Reviews
6Vfor VehicleHorn with few options
YamahaCHAPPY (CHAPPY) I purchased this one because the Horn of
I preferred the look of the long-hole Type instead of the round hole, but I bought this one because it was in stock and I could work on it right away.
It is easy to remove and replace the Horn that was previously attached when it arrived.
The OEM had two bolt fasteners, but since they could not be installed horizontally, they were fixed vertically with a single bolt.
No special Bracket modification or Wiring extension was required.
After installation, I tried playing Horn and it sounded fine.
The voltage is not very stable at 6V and the sound varies depending on the engine speed, so the sound quality cannot be evaluated in any way. (Lol)
"Pi" rather than Bee." It sounds like "I'm not sure.
It's not something I would ever use, but I'm glad I was able to get it to work in case of an emergency.
View detail
Plating is Beauty!
Horn of CUB has not sounded for some time.
I turned the adjustment screw to no avail and looked at the wiring, so I had to replace it with a new one.
We considered OEM, but decided to go with Other Brand Product.
Since it is an electrical system, it is a trusted Manufacturer, DAYTONA.
There were many kinds of DAYTONA products, but we decided on this one, which has Beauty Plating and Classical Design.
It is larger than OEM, so those with a Normal insulator should change the installation location. It may hit other wiring or fuel lines.
The carburetor and the indicator are external to my CUB. I changed the mounting position to the front and bent the included bracket.
Wiring was a little out of reach, so I made my own extension and installed it.
I think it would be more difficult to change the location if the product were smaller in size, but this would be difficult because of the cost of the plating cover.
I have been using it for about 6 months and the sound is Beauty and no problems.
You can see a little from the leg shield but it doesn't bother me because the design is good. It is also good that it has a luxurious feel.
View detail
Sounds good
It has a fairly good Large sound.
As for me, I am satisfied with Large.
View detail
If you don't care about the finish, it might be possible.
It had almost the same dimensions as the SR400 OEM.
The first product I received had paint buildup on the surface, a wound on the edge, peeling paint, and dead insects in the package.
Since we are not in Japan, we probably shouldn't be looking for OEM quality.
I returned and exchanged it because I had Checked it with the Package unopened, but the restocked one also had a buildup of paint in the center.
Well, I used it as it is because it is hidden from the front by Headlight.
Unlike OEM, even the edges are painted, which looks tighter and reduces the risk of rust.
The volume is sufficient. cheaper than OEM. Now I can take on the car inspection without any worries.
View detail
TZr250R (3XV) Used for
[How is it used?
TZr250R (3XV) Just before completing the Restore of Horn, I noticed that Horn was missing and purchased this product that caught my eye.
I chose this product because it is a reliable DAYTONA product and was sold for less than 1,000 yen.
Was the one you received as per Image?
Paint? Electrodeposition? The exterior is very clean.
There were no bends in the Bracket section.
Was the installation difficult?
I guess it depends on the car model, but it was a pontoon on the TZr.
The hose is placed horizontally as shown in the photo, and is co-tightened with the brake hose's detent.
As it was, it slightly interfered with the under bracket of the Stem, so I bent it a little and it looked good.
As for Wiring, it was just the right length without processing from OEM.
How was your experience with it?
The sound is quite high.
I'm sure you'll never get the message. "Peep" I feel it. (Lol)
Well, I may or may not play it once a year, so frankly speaking, I don't care what it sounds like, but it's not cheap.
[Included Parts:were they on?
HornSingle Body, so those who need it should think about what to do with the mounting Bolt and Wiring.
[Was there anything that disappointed you?
None in particular. I felt it was solid for the price.
【Review】
I am satisfied with the quality of the product despite its low price.
The bracket part has two holes from the beginning, so it is easy to install.
I felt it was more cost effective than going out of my way to get an OEM Product or a used one with a broken Horn or a vehicle that was not originally equipped with a Horn.
View detail
It is well made and painted, and has a nice tone.
This product is well made and painted, and has a good tone. It's also inexpensive and easy to dress-up! View detail
It is made in Taiwan.
I bought this because my KSR2 OEMHorn stopped sounding.
You can buy a new one for the same price as OEM used one or less, so I think the cost is very high.
There is Horn made by other companies in the same price range, but I chose DAYTONABrand of safety and trust because it is the one which cannot be disassembled and repaired basically when the inside breaks down like this time.
The Package includes MADE IN TAIWAN and I personally trust them more than products made in China or other Southeast Asia countries.
The material is iron, but the surface is coated with thick plating.
KSR Horn is DC, so I could use it normally.
I think it is seldom, but I haven't confirmed whether it sounds when Horn is AC.
There is a nave screw for the adjustment of the example on the reverse side, but it is not written in the instruction manual. Don't spin it, it'll break. It is stated that
At any rate, there was no problem in the use with the sound quality as it was without touching anything.
It is unconfirmed whether it is possible to adjust it by turning Screw when it stops sounding due to aging or whether it is really damaged if you turn Screw.
In the case of the KSR, remove the 2nd oil tank and work on it.
However, if you remove only one of the two screws from the oil tank, the other screw hole will be overloaded and may break.
By the way, OEM new products of Oil tank have been discontinued.
The OEM bracket has a rubber damper to prevent vibration, but the screw length of HornBody is too short to use it.
If the neck is long, it may become severe in terms of space depending on the type of car, but even the Spring washer of the loosening stopper was difficult to insert, so I thought I would like to set the screw longer by 5-10?
In the meantime, I'm tightening it up.
We have already installed the countermeasure regulator on our KSR, but we were able to install it without any problem.
As for the Nut of Reverse side, there was Space that tightened without a problem with the Twrench of normal Size by removing the Shroud of Right Side.
Because of its location, it is exposed to rain and mud, so I cleaned the terminals well and applied Contact Grease before installing.
The sound quality is larger and thicker than OEM Horn, and it became about a light car.
Horn, which is seldom used but is quite impatient when it doesn't ring at the time of need, can be firmly claimed, and I am satisfied.
View detail
It is a common Universal Horn, and the sound was as I expected.
It was easy to install.
LargeIt was good.
View detail
ZOOMERCustom
It is a pleasant Sound and self-satisfying. View detail
Quality as well as OEM
Motivation
The OEM was functionally OK, but it was Black Painted over rust, so it looked I bought it for the Refresh of
[Why Daytonahorn?
The OEM Product was discontinued and KIJIMA and POSH etc. were considered, and the OEM Product was made in Black (8 cm in diameter) and the same size as the OEM sound by searching for the sound of the Horn of each company We chose this product as a
Installation
If you want to replace the OEM bracket with this product, please use the OEM bracket Installed
The OEM Bracket is in a state of rust as well as the body, so after hanging the paper, it's ready to be used Black Painted and mounted
BracketSize is one size larger than OEMRubber, so OEMRubber I stuffed the packing to prevent it from falling and installed it
[Sound Quality]
Originally, I bought the GPZ1100 OEMHorn as a close sound because it didn't sound bad It is almost the same sound
[Others]
As a Universal Product, it has the same quality as the OEM Product, and it has the same quality as the OEM Product I'm very happy with the low price
View detail
Large size
I installed it in DT230 LANZA I think that Horn that had originally arrived had deteriorated or the volume was sounding too small They didn't notice it, so I decided to replace it at my own peril, but when it arrived It's a little bit larger than OEM, and it was decided to install it after some thought With the Horn, the place to attach the Connector is on top, but with this Horn, it interferes with the So I adjusted the position of the attached bracket and installed it horizontally As a result, it was possible to wear it without interfering anywhere, so it was good, but I installed the Connector sideways The waterproof property is a little doubtful because it has become a little bit I'm a little worried about that because it got bent Well, I think that Large is strong
The volume is a satisfactory Level It's not too loud, but almost like a normal horn But the tone is a little muffled and a little out of tune LOL Some people might be bothered by this
View detail
Necessary and sufficient for an OEM replacement
Purchased as a replacement because the OEMHorn stopped working
In the LITTLE CUB, the grounding wire is required separately, but it's a large Difficult to install because it's not a job
The ease of the game is low
Size is almost the same as the OEM, and the cost performance is also high, so it is a good substitute for Necessary and sufficient
View detail
Okay farm!
What made you decide to buy?
How was your experience with it?
Was it difficult to install? (In the case of hard parts)
If you have the right Bolt, it's easy, easy, easy!
What is the point or hang of installation (for hard parts)?
Consider whether there are any areas of interference at Full Brake
[Do you have any products to compare it to?
Price and reliability compared to KIJIMA and OEM
The sound is light and quite medium
View detail
this is good
Used by FTR 223 asked for a friend to Restore. It was in a condition that the sound of OEM Product rarely sounded, so I exchanged it for Kore. Connector shape also matches, can be mounted Tan. I think sound volume is also normal like Motorcycle. View detail
Horns Posh
Beautiful, fit formy motorcycle kawasaki w800 ,low price But the sound is light. the chrome is pretty and it's more like a motorcycle. View detail
Used for BALIUS
I have never used Horn, but as I pushed it to try it, I did not ring, so I exchanged it for sure.
OEMBracket of BALIUS is strangely constructed, but since it can not be attached to it, every Bracket is exchanged.
Size of Horn is about Small about once. It faces downward like OEM and there is no interference.
I felt the sound surprisingly large, but OEM has never heard of it before I can compare it. Perhaps it is this kind of thing.
It has passed for about a month in Plating version, but it has not rusted yet.
The price is also cheap, it is a good product.
View detail