Reviews
Too Large to use for Scooter
[How is it used?
I bought this for Scooter Oilfor replacement.
When changing oil in the center stand of PCX125, it is difficult because there is no space to place a saucer.
Was the one you received as per Image?
I bought a Large size, but it was larger than I expected.
The texture was very good, and it looked like it would last a long time.
How was your experience with it?
With the Center Stand in place, I was able to change the oil, but the space under the Scooter and the size of the Oil Pan were too large, and it felt cramped and difficult to do so.
I am still glad I bought it, but I think I should have bought the One sizeSmallest one, because it is also very expensive.
[Points to note]
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Quantity:2pc. Set eye
Last time, I bought 1pc. for trial, not bad to use, but not good for the selling price and the texture with the fabric.
However, the Quantity:2pc. It is more convenient to have a Set, so I bought more because the selling price was lower.
Would I have bought more if it had been at the normal selling price?
View detail
I'd use it if I had it.
The items are useful if they exist, but they are useful.
When kneeling, you do not have to put your feet directly on the ground, and when sitting on the ground, it feels reasonably comfortable to fold it up and sit on it.
It is not a revolutionarily convenient Level, but I don't think you will feel lost if you buy it anyway.
View detail
Well, it's Brass, so I don't blame you.
I purchased this product to remove rust from the exhaust pipes of the Exhaust System.
Compared to the cheap wooden Grip Brush sold at Home center and other places, the grip of the Gold attribute is thinner and easier to handle.
I used it on some stubborn rust, but it is a Brass Brush, so it was a little soft, and I felt that a Brush with a little more firmness would be better...but that's a matter of tool selection.
For heavy rust, I think Brush with a harder material would be better, but for light rust removal, I think it is sufficient.
View detail
MVAGUSTA
I used to use a Dan Ball to change the oil, but this product is very easy to use. View detail
I don't care what you do, but don't make it mandatory because it's too much work to think about every Title.
I want it.
The latest motorcycles have a lunch box right under the belly and there is almost no gap between the lunch box and the crankcase, so it's easy to get dirty when changing the oil.
That's where this product comes in. It's not so much...
It's handy to have, but honestly it's a bit expensive to actively win just to avoid getting dirty with OIL.
Or for when you're short on shipping.
View detail
All necessary tools are available.
I haven't used it yet, so I can't write about my impressions of it, but I felt it was a good product with all the necessary tools.
I used to reuse the plastic bottle to bleed the air, but I thought it was a good opportunity to buy a special product.
As I mentioned at the beginning of this article, I like the fact that it comes with everything you need to bleed the brake line, and the fact that it comes with a glasses wrench is also good because it saves you from having to buy more tools.
To be honest, I don't know about the texture until I use it, but I am concerned about cracks in the hose and tank because I am dealing with brake fluid that has the risk of damaging various materials due to the nature of the work of bleeding the brake line. However, I don't think it is necessary to take it so seriously because it is a problem if it is cleaned immediately after use.
In any case, I would like to determine in the future whether the Cost performance is good or bad in consideration of usability, time saving aspect and durability.
View detail
thick
[How is it used?
I bought it because I wanted a variety of Brushes anyway, as I have a strong desire to make Motorcycle a k example.
There are five of them for different purposes, so they are active in various SCENE.
Was the one you received as per Image?
There was no difference whatsoever from the picture on the product Page.
How was your experience with it?
The first thing I used was the Yellow color Brush.
Application is Caliper cleaning.
I used a detergent and CHALYCHALY to remove the carbon scum.
The Brass Brush is useful for cleaning the chain.
Since the motorcycle is stored outdoors, rust is inevitably noticeable on the chain.
In such a case, rubbing with a Brass Brush will remove the rust to some extent.
It is convenient because it is possible to use it in various ways though I am not able to use all Brush at present.
[Points to note]
Head part is thick...
When you want to get rid of the dirt in the deepest part of your body.
The roundness of the Head part of the Brush is often brilliantly disturbed by trapping.
Is that why it's so durable?
View detail
after a long time
It has been a while since I used it for brake fluid replacement and air venting along with brake hose replacement.
The tube is hardened and won't go in the hole, is the Tank itself hardened?
It's not something I use very often, and this was only the second time I've used it. Too bad.
This is a very nice product.
View detail
The size didn't fit.
I was going to use it as a fixture for Under Cowl, but the Size didn't work well because it didn't fit a bit.
The bracket on the receiving end was a bit large.
The performance of Fastener itself seems to be fine.
It would have been nice to know the detailed dimensions.
View detail
First time replacement
Brake is one of the most important safety components, so you should ask a PRO to replace the fluid for peace of mind However, I decided to challenge it in order to increase the maintenance kill Plastic bottle was also considered as a receptacle when removing the old Fluid, but it was not Air release Quantity with tools to lower Risk:Purchase Set
Because the clip that secures the hose and the bottle is loose and can easily pull out, it is not possible to use the I've replaced it with a stronger one, but … it's still going to pull out with a little bit better results Loose The accompanying Instruction Manual includes a series of work instructions with diagrams
Thanks to the pre-review of the replacement procedure before the job, the job was completed without any air biting There were no leaks from the Hose and the Bottle did not collapse, but the old Fluid and the new I chose a different color to distinguish between the fluids, but the hose was a transparent yellow So it was hard to understand the timings to switch between them
I took the bike out for a spin to see how well the Brake works after the changeover, and there were no problems None If you want to reduce risk and increase efficiency, you can install One-Way Valve might be a good idea
View detail
It makes air removal easier
I used it when I changed the brake hose of MT25
I don't think it's particularly necessary to replace the brake fluid alone, but this time the hose replacement and One-Way when air is mixed in with Caliper's Overhauletc It's easier to vent the air if you have Valve
View detail
I wish I had stud bolt removerSet of KTC...
I did not buy it with Webike, but when I got this Remover set I thought regretfully that the four Remolver internal Roller surfaces were rusted... It is a material with price, so we would like you to use ginger, rust resistant Material.
Stud bolt remover of KTC previously purchased had no rust... Is commonplace?... Also, compared to KTC Stud bolt remover, I think that Roller's play and backlash are many... I am worried whether it will definitely bite with this...
I wish I had turned to KTC's Stud bolt removerSet and got to regret it.
Mail-in is 12. Not 7. I think that it will be 5. (It does not matter if you use Adapter... )
View detail
Feel like either way
I tried buying thought that I thought as soon as possible because Brake fluid exchange of three Motorcycle is done by myself on a regular basis.
The structure is Material : It is a very simple combination of an iron ball which becomes a lid in the cylinder of Aluminum and Spring for pressing it.
I immediately tried using Fluid exchange. Although the exchanging method is done with the air bleed Pump of the syringe type and when the air is difficult to escape, it is done by Pumping of the Brake lever but it is certainly a check valve but it is because it was not used until now, I can work on Smooth even without it, so I felt it was difficult to do it again if extra things were added during Tube. After all, I used only the first one and removed the second and subsequent machines and worked.
If you are familiar it's not necessary Parts but if you are unfamiliar it might be benefited.
View detail
It became hard to spill.
Until now, Oil was received at the BOX of the pla, but when transferring to a separate container of waste oil processing, there were many cases that it spilled on Sheng Large, but the Oil pan with Nozzle got less coarse Was.
By the way, us Oil amount at ZrX 400 : 3. 2L (Remove Filter) is.
Products are 3. I use a 5L capacity item, but when I receive an Oil it will accumulate up to 3 to 4 centimeters from the top.
Even if you lift the product by receiving Oil as it is, the container is solid without deforming.
Just when we process waste oil, wide mouth like shochu Plastic bottle (4L) I moved it, but carrying it is regrettable that Nozzle does not fit in my mouth ,,, I expect it to improve without using a funnel.
View detail
no problem
I bought it for face lapping of Clutch cover.
If the condition is not bad Motorcycle, number 400 is recommended.
If it is a daily Maintenance cycle Cycle, I think that if you purchase it once, you will not need to purchase twice as long as it will last long.
When storing, I think that if you keep it clean with Parts cleaner, the performance will last at the next work.
View detail
Brake air bleed
I bought it for bleeding of Brake.
Because it became One way, the air did not come back, making it easy for one person to work.
As the price goes so far, the evaluation is 3.
View detail
Because the number of sheets is large, it is OK with one.
Because the number of sheets is large, Thickness Gauge is OK with one!
Although it is, I will become Large by that much.
If you buy a couple, it costs Cost an extra, and there is no help but ,,,
When choosing and using a thin Gauge, the remaining Gauge is large and heavy, so it is slightly hard to use.
Well not to mention it ,,,.
View detail
It uses for the gap adjustment at the tip of a Plug. Although pasteboard may be sufficient, the Gauge to which the Size was equal is as more useful as something. I think whether to interfere, even if it puts into tool box.
It uses for the gap adjustment at the tip of a Plug.
Although
pasteboard may be sufficient, the
Gauge to which the Size was equal is as more useful as something.
I think whether to interfere, even if it puts into
tool box.
View detail
[Webike Monitor] With the Brush of which possession is done, since washing of the place which extended far back was not completed, the long Type was purchased. I think that it can use very efficiently even if it washes using a Cleaner
[Webike Monitor] With the Brush of which
possession is done, since washing of the place which extended far back was not completed, the long Type was purchased.
I think that it can use very efficiently even if it washes using a Cleaner, since it is a chemical-resistant thing.
I think that one may be in a tool box since it is needed if compelled in many cases although seldom used usually [
].
View detail