycle!
I have been driving a GSX1400 motorcycle for 16 years. The front side of the engine is hard to clean because of the oil cooler, exhaust pipe, oil line, and oil filter, and I have half given up on cleaning it.
However, I didn't want to leave it like this, so I was looking for something better and found this.
I purchased this product expecting it to work as well as it looked, but it was even better than it looked!
The size is a little large and the core wire is hard, but that is good!
A 1400cc straight-4 Engine is wide, and being wide means that it takes a certain amount of force to shove Brush into it and scrub it.
LargeSize and hard core were exactly Exactly for my use.
Also, the core Wire is not very thick, so it will properly fit into the gap.
After washing the car using DAYTONA's Shampoo in combination with this, Engine has regained the beauty of its original black paint!
This is highly recommended for those who want to keep Naked motorcycle's Engine appearance beautiful!
View detail
Almost a must-have product
[How is it used?
I use it every day.
Was the one you received as per Image?
Yes
Was the installation difficult?
I think anyone can do it with Hexagonal Wrench, so I think it's a level of difficulty that anyone can do.
How was your experience with it?
I would recommend this product to all Eliminator riders, as the OEM was difficult to use and some helmets could not even be applied.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
If you have taken delivery of an Eliminator, I think you should buy it first, it is inexpensive and easy to install.
View detail
Reduced vibration sensation
Replaced from YB125SP OEM.
With OEM, we replaced it with this Clip to deal with the vibration when the Speed continues over 60km.
It is comfortable to the touch even with bare hands and does not slide around too much even with gloves, so it is very easy to use.
The crucial vibration is also clearly reduced compared to the OEM, and the effect is likely to be felt even during long hours of touring.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
Purchased for Loading Hook
I purchased this for the installation of the Loading Hook.
I may replace the Blinker sooner or later, so I need one with Service hole.
It is well made
View detail
It is moderately small and good!
It is moderately small and suitable for mounting on NumberSIDE. View detail
![[Highsider] Turn Signal Proton TWO](https://img.webike-cdn.net/catalogue/images/129660/17308_TS.jpg)
Small and wonderful.
Blinker is better for Small. View detail
tw200
[How is it used?
Touring
Was the one you received as per Image?
yes
How was your experience with it?
good
[Points to note]
None
How did it compare to other products?
good
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Purchased to install a BOX.
Installation is easy if you follow the instruction manual, and the helmet holder is also included. View detail
The variety was small at first.
I bought this product because I really disliked the NORMAL, mossy Fender. The length and width of the Fender was designed to be Refreshing for the two types of Fenders. View detail
Wouldn't this be the perfect maintenanceSTAND for Middle motorcycle!
I am satisfied with the stability of the vehicle when using the rear stand, the lightness when lifting up, and the price. I was thinking of replacing the tires by myself in the future, and I am also hoping to expand the range of maintenance of other parts. (The Z650RS weighs 188kg *Rear Carrier would be better) It only requires a little weight by hand. It is very convenient because I used to do one side lift up with a piece of wood.
Comparisons were made with Company S, Company A, and Company J. As a result, we decided on DAYTONA. As the reason for the selection, I considered that the structure of the most load-bearing part is Square Type, which seems to be sturdy, and that it is superior in terms of comparative cost. Also, the fact that the product introduction image is of RS was a deciding factor. The other 3 companies are all sold separately, and S and A are a little cheaper than DAYTONA, but there were some comments that the stability of the frame is not so good. I have not actually used them, so I am not sure.
The Stand Hook holder is specified to have a diameter of 14 to 18mm. If the diameter is larger than this, it will not fit in the attachment. Also, it takes a little getting used to inserting the Attachment.
The only drawback is that the latch of the U-shaped attachment is too thin and I am not sure if it is durable. I am not sure if it is durable or not. I don't know because I haven't used it yet. However, spare parts are available, so there is no need to worry. (This is not a problem for those who can weld.)
J company claimed that the handlebar should be set to "Left" and "Up" when the brake is "STAND-UP", while DAYTONA company claimed that the handlebar should be set to "Straight". I am not sure of the difference, but I found that the fixation of the hook of the front brake at the time of OthersLift up was the same in all companies. I hope this is of some help.
View detail
Red is good for Motorcycle's Accent.
My local Motorcycle store only had Black, so I purchased Red and was able to install it and am happy with it. View detail
Expected
I bought it for its looks and functionality, but there was an unexpected byproduct.
I have been using a Motorcycle Cover and have often caught the Mirror when removing the Cover. This Mirror is a fixed type, so it does not gap even if it is caught. At first I was annoyed that I had to use a tool to adjust the Mirror, but I personally like the fact that it does not move once the Mirror position is set.
The product is well made and can be recommendation.
View detail
It did not require much force to turn.
Used for YAMAHA's MT-07 (vehicle weight:184kg)
Adjust length to Swing Arm then Quantity:Set
I wondered if I would need to use a lot of force to turn the Tire when it finally lifts up. I actually tried it, thinking that it might take a lot of strength to lift the tire at the end, but it went up surprisingly easily. I think that even a woman with a small grip can turn it without a driver.
After lifting, even if lock nut is not used, it will not fall down, but it may be better to use lock nut to protect the threads.
Chain cleaning and wheel cleaning became very easy.
It is a cosmetic Tool.
It would be better to apply raspene or similar to the Screw pile when finished using it.
View detail
It can be used without problems
I used it to tighten the Stem Nut on my Motorcycle during the Restore process, I used it on a Plate type Torque wrench and was satisfied with the Torque management without any problems. View detail
Better than the standard metal pegs most tents come equipped with.
Considering the price being what it is, these pegs are accordingly of high quality construction & light weight. Their shape does seem to help keep them in place once driven in, they don't seem eager to come out on their own. Overall a really nice product. View detail
Better than basic tent pegs
Nice shape & light weight, far better than standard pegs at staying in the ground & of course they won't bend if driven in hard. Worth the price. View detail
I will not shake.
I used to have a ZMirror from Mukawa, but when I was having trouble with the blurred mirror surface, I found out about this one and bought it.
The back of the car can now be seen clearly.
Mirror is also slightly colored and looks luxurious.
View detail
Stem wrench, this is all you need
[How is it used?
The XR230 Stem has a bad habit of coming loose, so I tighten it up regularly with this.
So far I have not had any problems using it.
It is very inexpensive, so it is convenient to keep one of these in your tool box.
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125 G8, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125SS, SUZUKI ADDRESSV125LIMITED
I don't have to forget to buy anything!
Quantity of O-rings at the Oil Filter, Drain Washer, Oil Filter, Oil Filter Cover, and Oil Inlet.:With this set and oil, you have everything you need except tools.
It is very convenient because I don't forget to buy parts.
View detail