Reviews
Fits: Others Universal
Yo...
Installed on the License Plate of Mrs. Rebel250.
I have pushed and pulled this product with it installed before and it went gasketed, but it bent with the License Plate, so I think it has no strength at all.
but purchased and installed again lol
This product is a little larger than the License Plate, and the main points of this product are that it is lightweight and can be easily installed. (´∀`)
Incidentally, when using the included anti-vibration sponge, the gap between the license plate and the panel becomes too large and the panel floats.
Overall, I think it is a good product for dress-up purposes.
View detail
Fits: Others Universal
It was a little too flashy.
I bought this for Number protection and dress-up.
I imagined that the License PlateBody would fit in the body, but it was not quite large enough, so it stuck out. I had to put the attached cushion on it because it floated.
The frame itself is a bit Large, so in the case of Gold, it was an unfortunate point that it would stand out too much.
I think it is an Exactly product for those who like to be flashy.
View detail
Fits: Others Universal
For reinforcing License Plate
Purchased before License Plate was bent.
Silver is refringing, but the overhang of the Plate is one turn (upper and lower Quantities).:Pair (for Left and Right) (about 2mm each) Large size looks like a large.
The anti-vibration sponge is too thick and the plate warps when the bolt is tightened. I shaved it thin and used it. The attached nut is a loosening stop, so I don't think it is necessary to use it.
The supplied Bolt was not long enough and was purchased at Home center.
View detail
The edge is Beauty, but I'm worried about the gap.
I was looking for a moped license frame in silver and came across this one. The frame edge is beautifully made. The screws are a little difficult to fasten when installing the number because the sponge is a little wide. Also, there is a little gap at the corner of the Horizontal Type Number. It is a little bit of a gap at the corner of the Horizontal TypeNumber, but it is not noticeable when seen from a distance. The number screws are probably stainless steel screws, but they are made of a material that looks like a rusty nut. When completed, it has a beautiful, casual custom look. I am glad I chose this License Frame. View detail
![PREMIUM ZONE License Plate HolderQuantity:Set [M6]](https://img.webike-cdn.net/catalogue/images/15903/91946_1_TS.jpg)
Fits: HONDA 400X, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB250R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R, HONDA NC750X, HONDA PCX125, SUZUKI GSX-R125, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX250R, YAMAHA YZF-R25, HONDA CB125R
Stylish License Plate Bolt
The License Plate Bolt was plain, so we installed this product.
The texture is good and will improve the appearance of the car body. You can also choose the color you want.
The installation nut is not included, so the original one must be diverted or a new one must be purchased.
It would be kind if you could include a flange nut with a non-turnover spec.
View detail
![PREMIUM ZONE License Plate HolderQuantity:Set [M6]](https://img.webike-cdn.net/catalogue/images/15651/91954_O01_TS.jpg)
Fits: HONDA 400X, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB250R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R, HONDA NC750X, HONDA PCX125, SUZUKI GSX-R125, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX250R, YAMAHA YZF-R25, HONDA CB125R
things (which) may or may not exist
I bought Plate in Gold to go with it.
I like the variety of colors that are available.
There is nothing wrong with NORMAL Screw, so it is really self sufficient.
View detail
Fits: HONDA 400X, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB250R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R, HONDA NC750X, HONDA PCX125, SUZUKI GSX-R125, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX250R, YAMAHA YZF-R25, HONDA CB125R
A little high
I used it on my Blue metallic TRX850. When I bought it used, I used a Fender Eliminator to adjust the angle of the Number.
I've been wondering about this for a while now, so I replaced the bolt with a connecting bar.
I am satisfied with the way it looks. However, the screws are a little short, so it would be better if they were 3 to 5mm longer.
Durability is unknown
View detail
Note the Size of the License Plate
I bought it in S Size for mopeds, but I didn't know that there are 170mm×100mm wide and 200mm×100mm long even for mopeds.
In Ehime Prefecture, because it was 200mm×100mm in width and 100mm in length in Square Type, this product could not be used because Size did not fit. 200mm×100mm in width and 100mm in length in DAYTONA seemed to be only trapezoidal Type, so Square Small Number Plate Holder Type2 of CFPosh was bought again. Because there seemed to be only trapezoidal Type in DAYTONA, I bought again the Square Small Number Plate Holder Type2 of CFPosh (horizontal 200mm× vertical 100mmSquare Type). The Size and the shape (Square Type, trapezoidal) of the Number seem to be different according to the region especially for the moped.
I think it is the thing as expected if the size is right. The PlateHolder of DAYTONA is working well for another motorcycle (250CC).
View detail
Fits: Others Universal
I am satisfied
I'm a Motorcycle push-around.
I used to bump the license plate a lot.
I bought it for protection.
The Fender Eliminator Kit does not have a Reflector.
Select "with Reflector" MODEL.
The product consists of the Body, Mounting Bolt and a noise suppressor.
Anti-vibration Cushion (Cut already) is included.
View detail
![Premium Zone License Plate Holder Set [M6]](https://img.webike-cdn.net/catalogue/images/15903/91945_1_TS.jpg)
Fits: SUZUKI GSX-S750, HONDA CBR500R, YAMAHA YZF-R3, HONDA CB500X, HONDA CB150R, HONDA CB300R, YAMAHA YZF-R25, YAMAHA XSR900, SUZUKI GSX250R, SUZUKI GSX1300 HAYABUSA, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-R125, KAWASAKI VERSYS-X 250, HONDA PCX125, HONDA NC750X, HONDA CBR650R, HONDA CBR650R, HONDA CBR400R, HONDA CB650R
Anodized is strong.
It's just a nondescript decorative Bolt.
The Bolt is used to sign the License Plate, so it will have no effect on the performance of the MotorcycleBody.
I've been putting it on vehicles that have been stored outdoors for more than a year without Cover, and surprisingly the red color of Anodized doesn't come off.
Anodized in this kind of vivid color will fade pretty quickly, but as expected of Daytona, it's made by Daytona.
View detail
Fits: Others Universal
REBEL250 (2020) It's used in...
This Plate fits fine.
But it's just not a good match for the REBEL250...
The REBEL 250 is equipped with vibration-reducing rubbers in three locations.
This is the part of the Bolt stopper and the lower middle part.
Instead of the rubber in the lower middle supporting the frame, it goes directly to the Number from where the meat is removed.
Also, Number itself may play a role in Fender?
The number of New Model is set on the lower side...I imagine that Small stone hits the place where the meat is removed...maybe.
I failed to choose the right product. I'll install the unpadded one.
I don't think there would be a problem with Full Cowl or something like that.
View detail
It does not need it if it says not to need it (Lol)
It is essential for the current 2 Motorcycle Items?
I made it Black according to Rear Fender, is it a Custom feeling thin?
I should have made a more prominent color, but it is difficult to match with PinkNumber.
View detail
Fits: SUZUKI GSX-S750, HONDA CBR500R, YAMAHA YZF-R3, HONDA CB500X, HONDA CB150R, HONDA CB300R, YAMAHA YZF-R25, YAMAHA XSR900, SUZUKI GSX250R, SUZUKI GSX1300 HAYABUSA, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-R125, KAWASAKI VERSYS-X 250, HONDA PCX125, HONDA NC750X, HONDA CBR650R, HONDA CBR650R, HONDA CBR400R, HONDA CB650R
Good quality
The quality is good. But, there is a point i feel disappointed which is the nuts are not included. I need to buy them separately with extra money. View detail
I was a bit disappointed but were you satisfied?
What made you decide the purchase?】
Because I am in Fender Eliminator, the License Plate has been exposed and there was a fear of bending.
【How was it actually used?】
Rib is solid, there is a sense of rigidity very much, even if you shake by hands Large durable at all.
【Was it difficult to install? (Hard parts case)】
DAYTONA 's Fender Eliminator had difficulty because Nut can not be rotated unless RearCowl is removed because License Plate installation Nut is hidden inside.
【Please tell me the point of installation and hang (in the case of Hard parts)】
I think that it is necessary to check the installation state of the License Plate at the present time and install it according to it.
[Is there anything I was disappointed about?]
Although this is a personal opinion, it is useless because I bought it without confirming the spot, but I think that it was a little thick. Let's say good because rigidity increased accordingly.
【Hope for Manufacturer ? Please let me know if there are any improvement points]
There is a problem with packing. By vibrating during transportation, it seemed like White rubbed like some rubbing and I thought I was going to return it, but I decided it was probably the same and I painted it myself. If it is overseas production, I think that it will be understood by everyone that it takes time to transport, so I'd like to consider the neighborhood.
【Have you compared items?】
YOSHIMURA's Carbon License Plate Holder, but it's too expensive so I decided to do it.
[Others]
View detail
![PREMIUM ZONE License Plate HolderQuantity:Set [M6]](https://img.webike-cdn.net/catalogue/images/15651/91950_O01_TS.jpg)
Fits: HONDA 400X, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB250R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R, HONDA NC750X, HONDA PCX125, SUZUKI GSX-R125, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX250R, YAMAHA YZF-R25, HONDA CB125R
A short leg but a handsome guy
I attached it to Axis Treat.
Bolt is short.
I managed to install it, but I plan to purchase it separately.
The texture is cheap, but I like the shape.
View detail
For Fender Eliminator Kit installation vehicle, confirmation of own vehicle is required before purchase
Based on my experience, I thought that I could easily install. However, our car NMAX 155 was fitted with the Fender Eliminator KIT, and the mounting hole of the License Plate had become considerably higher.
Therefore, it turned out that the Parts interfered with the car body and could not be installed.
Although it is making the product, although slight unevenness was seen in the Anodized processing, it is good because it is the back side. The attached BoltCollar is made like Dress-up. So I decided to use only BoltCollar.
I think the product itself is reasonable for price. It is better to check the location of the License Plate mounting hole of your car before installation.
View detail
![PREMIUM ZONE License Plate HolderQuantity:Set [M6]](https://img.webike-cdn.net/catalogue/images/15903/91948_1_TS.jpg)
Fits: HONDA 400X, HONDA CB1000R, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB250R, HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R, HONDA NC750X, HONDA PCX125, SUZUKI GSX-R125, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX-S750, SUZUKI GSX250R, YAMAHA YZF-R25, HONDA CB125R
I think that it is good for One point
We are using it for mounting Number.
Although it is a product of feeling lost without permission, I think that it is good for a little Accent.
If Bolt is a little longer and I attach a Frame cover a lot, I think it will be different because I can do various things, but with Fender Eliminator Kit attached with Reflector it is regret to install Frame cover with Bolt's Length Limit.
I think that it is more expansive for those products to allow some more room - - -
View detail