Reviews
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
It slips and moves.
Used to attach the Smartphone Holder to the Pipe behind the Screen on the Honda 400X (2019) (with an additional Spacer that comes with the Smartphone Holder).
The size itself is just right, but the hard rubber makes it slippery, and even when the bolt is tightly tightened, it slips and moves. Therefore, I wrapped a thin double-sided tape around the pipe on the body side before installing the bolt, but it is not completely fixed because the outer side of the bolt also slides.
I'm considering replacing the Arm of the Holder with an aluminum spacer only for the type that is tightened with ZETA Bolt.
View detail
Higher height.
I bought this when the Autofocus on my previous iPhone 11Pro Camera broke.
Type VibrationControlDevice to be attached to existing Smartphone Holder3
Just Smartphone Holder3+ IH2100Rigid (25077) The pull-pull mechanism is about 20mm higher than that of the "M" and it shakes more when a smartphone is attached.
I think it can absorb a certain amount of vibration, but the increased height makes it look bad.
If I were to purchase an expensive SMARTMonitoretc. without a phone attached, I would be willing to purchase a used Android phone and use it with TetherRing.
View detail
Fragile Construction, bad quality plastic.
This item looks very promising in the pictures. I really liked the design. In reality It is very weak. It is made of a very weak type of plastic. I have seen cheap phone holders for 7usd that use better material. There are very important parts in this design that should be made of metal, but in this case those are made of thin plastic. From the outside It looks like the body is made of aluminum, but it is just a decorative sheet metal part. If I knew, I would not pay more than 12 usd for this product. On the other hand, the vibration damper doesn't seem to do much. The Handlebar clamp is made of aluminum, but because it is very thin, It looks like it will break if you tighten the screw too much. Don't use this holder on single cylinder bikes, because the damper is not effective enough. Be very careful when installing this product, because It is not made of strong material and it will break If you tighten the screws too much. It looks like It will not last much under the sun either. For 52usd I expected a sturdy well built phone holder. It doesn't look like it was made in japan because of the cheap quality. It is expensive, bulky and flimsy. Next time I will try with SP Connect. View detail
Plastic Parts are too fragile.
Material:Plastic Parts are too fragile.
It is not that the Bolt was tightened with stupid force or that a hard object was slammed against it, but the Plastic snapped off in the order of the claw on the top side that holds the phone in place, the Body side that holds the middle claw in place, and the middle claw, making it unusable within one year of purchase.
The composition of the plastic seems to be hard and brittle, and if the phone is put on and off many times, it seems to get fatigued and go badrill.
I think that if the composition of plastic is changed to something more tenacious, or if it is made of gold, the durability will be improved by a large margin.
I would like to see DAYTONA improve on this.
View detail
Difficulty in moving and fixing the slide part.
I installed it on the handlebar of my Z650, even though the area around the handlebar is narrow and small. It looks nice and simple, but when I installed it on my phone (Xperia5), I had to slide the fixing part, but the slide was not smooth and it was hard to install because it was caught. Also, the lever for fixing is hard and difficult to do. View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
Camera cracks. When the phone is not attached, it is noisy.
[How is it used?
It's a Other Brand ProductHandlebar with separate handle, but I didn't need to use Bracket.
Was the installation difficult?
It is easy to install because it belongs to Hexagon Wrench.
How was your experience with it?
The part that holds the phone is Material:If you don't have your phone on in Plastic, the vibration makes it noisy. I don't want to wear my phone when I'm going for a walk around the neighborhood, but I have to because of this.
When I think that the phone itself absorbs this vibration, it doesn't seem to be so good for the body of the phone, and in fact Camera was broken. (Android)
As a Smartphone Holder, it's affordable, and if you don't make a mistake, your phone won't fall off, but it's not very useful, and the plastic is cheap and makes the Handlebar look tacky.
If you're on a budget, you might want to spend a little more on a good Parenthesis.
[Included Parts:were they on?
It was all there.
Point and hang of installation
If you are using the OEM handlebar on the Ninja 400, you can either run the bracket through the Stem Nut or through the unused screw hole in the clutch lever.
I replaced the handle with SNIPER's Other Brand ProductSeparate handle, which has enough room for the handlebar width, so it can be installed without the bracket.
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
I think it's something like this
I purchased this to install my phone
I was able to install it without any problems, but the part that attaches to the multi-bar The Center of the PenetratingBolt receiver is confusing! There are such things as
I understand the same color Black, but I can change it
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
I also broke up..
I purchased it again because I purchased it before but it used 3 months not to use It was hung from the center just like before. I think that vibration countermeasure is insufficient rather than tightening Torque is it? Although I want to put in Objection this time, I think that there is no choice but to give up if there is a defect in the product. This item is not recommended. View detail
Fits: YAMAHA MAJESTYS, YAMAHA Majesty S
It was out of order - - -
I bought the same thing for another Motorcycle, I bought it with confidence because I used it for about a year and there was no problem. However, the one I bought this time suddenly ended suddenly with Rubber to prevent the dropping out of the smartphone - - -
Even if I use it for more than a year, there are products that Rubber can not cut at all, others there are products that will be installed and suddenly disappear.
Rubber, which looks fine, probably probably had scratches.
I do not know if we can exchange or refund it, and if it is possible I decided to give up and substitute 100 Hair rubber as a substitute.
View detail