Reviews
Fits: KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
A little disappointed.
The design is great, but long touring is a pain in the butt for me personally.
As a result, I purchased DAYTONA's Gay Lupinz.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
Purchased for Loading Hook
I purchased this for the installation of the Loading Hook.
I may replace the Blinker sooner or later, so I need one with Service hole.
It is well made
View detail
Purchased to install a BOX.
Installation is easy if you follow the instruction manual, and the helmet holder is also included. View detail
The variety was small at first.
I bought this product because I really disliked the NORMAL, mossy Fender. The length and width of the Fender was designed to be Refreshing for the two types of Fenders. View detail
Fits: SUZUKI Gixxer SF 250, SUZUKI Gixxer 150., SUZUKI Gixxer 250
Impression after 2 years of use
There are 5 different types of carriers for the Gixxer 150 that are always available, but others are too tough, too weak, too expensive, etc. This one is made of a sturdy material and is good for refilling. The others are too tough, too weak, too expensive, or too many other things, but this one is made sturdily and is good for refreshing.
The material is solid and does not shake even if a 40L~ear box is attached. I am generally satisfied with it.
But this is the point of … I dare to write!
Material is not very good, and even with the cover in place, the rain still soaks in and keeps it wet, so the rust is noticeable, especially in the cherubs that are written under the box. The rust is not noticeable if you don't look into the box because of the location.
The ? front side tip of the Cap is easy to remove. The front side was lost without my knowledge. The remaining Right Side can be easily pulled off by pulling with fingers. The Right Side is probably lost, but I think it got caught and fell off when I pulled it toward me to remove the Saddle Bag. One day, I found a black round disk on the Garage. I don't know. I found out when I was storing it. I pulled out the remaining parts on the Pipe with the broken lid and attached them with glue, but they seemed to come off again, so I used a chair cover instead.
?This is the best It's kinda…" I have a Spacer and a Carrier, but if left unattended in a downpour, water will definitely get inside. I think it is probably opening too much for the Saddlebag Support Plate that can be attached at the same time. I'd better think of a way to block it.
View detail
Fits: HONDA PCX150, HONDA PCX
Windproofing, though.
As far as I have been able to find out, I think this item is the LARGEST as a windshield. (At the time of purchase)
I think the windproof effect is solid in the Large size range.
However, in the summer, when parked in the sun, the light was concentrated on the Screen and the inside of the Screen melted.
It is possible to countermeasure this problem by placing Towel or other material between the two, but be careful, as the entire Towel may burn if it is not properly placed.
View detail
Beautiful product
[How is it used?
Attached to Multi Wing Carrier.
Was the one you received as per Image?
Very nicely cut out Rubber sheet.
Was the installation difficult?
Please peel off the release paper little by little according to the Instruction Manual. I had a hard time peeling it off all at once.
How was your experience with it?
I put a small cold box on the Carrier and it did not scratch the Carrier.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
None in particular
View detail
Alternative to Tank Pad
I put it on my CBR600RR instead of Tank Pad. At a glance, it looks as if nothing is attached.
It is cheaper than the Tank Pad, doesn't spoil the original design of the motorcycle, and has the same functionality.
View detail
Quantity at the time of acquisition of the vehicle inspection:Set
In the case of a used car that has been customized, there may be a case where there is no reflector around the number, so it may be useful when acquiring a vehicle for inspection. I think that this item is always carried by car inspectors.
There are various types of ReflectorSingle Body with Screw Fixing, and with Bracket which is co-tightened with License Plate, but if you have space, we recommend this one which is highly universal and only requires double-sided tape. If you have space, we recommend this type, which is highly universal and inexpensive.
Double-sided tape is also 3M, and DAYTONA is the best for this kind of detail.
View detail
The more you use it, the more you understand! he said.
The more you use it, the more you will know! I had a sore butt after 150km of touring, but the distance was a little longer than the OEMSeat and the pain was a little less (personal opinion). The footing is a little worse when stacked because of the thickness. Also, if you don't attach the strap, the tongue will look obtrusive. View detail
I am very happy with the installation and the effectiveness of Wind Screen!
[Color] I couldn't decide whether to use Smoke or Transparent.
Point of Selection I did not want to change the original image of the Eliminator to a large size by adding the Screen, and I considered the windproof effect of the Screen first and foremost, [Color] I made it a little taller and more transparent than Smoke.
Impressions before and after installation The screen looks very small, and before installation, I had doubts about the windproofing effect, but I experienced a windproofing effect that was larger than expected. Especially when driving at high speeds, the wind that used to hit my body directly became considerably softer, and I feel that stability and fatigue during driving were drastically reduced.
[… So, in a nutshell. I installed it and it was”great” to the best…. This is my current opinion….
Installation work When I purchased the bike, I read the instruction manual on the Internet and initially thought I would install it myself, but as a novice at removing the bikini cowl and headlight, I felt it would be too complicated and I was worried about failure, so I had it installed at a shop. However, I was worried that it would be too difficult for me, a novice, to remove the bikini cowl and headlight, etc., and I was worried that I might fail to do it.
Photo after installation.
Since it is a transparent Screen, I don't think the photo will do it justice, but please take a closer look at it, such as by zooming in Larger. It is not noticeable and you can feel the effect, and I think it looks very nice.
View detail
Fits: HONDA glom
Porting for dio to GROM
I was planning to replace the DAYTONA Screen I had installed on my DIO110 with a new one for my GROM, and I came across a site that had repair parts for the GROM bracket. I placed an order and was able to install it! 。 However, this product DAYTONA91450 and Bolt nut setDAYTONA91451 are required. Also, there is no instruction manual, so please refer to YouTube etc. View detail
Fits: HONDA glom
Replacement of DAYTONA Screen
I was planning to replace the DAYTONA Screen I had installed on my DIO110 with a new one for my GROM, and I came across a site that had repair parts for the GROM bracket. I placed an order and was able to install it! 。 However, this product and DAYTONA91450 Bracket Set are required. Also, there is no instruction manual, so please refer to YouTube etc. View detail
Perfect for XSR125
Mounted on XSR125
Smoked color is a nice touch!
Good wind protection effect.
Even a headwind will not hit your body and make you less tired.
I would recommend it to anyone who is beginning to think the wind is a bit harsh.
View detail
Fits: YAMAHA XSR125, YAMAHA XSR155
It is easy to install. highly effective
It is easy to install with a single hexagonal Wrench.
It can be firmly fixed with a turnstile.
Also works great with Blast Barrier on.
Even strong headwinds became easier.
The work takes about 30 minutes
Instruction Manual can be downloaded at ManufacturerSite, so you may want to study it beforehand.
View detail
The 6-point clamping is strong enough. But there are a lot of places to remove when installing.
Satisfaction with installation is ◎
The 6-point fastening with 4 seat rails and 2 tandem step holders seems to be strong enough.
The instruction manual says Top case is limited to 32L, but we installed 47L at our own risk.
Installation is a bit troublesome.
Seat Cowl, Rear Fender, Tandem Footpeg, Blinkeretc. wiring needs to be removed.
The instruction manual can be downloaded from the ManufacturerSite, so you might want to take a look at it before you consider it.
View detail
For Automobile Inspection Case
I had to tuck it under the Seat because there was no place to store the vehicle inspection certificate.
However, the tag portion of the electronic vehicle verification had become folded in and was about to become unusable as it was, so I installed it as a countermeasure.
The size is a bit large for a car that is not an applicable model, but it is easy to install. However, the attached tape is weak, so be careful when removing it many times, as it may come off including the tape.
View detail
Fits: KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650
Nice chrome parts
It had a shorter tail than the original and a Lukatsu tail brake light, so it had a sense of unity, and it was nice to have all the additional parts to attach a license plate. View detail
SM LINEFender MD44 installed
As per the impressions of our predecessors, the MD38/44 can be installed without any body modification.
Reasonable price and VisualUp, no complaints!
However, in my case, I have prepared the following additional components
Spacer:6.2mm ID x 15mm OD x 6mm L (qty:4)
Bolt:M6 x 30 (qty:2)
Flat Washer:M6 x 22 (qty:4)
When MD38/44 is installed, the spacer thickness should be at least 6mm to avoid interference with the car body. The outer shape may be a little larger than 15mm.
It is fastened with 4 OEMBolt, but for some reason, Quantity:I also bought Bolt because each 2pc is a different length (my used one) and when I put Space on, the shorter one doesn't reach.
When tightening from the tire side, the bolt groove on the FenderBody is large, so the washer is also large. 22mm larger than the bolt groove will cause the washer to ride up.
For your information.
View detail
Installed on SEROW250.
It was possible to install if only the protruding part connecting the OEM Fender and Headlight could be avoided (I used a nipper to cut it off). (^_^;) (e.g. "I'll be back")
FenderRear also manages not to contact the vehicle body
Compared to the OEM, it is shorter and less susceptible to wind, and I feel that it has reduced dizzying when running.
Design was also MATCH with the car body and got tired of OEMSpec.
This is a Recommendation for those who have come to the site.
View detail