Reviews
Material is not good.
The Material is Plastic and Plating is very poor. If it was at least Steel, I would not have complained. View detail
Satisfied
I installed it on my Z250.
Because the operating noise of OEMRelay was bothering me, I decided to use ICRelay because it was a breakthrough.
It was wider than I expected, so I was worried about hitting Cowl, but it installed without any problems.
To be honest, I think it's an overspecification because OEMValve is rated at less than 50W total, but it's not a problem even if the capacity is LargeParts…
View detail
It's normal and easy to install.
[How is it used?
I bought these to replace the Blinker on my JC92 Grom with LEDs.
It's working fine
Was the one you received as per Image?
Just like the Image, well packaged.
How was your experience with it?
I had no problems at all and it was the right decision to choose DAYTONA!
[Points to note]
Nothing special, but the included Wiring can be installed without using it!
How did it compare to other products?
I was under the impression that cheap products did not have a good reputation, so I chose Mr. DAYTONA, but I think it was good!
View detail
After the Rear, the Front!
I installed it on the Front following the Rear.
At a quick glance, it's hard to tell where the Blinker is attached, but when it's lit up, it has an outstanding presence!
View detail
You can make Blinker disappear!
CRF250L I'm on a MD47.
With the change to EnduroTail, I also changed the Blinker!
I didn't want to give too much away about the Blinker, so I chose this Blinker.
It's so hard to tell exactly where it's attached.
But it's so bright!
View detail
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA CB1300 SF, HONDA CB1300SUPER BOLDOR
As expected of DAYTONA!
Connect with Couplet-on!
It was Exactly OEMCoupler with no rattles!
View detail
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400
a little more
I think it is good if there is a Washer of M5 in the Bolt which is fixing LampBody and the base.
Other than that, I'm satisfied with the quality of the product, which I can't complain about.
View detail
To Restore Old Overseas Cars
It is used for the repair of the old motorcycle in Italy. I decided to use the DAYTONA product which is available at any time because it is large strange to get the same one as the OEM product at that time and the reliability does not seem to be so high. When I bought Relay with Hazard Function in the past, I was able to use it without any problem, so I assume that there is no problem this time as well.
You need to pay attention to the number of poles and so on, but well, Blinker relay is easy to manage if you use the normal one that is commercially available.
View detail
As expected! But a bit expensive & choose Relay!
I sequenced it properly, but even if I use Relay made by DAYTONA, only the first light doesn't disappear a little and blinker...
LED Corresponding Blinker Relay 3PIN (With Hazard function & Position function)
https://www.webike.net/sd/24113652/
I used Relay here.
The quality is fine with the Aluminum body, I was a little concerned about the thin Wiring of the installation.
It was a little difficult to connect to the Bullet Terminal of NORMAL.
I'm not sure how durable it is, but the way it seals and is made, I'm sure it will hold up without a glitch.
View detail
Fits: その他
I didn't use the Position function, but I used it with DAYTONALED Blinker
I don't know much about the Blinker relay itself, I'm just an amateur who knows where the Relay is located.
I just replaced it with the OEM Blinker relay and it basically worked for both Hazard and Blinker.
We use DAYTONABlinker with the sequential function, and the movement of the sequential became Birdie slightly.
(The innermost one ball is sequenced without disappearing)
The other thing is that the Indicator Lamp of the Blinker in the Meter is now very dark.
There were a few unintentional glitches, but the basic operation was fine.
I couldn't understand the Wiring to use the Position function. (I stopped to think.) Therefore, the Large amount of Wiring surplus occurred.
If you don't use the Possession feature, I think you can use other Relays.
View detail
bright
Compared to Halogen, it is very bright. I decided to buy the one that can be worn on the bike after wondering about various products. I installed it on my ZrX1200 DAEG, but it is easier to install if you remove the cowl. View detail
DAYTONA for peace of mind
The size of the bulb is the same as H4Halogen and I could install it without any processing. View detail
Exquisite largeness, yet bright!
[How is it used?
I used these on my main vehicle, an XJR1300C, replacing the OEM Large Blinker.
Was the one you received as per Image?
It was as per Image. The dimensions are listed on the website, so I chose to use a paper cutout of the actual size on the vehicle beforehand.
Recently, Kellermann's Small Type Blinker has been in fashion, but for the XJR1300C, the Small Type Blinker is the perfect fit. It is very safe.
Was the installation difficult?
It's easy to install if you have the level to change the oil.
How was your experience with it?
It is very bright and the visibility is excellent.
[Included Parts:were they on?
Bullet TerminalQuantity:I think it came with a Set, Cut the Harness length to any length and Crimp the Bullet Terminal.
[Was there anything that disappointed you?
Not really!
[ITEMS TO BUY TOGETHER
First of all, I chose DAYTONA Relay for the Blinker relay. The part number is 99989 and it can be installed on the XJR1300C.
https://www.webike.net/sd/24232608/
Next is the BlinkerPlate, without which the Blinker cannot be fixed! I chose the DAYTONA BlinkerPlate as well.
Part number is 97420. around, you need two.
https://www.webike.net/sd/23714066/
And lastly, Posh Blinker Replacement Code Set, you don't need this, but if you don't want to modify OEM Harness or OEM Blinker harness, this is a must have item. You will need two of these for the front and rear. Part number is 092175.
https://www.webike.net/sd/21125587/
View detail
For DAYTONA 675icBlinker relay installation
It's a great product and the delivery was fast. View detail
Fits: Others
Personally
I think it's Small and cool. I asked Shop to install it, but they said that Wiring was too thin. View detail
Fits: Others
more than I thought
It seems to be Wiring thin as well as Front. There is a lot of light quantity. View detail
Blinker replacement
I can make a Blinker that juts out as far as Devilman as Mazinger Z. View detail
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400
Tail lamp replacement
Tail lens like OEM Tupperware pasted on RefreshingSize View detail
Not a good match for the SEROW250.
I installed it on my SEROW250 and it was easy to install, just a little tight on the Waterproof Cap.
It's certainly brighter than the Halogen, but I think the light distribution is not as good with the SEROW SmallerLens.
I switched back to Halogen because the Center is a little darker with Low beam and the oncoming side of the car faces upward, while High beam illuminates the upper part of the car.
The thing itself is Compact and can be pimped, so it's good for Multi-reflector vehicles.
And I bought 4500K, but it's only LED, so it's almost White.
View detail
neither too much nor too little
It's just a hole Cover.
Cut-out of Aluminum with good texture.
In all honesty, the Blinker Hole Cover is just a plastic cover, and I wish it was cheaper, but it is a dedicated product and the fit is outstanding.
It fits tightly into the OEM hole.
There is room to move about 5mm back and forth.
The positioning holes for fixing the OEMBlinker are awkward, so the texture is Minus 2 stars for that.
View detail