Reviews
Super loud
I upgraded to 12v and this horn was awesome. it was supper loud and fitted really well, i was super happy with the item and the shipping package ws very safe View detail
DAYTONA PD TypeC
When I use Navigation on my smartphone on a long trip, the battery runs out of charge.
However, with the previous types, it was difficult to charge the battery while using Navigation, but with this type, it is OK.
Charging time is also reduced to Large range.
Satisfied
Note that the plug part will not stick if the plug is too large.
If Cable comes with the phone, no problem.
View detail
Plating is good! Sound is high.
I have been polishing and painting a nearly 50 year old Van Van 75 for the past month or so as a hobby.
When we were finally nearing completion, we realized that the Horn was not sounding. Among several options, we decided on Horn, which has this nice round hole.
Polarity can be either. I also liked the Polished Plating.
View detail
Fits: その他
RelayBody is slightly larger
Purchased to install Hazard switch on DL1000 V-STROM250SX
The wiring is long enough, so when installing the wiring, it was trimmed down to about 500mm and wired at the Bullet Type Terminal.
Wiring for Position is fixed with Bullet Type Terminal near BlinkerWiring.
I'll install the PositionLED Blinker one of these days when it comes out.
However, for the DL1000 V-STROM250SX, there is a Hazard kit (46234) from DAYTONA, and if you are worried about the wiring process, it would be better to choose that one.
I didn't like the supplied On/Off Switch Flat Face Type (40440 ), so I used a separate Slender Switch. [Flat Seesaw Type] (79339), but the price is about 1,,500 yen higher.
View detail
It would be convenient and easy to have it.
The area around the service power supply on the left side of Shinobazen's lower cowl is full of wiring, which may interfere with cowl removal, so we purchased this product in anticipation of future crisis expansion.
The most difficult thing was the location of the D-unit. Shinobu Sen has a space after the battery under the seat, but the bracket plate was in the way and it was not convenient to use.
The installation wiring is fine, and it will be able to handle additional equipment for a while.
What I have noticed is that
Need appropriate tools (Tester/Inspection TesterElectric Works Pliersetc.).
The Bullet Type Terminal is slightly different in size when connecting to a device, so it is necessary to match one of them.
The Power Supply Cable has become stiffer and tougher to handle in Plus.
The lid of the Case is hard to tighten.
View detail
Daytona usb 18w.Good
Type C usb.Bult qulity good.water proof.cable lenth inought for from head cowul to handle bar mount.good thing is out put port dust seal is replacibale.Main power supply cable along with mini barral fuse.Out pout usb c port is very tiny and simple mount with cable tie Unfotunatly my unit dosent work some time in idel rpm,I'm suspecting volatge detecting(even viltage above 12,4v )Any way im satisfied. Charging is good can be charge phone battery quickly. View detail
It's not Kang Tan, right? LOL!
In the product name Kang Tan." but it is not such a kantan to be installed on ELIMINATOR 400.
I don't mean difficult, I mean tedious lol.
To begin with, the problem is on the body side, but the Tank has to be removed in order to install the 4-poleRelay.
This is a pain in the ass, lol.
The product itself is solid, and the Harness fits inside the MeterCowl, so it is a good reflection.
I think it will be around the Handlebar when the retrofit USB Socket is installed, so it will be easy to handle the Wiring! (,,> <,,)
As mentioned earlier, the product received a perfect score except for the 4-poleRelay installation.
View detail
If you are looking for LED Blinker, this is the one.
It comes with a conversion connector so I can just replace the OEM blinker relay and not have a high flasher. View detail
tw200
[How is it used?
Touring
Was the one you received as per Image?
yes
How was your experience with it?
good
[Points to note]
None
How did it compare to other products?
good
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
It is moderately small and good!
It is moderately small and suitable for mounting on NumberSIDE. View detail
![[Highsider] Turn Signal Proton TWO](https://img.webike-cdn.net/catalogue/images/129660/17308_TS.jpg)
Small and wonderful.
Blinker is better for Small. View detail
Magic tape is the worst.
It's battery powered, so there's no back light, but that's not a problem.
When it gets dark, you can't see it at all.
It is attached using the Magic tape method.
The quality of the double-sided tape of the Magic tape was not good enough and I had to put the Magic tape on and off several times.
Body and Magic tape started to peel off.
Glue left on Body and became sticky….
It's a very expensive product for an electric Tachometer.
What's wrong with Included Parts:being worse than it should be?
And even though it's battery-powered, there's no machining of the Magic tape on the battery part.
It's a shame that it's a DAYTONA product.
View detail
As expected
I have just purchased a Z125PRO to take out the power supply for DriveRecorderーetc.
D−UNIT has a track record of use in another motorcycle, and we believe it to be reliable. There are several types of D−UNIT, but since the Z125PRO has almost no space under the seat, we chose the D−UNITPlus, which looked a little smaller, considering its fit.
As expected, we had a hard time installing it, considering the position of the DriveRecorder, etc. Finally, we decided to put it on the frame on the Right Side, but it became quite difficult, so we will review it at a later date. As for the Attachment power supply to operate, I pulled out the terminal near the coupler for failure diagnosis and modified it to interrupt the wiring to get it. The wiring to connect to the battery is weak, and it bent easily when I connected it to the battery and screwed it in. I was able to attach it for the time being, but I am thinking of replacing it with a suitable one at a later date. This is a point that we would like the manufacturer to consider improving.
The power supply has one 7.5A Attachment power supply, two 5A Attachment power supplies, and one constant power supply. 7.5A has a Grip heater, 5A has a USB power supply and DriveRecorder, and the constant power supply has a Cycle alarm. As with the D−UNIT, each power supply has a smaller Bullet Type Terminal than the general ones, so the Female side can be inserted by pushing it in with a little force, but the Male side is loose and will fall out if the Female terminal on the electrical component side is not tightened. We hope that the manufacturer will consider improving this issue as well.
Since the battery is small in a small type car, I think it would be better to avoid moving them all at once, but for the time being, each of them can be moved.
I think it is possible to get power supply without necessarily using D−UNIT, by setting up Relay, or by interrupting Attachment power supply from Fuse, etc., but rather than adding Wiring and Relay to Prank and making a mess, I think that by using this However, we believe that by using this method, Wiring can be reflected and a stable power supply can be obtained, rather than adding Wiring and Relay to Prank and making a mess.
View detail
For LED bulbs
I was using a PMC blinker relay and suddenly the blinker stopped blinking and when I remove it and shake it, it makes a rattling sound….
I purchased the Blinker Bulb to use LED while replacing the Relay.
Incidentally, the Blinker Bulbs are Stanley Electric's CA4887M and CA4587M.
Originally, there were two Relay units attached, but even with only one, both Blinker and Hazard are working without any problems.
It is made by DAYTONA, a reliable company, so I do not think it will break in a short time.
View detail
Used to create Harness
The 25mm Tube Fuse became hard to find and I was using a 30mm Fuse that I purchased at Home center.
After purchasing Stator Coil, Harness, Regulator, etc., the voltage when running was about 13.5V, so I replaced it with a Mini Flat Type Fuse Box from Universal Product and moved it. I wanted to use OEM colored harnesses as much as possible, so I purchased this product.
The running voltage was also improved to about 14.2V, and Accessory CaseSpace was secured.
In the photo I am using Red Wiring, but I found White 2.0Size Wiring elsewhere and will re-pull it.
View detail
Reasonable
I think Kellermann's products are well-known for the polar SmallBlinker,
This one is almost as cheap as that one in performance/texture.
High flasher is not a concern and is recommended.
View detail
Fits: Others
Orthodox USB port
[How is it used?
no problem
Was the one you received as per Image?
Wiring is also discreet and Refreshingly cohesive.
How was your experience with it?
I was able to charge my phone with no problem.
[Points to note]
I doubt that it will be Waterproof on rainy days.
Other items that would be helpful
Installation Point or hang
:Rare/old cars should be installed by a store you can trust.
View detail
Fits: KAWASAKI ELIMINATOR, KAWASAKI ELIMINATOR SE
the same as it was reputed to be
As per other reviewers, it's still difficult to put it up.
The Exclusive Design and Just Size are not tolerant of mistakes, and even if the center part of the main body can be managed, it is very difficult to put the thin and round surrounding parts in the right position.
Seat was thin and stretched when working with it... I was out of my depth.
View detail
Hazard added to XSR125; XSR's Blinker line was a Bullet Terminal from the start
I bought this to add a Hazard switch to my XSR125.
In light of future BlinkerLED, we decided to use DAYTONA's Blinker relay with Hazard function, which is compatible with bulbs & middot; LED.
For XSR125, the interrupt to BlinkerWiring is Large sturdy without processing.
The work procedure is
0.Prepare a DAYTONARelay and Hazard switch (that can be On and Off).
1.Remove the Seat.
2.Remove the Tail cowl.
3.Remove the blinker relay located forward under the Seat and install the DAYTONA Relay.
4.Interrupt BlinkerWiring in a cohesive Wiring behind the bottom of the Seat.
Connect DAYTONARelay's Orange to XSR's Brown line and sky blue to the Green line.
The XSR125 is a Bullet Terminal from the start, so it can be connected without modification.
5.Connect the prepared Hazard switch and DAYTONARelay Red?Black wire with Bullet Terminal processing.
6.Turn on Hazard switch and check operation.
7.Once confirmed, fix the Hazard switch and return Seat Cowl and Seat to their original settings to complete the process.
The work takes about one hour.
Electric Works Pliers or Wiring Connectors are required to connect the hazard switch for Bullet Terminal processing.
View detail
Fits: Others
For charging smartphones
I put it in for powering my smartphone and a separate ETC. Maybe it is because my motorcycle is old, but DAYTONA products always give me a hard time. View detail