Reviews
useless
Purchased for Spoke maintenance. Conclusion:It can't be used. First of all, I can't use it with Harley because I can't get over the bumps. It was faster to use Jack. View detail
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
It slips and moves.
Used to attach the Smartphone Holder to the Pipe behind the Screen on the Honda 400X (2019) (with an additional Spacer that comes with the Smartphone Holder).
The size itself is just right, but the hard rubber makes it slippery, and even when the bolt is tightly tightened, it slips and moves. Therefore, I wrapped a thin double-sided tape around the pipe on the body side before installing the bolt, but it is not completely fixed because the outer side of the bolt also slides.
I'm considering replacing the Arm of the Holder with an aluminum spacer only for the type that is tightened with ZETA Bolt.
View detail
Higher height.
I bought this when the Autofocus on my previous iPhone 11Pro Camera broke.
Type VibrationControlDevice to be attached to existing Smartphone Holder3
Just Smartphone Holder3+ IH2100Rigid (25077) The pull-pull mechanism is about 20mm higher than that of the "M" and it shakes more when a smartphone is attached.
I think it can absorb a certain amount of vibration, but the increased height makes it look bad.
If I were to purchase an expensive SMARTMonitoretc. without a phone attached, I would be willing to purchase a used Android phone and use it with TetherRing.
View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA XJR400RII, YAMAHA DIVERSION, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJ400ZE, YAMAHA XJR400, YAMAHA XJ400Z, YAMAHA XJ400ZS, YAMAHA XJ400D, YAMAHA XJ400S, YAMAHA XJ400, YAMAHA SR400, YAMAHA FZR400RR-SP, YAMAHA FZR400RR, YAMAHA FZR400, YAMAHA FZR400R, YAMAHA FZR400
UV sensitive, torn after one year.
The 2LSize is too small for the MT09. Also, it seems to be weak against ultraviolet rays, and the part that was exposed to the sun well deteriorated and tore after not lasting a year. View detail
Commonly usable
I've only used it once, but it works for a change. The air injection type took some time and effort.
In terms of texture, my sleeping posture may not be good, but I had a sore neck the next morning.
Since it is so cheap there, it is not bad from a cosmetic standpoint.
View detail
I want you to write down the Large size of Disc Lock.
The wire lock works normally, but the disc lock could not be used due to its large size.
REBEL250
View detail
Fits: SUZUKI GSX-R1000R, SUZUKI GSX-R1000R
A little difficult to use.
Used on MF17 with FORZABOX. There is no problem with the dimensions, but there is only one place on the back side to squeeze the hem strap, so it is difficult to squeeze the hem as desired. The other manufacturer (company name withheld) that I used to use on other motorcycles was very easy to use because it had both front and rear hem apertures. I bought this one because that manufacturer was expensive, but after about the fifth time I used it, the place where the string comes out was torn because I pulled it too much, so I ended up replacing it. It is too good to throw it away, so I will keep it for two sheets in case of stormy weather. I'm going to give up on it. View detail
Fragile Construction, bad quality plastic.
This item looks very promising in the pictures. I really liked the design. In reality It is very weak. It is made of a very weak type of plastic. I have seen cheap phone holders for 7usd that use better material. There are very important parts in this design that should be made of metal, but in this case those are made of thin plastic. From the outside It looks like the body is made of aluminum, but it is just a decorative sheet metal part. If I knew, I would not pay more than 12 usd for this product. On the other hand, the vibration damper doesn't seem to do much. The Handlebar clamp is made of aluminum, but because it is very thin, It looks like it will break if you tighten the screw too much. Don't use this holder on single cylinder bikes, because the damper is not effective enough. Be very careful when installing this product, because It is not made of strong material and it will break If you tighten the screws too much. It looks like It will not last much under the sun either. For 52usd I expected a sturdy well built phone holder. It doesn't look like it was made in japan because of the cheap quality. It is expensive, bulky and flimsy. Next time I will try with SP Connect. View detail
Not suitable for Side number vehicles.
It is a very effective maintenance tool for vehicles without a center stand. However, if the vehicle is a side number spec. vehicle and has a SIDESaddle Bag, the handlebar will hit the SIDESaddle Bag, so you will need to remove the Saddle Bag. It is better to use a HARLEYPantograph jack such as AstroPROducts for side number cars. View detail
Fits: YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT03
QC CRAP!
About quality and texture I bought this as an alternative to $expensive$ luggage kits. I used it with oxford soft saddle bags. Later on to be used with refashioned, custom saddle bags for a stylish look, which would be harder to fit to proprietary equipment such as GIVI. Hence use of a simpler mechanism such as this one Easy to install, although instructions were in japanese It fundamentally works as intended, but its very heavy, pure steel construction. unfortunately, on this brand new product I found chips in the paint, welding is of low quality upon arrival. Sure its cheaper than other options, but the weld should not be so cruddy that i could have made my own one of same quality for a quarter of the price and my own time. You will see the welding yourself in my photo, judge for yourself. I think this product has a higher weight-limit than it is listed, because the steel rod is very thick and heavy. The unprofessional welding will fail before that bends. I have had mine 3+ months with no failures. shipping was pretty fast from JP to AUS. I don't recommend this product to anyone with spare time and equipment to fasten and tap metal. Just do it yourself as the price is simply not justified. Be careful with shorty style exhaust, as with large saddle bags the bottom of the bag can melt in this setup if is not heat-resistant. I can smell mine burning sometimes on a hot day sitting in traffic, lol. View detail
communicate by wire
It's a great product to use, but
Due to the failure of the wired Disconnection there is
If it's a broken wire near the Speaker
Speaker for Repair is available as a Single Item at a discount.
Wallet-friendly maintenance is possible.
However, the disconnection between Body to Jack
It was overwhelming and troubling.
To prevent wires from getting caught when removing and installing the full face.
Even if you take care of it, the disconnection will continue, even as a User.
I can't think of any more countermeasures.
I tried a wireless Earphone after 3 wires were broken.
When I take off the helmet, it falls off and I can't do anything about it.
After all, there are no other flat Speaker options.
I bought a fourth one.
Rather than adding FMRadio functionality
I wonder if you could take care of the disconnection near the Body exit of the line.
The disconnection near the Speaker is
Speaker inside HelmetPad cover
By putting it in, it's totally gone.
View detail
Fits: KAWASAKI W400, HONDA CB1100, HONDA CB1100 typeI, HONDA CB1100 II, HONDA CB1100 EX, HONDA CB1100 BLACK STYLE, HONDA X11, HONDA X11, HONDA CB1000SF, HONDA CB1000SF-T2, HONDA CBR1000RR, HONDA CBX1000, HONDA CBX1000, HONDA GL1000, HONDA CBR929RR, HONDA VFR800, HONDA VFR, HONDA CB750FA, HONDA CB750FZ, HONDA CB750FB
Price is reasonable. Heat resistant pad comes in a single piece.
Car models used:TRX850 Size:3L
I have been using Y's Gear Motorcycle Covers with Repeat for almost 20 years, but was attracted to the low price and decided to give it a try.
In conclusion, I should have chosen Y's Gear even if it was expensive. The material texture is cheap, but it looks reasonable from a distance because it is black. It is a pity because I would like to put it on the back. The heat resistant pad is only one piece and does not fit my car which has two Exhaust System. I looked at the product specs again, but the quantity of the heat resistant pad is not written. However, 3L is a Large type for Vehicle, so the standard is 2 pads, right? Also, they made me choose 3L because of the fitment guarantee, but it's too big. Too bad.
View detail
Terminal processing is not good.
I bought this for an affordable Automobile Inspection Case.
Difficulty in terminal strength and sewing. Tearing occurred.
View detail
Plastic Parts are too fragile.
Material:Plastic Parts are too fragile.
It is not that the Bolt was tightened with stupid force or that a hard object was slammed against it, but the Plastic snapped off in the order of the claw on the top side that holds the phone in place, the Body side that holds the middle claw in place, and the middle claw, making it unusable within one year of purchase.
The composition of the plastic seems to be hard and brittle, and if the phone is put on and off many times, it seems to get fatigued and go badrill.
I think that if the composition of plastic is changed to something more tenacious, or if it is made of gold, the durability will be improved by a large margin.
I would like to see DAYTONA improve on this.
View detail
Fits: HONDA CBR400R, SUZUKI STREET MAGIC II, SUZUKI WOLF50, SUZUKI STREET MAGIC, SUZUKI RM80LT, SUZUKI RM80, SUZUKI STREET MAGIC 110II, SUZUKI STREET MAGIC 110, SUZUKI swish, SUZUKI WOLF125, SUZUKI GN125E, SUZUKI WOLF200, SUZUKI WOLF250, SUZUKI ST250, SUZUKI NZ250, KAWASAKI Z250FT, KAWASAKI Z250FT, KAWASAKI Z250LTD, KAWASAKI Z250LTD, KAWASAKI ZXR250
Too bad Large change. (This is my personal opinion.)
I bought a new Motorcycle to replace my old one, but the fabric is much thinner than I thought it would be!
My previous Cover in a similar price range was much more solid.
(○Mazon) I also had to apply the heat-resistant sheet of the Exhaust System by myself.
It takes a lot of time and effort. I ended up ordering the Cover I used before again.
Maybe things would be different if they were of a higher grade? It may be different for the higher grade, but the cost performance is not so good.
View detail
Difficulty in moving and fixing the slide part.
I installed it on the handlebar of my Z650, even though the area around the handlebar is narrow and small. It looks nice and simple, but when I installed it on my phone (Xperia5), I had to slide the fixing part, but the slide was not smooth and it was hard to install because it was caught. Also, the lever for fixing is hard and difficult to do. View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
Camera cracks. When the phone is not attached, it is noisy.
[How is it used?
It's a Other Brand ProductHandlebar with separate handle, but I didn't need to use Bracket.
Was the installation difficult?
It is easy to install because it belongs to Hexagon Wrench.
How was your experience with it?
The part that holds the phone is Material:If you don't have your phone on in Plastic, the vibration makes it noisy. I don't want to wear my phone when I'm going for a walk around the neighborhood, but I have to because of this.
When I think that the phone itself absorbs this vibration, it doesn't seem to be so good for the body of the phone, and in fact Camera was broken. (Android)
As a Smartphone Holder, it's affordable, and if you don't make a mistake, your phone won't fall off, but it's not very useful, and the plastic is cheap and makes the Handlebar look tacky.
If you're on a budget, you might want to spend a little more on a good Parenthesis.
[Included Parts:were they on?
It was all there.
Point and hang of installation
If you are using the OEM handlebar on the Ninja 400, you can either run the bracket through the Stem Nut or through the unused screw hole in the clutch lever.
I replaced the handle with SNIPER's Other Brand ProductSeparate handle, which has enough room for the handlebar width, so it can be installed without the bracket.
View detail
If you want to mount it on the Handlebar, it might be possible.
When replacing the DDR-S100 with the Mivue M770D, the DDR-S100 has a MountQuantity option.:I was using Set and wanted to do a similar installation here so I bought it.
Mount of DDR-S100 is Material:I liked the texture in Aluminum, but this is Material:I'm a little disappointed with the look of the plastic. It will probably get whiter with use.
The Nut which is the pair with a special Bolt is probably 6mm though I did not measure it, and I pinched Nut with Long nose pliers and tightened it because there was no Spanner etc. which can correspond in the Tools Set at the time of installation.
I mean, Spanner might be able to fix it, but even if there is a Socket, I think the root of Mirror is in the way and I can't fit the tool to Nut.
Because Clamp itself wraps the Cap of Camera's Rear, it is troublesome that the Cap cannot be removed unless Clamp is loosened every time and the angle is also gap every time Clamp is loosened.
Well, I think that the construction of this clamp and the special bolt together deter theft.
View detail
Looks good after installation.
I bought this together with my MiVue M777D drrorecorder.
Because Rear is set to Fender Eliminator and License Plate Holder is installed, the quantity of License Plate:Pair (for Left and Right) The reason why I bought this product was that it seemed to be incompatible with the Bracket which is tightened together with the Bolt, and I thought that the appearance after Camera installation would be refreshing.
The wrench for the special Bolt is included, but I didn't have a Spanner or Socket in my tool box that fit the Nut on the receiving end, so I used Long nose pliers to pinch the Nut and tighten the Bolt.
I haven't measured it, but I think Nut is probably 6mm.
I thought it is not good to tighten Bolt nut too much because Clamp part is made of resin.
However, Clamp has a softness to fit Camera, so if this is destroyed, I think that the special Bolt is meaningless.
I took a spin around the neighborhood after installation, and the vibration from driving didn't change the mounting angle.
I'll take another look at it next time I go Touring.
View detail