Reviews
For terminals of 4.0sq cord for charge current
I bought a battered 900SS (900SL) and am Restore.
The harnesses are also in bad shape, so we cut and re-created the damaged parts of each section.
The very thick wire for the Starter motor and the carburetorTire wire connecting the Engine and Chassis are also deteriorating over time and are crumbling and falling apart.
The internal core wire was also corroded by moisture that had entered the wire and was spewing GreenBlue, so it was re-created.
After the terminals are crimped with Electric Works Pliers, solder is applied to the terminals for secure wiring, and these terminals are protected with Shrinkable Tubes to prevent shorts.
The tube is coated with an adhesive that melts when heated and shrinks to make it Completely Waterproof, preventing moisture from entering the cord through the terminals.
It also serves as a Cover for the terminals, so using different colors of this Shrinkable Tube (Red and Black) helps to prevent accidental wiring.
It is especially effective when used in the terminal section that conects directly to the Battery terminal.
Φ9.5 is quite thick for Motorcycle wiring, so there are not many uses for it, but it is ideal for terminal protection for Starter and Earth.
Although it is possible to purchase a similar product at a wiring store at a much lower price, considering the time and effort required to go there and the use of multiple mail order sites, I think it is most cost-effective for ordinary people to buy a DAYTONA product at Webike, even if it is a little more expensive.
View detail
for Replacement
Relay on headlight relay kit suddenly broke
Purchased two Relay replacements because it's not a Wiring problem.
The product is an ordinary product with no negatives or positives.
I replaced the Relay so I can use it safely for the time being.
View detail
Effective
I purchased this for a power supply for a Grip heater that is attached by wrapping it around.
In the summer, I remove the Grip heater, so I use this Connector for One-touch power supply.
The waterproof specification is safe and secure.
The terminals are small and can be damaged if you are not careful when crimping through wiring.
View detail
Cosmetic Items for DIY
[How is it used?
I purchased DAYTONA's Power Unit D-UNIT+ for my XJR400R.
In this process, the stag beetle terminals were modified to Round Type Terminals, and Heat Shrink Tubes were used for waterproofing and terminal protection.
How was your experience with it?
The product was easy to use.
I didn't have a heat gun, so I used a Chuckerman to apply heat, but the shrinkage was firm.
The quantity is so large that I don't think we will run out of it in the foreseeable future.
How did it compare to other products?
Some products are sold as a single item in 6cm increments, but this product is easy to use because you can cut it to any length you like. Also, the package itself plays the role of reel, so it is easy to store.
[Points to note]
It does not have a clear waterproof effect, so care should be taken where it is used.
Also, the shrinkage rate is not that high, so choose the Size according to the actual Wiring you will use.
One concern is that the package is larger than expected, making it somewhat bulky when stored.
View detail
Easy to use
[How is it used?
The Heat Shrink Tube I had on hand went somewhere, so I bought one.
I chose this product because it is a sizeφ3.2mm, which is often used in Wiring, has a length of 3m, and is relatively inexpensive.
How was your experience with it?
The required length can be taken out and used immediately.
Heat gun (or writer) The work can be done easily by anyone who has
Shrinkage is not a problem, and Wiring looks great, so I recommend it.
[Points to note]
What is ReelPackage? I was wondering, but you can use it without taking it out of Package.
I opened the Package once without understanding, but please be careful if you are going to use it in the future.
How did it compare to other products?
I've been using it for a while now. (probably Emon's). There was no particular difference between the two.
It is long enough for amateur DIYers, so it is nice to not have to worry about buying more.
【Review】
It is easy to use, long enough and cost-effective.
If you are processing Wiring yourself, you should have one to make your Wiring look better.
View detail
It uses, when changing the present blinker a hazard and with a position.
It uses, when changing the present blinker a hazard and with a position. View detail
Used in License Plate LightWiring of WR250X
I used it with License Plate LightWiring.
For WR, the Brown wire on the body side was Plus and the Black wire was Minus.
I used it in connection with Y's Gear's Fender Eliminator Kit.
It can be connected without damaging the Wiring on the vehicle side.
View detail
Daytona Blinker Connector
Blinker connector for turn signals from Daytona. I bought myself on YAMAHA YZF R1 RN12 05. Because I have a motorcycle of the American version, there is a turn signal connector for three contacts. In my original connectors, the hooks are broken. After replacing all the connectors, everything started to work well. View detail
Daytona Kawasaki
I bought myself a used Kawasaki motorcycle. After the purchase, after some time, the rear turn signal stopped working. After diagnostics, it turned out that the old owner tore off the connector on the right rear turn indicator after the accident. I had to order a new connector from Daytona. This is a great connector. It installs quickly and easily. It is very similar to the original one. I recommend this product. View detail
Waterproof!
Blinker was used to make Wiring around the Front of WR250X. I changed to this preventive coupler for safety reasons.
The point that the Coupler's insertion and removal of the Coupler itself is Large strange is a little Large. MinusPoint, but nothing beats safety.
View detail
Where you want to Waterproof!
It was used at the time of Number Plate conversion & rarr;Fog Lamp of WR250X. Around the Headlight & along with Number Plate conversion, Wiring is further rain and wind. It's safer to go Waterproof because you'll be exposed to it.
Since the coupler is larger than I thought, it is installed in the part where there is room for space. It's better.
View detail
YAMAHAConnector
The same thing as that of the OEM
Other Brand ProductIt's useful for attaching tail lamps and other products
Requires separate Crimp Tool from ConnectorCrimp
In the past, the OEM body side Connector was replaced with a Bullet Type Terminal If you have this, only Other Brand Product Light side will be It's easy to revert back to OEM because you can just replace it with the Connector
View detail
It always comes in handy
The DAYTONA Connectors are useful for DIY processing
This is also used to replace the MT-07's Blinker with an LED one
It's also important to be able to return to the original state, and most importantly, to ensure the same maintainability as the OEM I always prepare the Connector even if it costs Cost because it's easier to maintain later
1 point, it would be helpful if you could lower the unit price by selling TAB and receptacleRose if possible It is
View detail
Useful for OEM diversions
MT-07First Model Type with Second Type Model I used it to divert Headlight
PositionThe position sphere-bound Connector is different in the front and back periods, so this is a conversion I made Harness and sandwiched it between them
The easy availability of these things is helpful for DIYers who want to put them together nicely
View detail
Good
I but it because i want like to change the light of my motobike, but the original one is not suitable, so i buy this connector hope it can suitable for my bike. the codition is good. View detail
DAYTONA Blinker Connector 040 (3-poles)
I want to share a review of the purchased product. I bought 1 pair of connectors to repair the damaged wiring on the Yamaha R1. Installation was quick and without any difficulties. The quality of the goods is excellent, as is the case with the original parts. I will buy more and recommend it to everyone. Do not regret what you buy for your motorcycle. I wish the seller success and all the best. Thank you . View detail
3pin
Great quality, lots of packaging. I like. Thank you :) Excellent quality, lots of packing. I like that. Thanks :) View detail
’99 GSX1300R HAYABUSA for Blinker
We used it for processing Blinker's Connector so that it can be restored
We can use it without any problem
Since the diameter of the LED Blinker is thin, I made crimping + soldering just in case
View detail
DAYTONA KAWASAKI Blinker Connector Set
I bought two pairs of connectors to repair the damaged wiring of the direction indicators. The installation of the connectors passed quickly and without any difficulties. The quality of the goods is at an altitude. As it should be - this is the real Japanese quality. I recommend to all . Do not regret what you buy for your loyal friend (motorcycle). I wish the seller good luck and success. Thank you . View detail
WR 250 X Fender to Eliminator
I bought it because it was necessary for License Plate Light as I made WR 250X a Fender Eliminator.
Even if myself who is not good at fiddling with the electrical system, I gathered the information of the predecessors, confirmed well what I removed, I was able to install it while I was stupid ....
There are 8 parts in this product, but only 3 points are used for License Plate Light of WR 250X.
Male side Female side seems likely to be cheaper if it separates products, but I think that this is useless.
View detail