Reviews
Hard but strong!
It has a slit in it and you put the wiring inside, but it's just too hard! It is not flexible, so it is hard to put in and take out the wiring, and it is not easy to handle! However, this is one of its strong points and its durability is outstanding! I mainly use it to put together the ETC and sub-computer wiring inside the motorcycle! It is a recommendation because it is very useful if used in the right place at the right time! View detail
I used it for storage for my own Wiring blindfold.
Plus and Minus lines from Relay, which I made myself in NINJA.
Grip heater, YOSHIMURAProgress2Meter and USB power supply with Bullet Type Terminal
It is connected, but has been left bare until now.
I left it as it was because I basically don't ride on days when it rains,
I'm concerned about the Red Wiring glancing through the gap between the Cowl and Handlebar, and I'm not sure what to do with it.
I purchased this product to conceal and store the Bullet Terminal part.
6Quantity:The Large size was sufficient to hide the Bullet Type Terminal of Set+Alpha.
View detail
I used the precious Large caliber Type compared to the ACTIVE-made Type.
[How is it used?
Heat Shrink Tube was purchased to hold the heat resistant hose in place as the oil cooler hose of ACTIVE was covered with the heat resistant hose and converted to BlackHose.
I used the ACTIVE one at first, but I forgot to put the Shrinkable Tube through the Hose.
Was the one you received as per Image?
It was as shown in the Image, but the total length was 12cm/Quantity:It said "1 Set of 2pcs." so 6cm*Quantity:I thought it was 2pc but 12cm*Quantity:It was 1 Set of 2pcs.
Was the installation difficult?
It's easy. As you can see in the video, it can be threaded over the top of the fitting, and the length can be easily cut with scissors. Even if you don't have a heat gun, you can use a lighter or dryer for shrinkage.
How was your experience with it?
I have no complaints about its use.
The performance was comparable to that of ACTIVE products, and the shrinkage was Smooth.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Color is more Color than expected:Gray was strong.
I think I would have felt more comfortable if the Black color was a little stronger.
View detail
It's hard for me, I'm clumsy.
Purchased to use only Male on the Led License Lamp side. Female on the body side was not necessary.
However, Male's terminal Quantity:Crimp failed on 1 pc of the 2 pc, so no more Quantities other than the one I bought at WeBig.:I had to drive 1 Set to a supply store to purchase it.
The remainder is 4 Female terminals, Male1 pc, Female side CouplerQuantity:2pc. Set, TAB coupler1pc. and will be sent to Garbage bin.
It would be helpful if you could sell the terminals only.
Or it would be helpful to add one Plus terminal each for failure.
For a clumsy person like me (laughs)
But this is expensive.
View detail
Useful Goods of Wiring branch
Useful Goods to help you branch Wiring.
Simply pull up the claw on the Orange, insert the uncoated Wiring, and replace the claw on the Orange to complete the connection.
All plugged-in Wiring will be short-circuited.
No tools required, it's truly one-touch.
When it comes to branching the wiring, it is common to make a Y-shaped branch line with Bullet Terminal or to use Electra tap, but if there are many of them, the wiring will inevitably become ugly.
In addition, there is a part where it is not good in terms of reliability to use the Electra tap which clamps two or more wires to one terminal, but this product can be used at ease also in that aspect.
When you have secured the Attachment power supply by the Bach direct Relay, or you don't like to take the Earth of the retrofit electrical equipment by the body ground, and you want to wire directly to the BatteryMinus. (It's me.) It is especially recommended for
If you connect +Line from Relay and -Line from BatteryMinus to this 5P, you can secure the accessory power supply for 4 terminals which can be connected and disconnected by One-touch.
Also, this product is very small, so I think it is not so difficult to hide it.
The only thing you need to pay attention to is that it is not Waterproof Specification.
You need to set it up in a secluded place where it won't get wet, or use gum tape or something to protect it from water.
By the way, it is a very convenient article that even 400 yen/piece of DAYTONA price is totally possible, but the one of Large book WAGO Japan (I assume they look/function exactly the same). is available on Amaz◯n, and that one is roughly 1.5 times the price of Quantity:1 Set of 3pcs. (For 5P)
If you want to stick with DAYTONA, you can buy it from webike, but if you don't find any significance in it, you might be happy to check out WAGO Japan's stuff.
View detail
Items that neatly summarize Harness
I used it on my Yamaha Max star125.
I made it a bar handle, so you can see Wiring and Coupler, so I blindfolded them here.
It was pretty stuffy, but it fit in well.
It's a nice touch because it's going to be a good protection against the rain.
View detail
It is indispensable for the wiring process.
The Harness when wiring processing and the electric parts are installed by making by oneself can be bundled, and it is very convenient to be able to process. The Refreshing feeling and the NORMAL feeling of the appearance are good, and it becomes the finish that can be satisfied. View detail
Used in 790DUKE's Rear blinkerCoupler
Things work fine.
However, it is not possible to crimp cleanly with ordinary Electric Works Pliers.
2.You will need Electric Works Pliers that can caulk 0mm
View detail
Active in organizing wiring
Bullet TerminalWiring on the external meter is colorful and stands out I used it for the purpose of warding off the eyes and wiring organization and waterproofing
Wiring can be put together with Harness tape or self-adhering tape, but there are some defects You'll have to remove it every time you check your wiring, which is time-consuming
The ConnectorBoots cover allows you to simply slide it off, making it easy to check And there's no chance of the tape losing its adhesive power and rewinding
There are several sizes and the price is not too high, so it is useful for organizing wiring in prominent areas
View detail
As I thought
It was a product as I thought. There is no problem with installation and texture is perfect.
Cospa is satisfied well also in terms of price.
Image when I installed it on the car body just like I was satisfied without problems.
View detail
Used as Cover stop for Breather hose
I used it for installation of Breather by carburetor change. We rolled a heat resistant Cover on Breather hose and used this item for its exit.
It was quite ExactlySize, so it was Large strange to pass first, but Material : Because it is Rubber, I extended it before passing it and passed it smoothly.
I shrunk it with Dryer and used it. Truly a bit of a thing, just finishing both ends of Hose with this product makes the texture feel better at all.
View detail