Reviews
Prevent the Body Cover from melting in the heat & standing up!
If you don't have this, you can't put on the Body Cover until you get home from touring for more than an hour!
A must have! The design is cool without being obnoxious.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Fallen cannibals
[How is it used?
It's been 9 months since I bought my FZS600, and although I haven't had any standing fender benders yet, I'm taking precautions to prepare for that eventuality. After all, it is a 19-year-old motorcycle, and Silencer is no longer manufactured and out of stock.
Was the one you received as per Image?
I thought it would be a bit larger than I expected, but when I tried it on Silencer, it seemed to be a reasonable large size. It is supposed to be used as a heat guard, but I think it is a little too large for that.
Was the installation difficult?
Attaching it to Silencer is technically less difficult, but the Stainless Steel Band is too long, so it would be Large strange if you don't have the right tool to cut it. I had a wire cutter (a large nipper), so I could easily cut the band with it. Incidentally, the Silencer of FZS600 has a diameter of 120mm, but the Stainless Steel Band is still 5mm long. I had about 0mm left over.
How was your experience with it?
I decided on the mounting position based on where it would be damaged in the event of moss, but I'm not sure if it will work as expected.
[Included Parts:were they on?
A complete set of parts necessary for installation is included as shown in the product photo.
[Was there anything that disappointed you?
I won't know if it works as well as I hope until I actually mock it up, but I hope it doesn't! (Lol)
Other items that would be helpful
Installation point or hang:Tightening the screws of the Stainless Steel Band should be done last; temporarily fasten the Stainless Steel Band and Guard Mount to the Silencer, and then screw the Heat Guard to the Mount. After fixing and positioning the Heat Guard, tighten the screws of the Stainless Steel Band last. If the mounting position of the Stainless Steel Band and Mount is determined first, it will be difficult to position the Heat Guard horizontally.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Heat Guard (because it's a small exhaust system) which can kill two birds with one stone
I installed it on the YoshimuraExhaust System Up Type which was changed by MONKEY125.
I've replaced the Exhaust System.
When stopping:lower your foot and your inner thigh hits Silencer.
When driving:When you kneel, your knee grip hits the exhaust pipe.
So I was having trouble using it on a daily basis.
YOSHIMURA's Exhaust Pipe Guard cannot guard Silencer part.
However, adding the Guard to Silencer is not a good idea because of its cost and appearance.
While I was looking at the Heat Guard of each company, I was wondering what to do.
You can slip it on.
I realized that this was the case.
As you can see in the resultant photos, it protects my feet when I stop and drive.
It's sturdy and sturdy because it's supported at two points by a wide band and doesn't freak out when you tighten your knee grip with your shins.
Moreover, I think that it is functionally superior to other products because the protective Seat to Silencer side is attached as shown in the product photograph.
Just one point.
The Silencer portion is approximately φ90-95 [mm] And since it is thin, the included Band was too much for the Large amount to fit.
I couldn't cut the Stainless Steel Band to protect the end faces with my handheld tools, so I had to use
Separateφ100 [mm] I bought a Band of (extra 3 [cm] (The degree is to the inside of Heat Guard).
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
We protect Side bag from Exhaust System
Saddlebag of Enduris Tan purchased for Silencer because it has partially melted.
Originally, Silencer heat guard was attached, but the length was only 12 cm, and in the forest road Saddlebag gradually moved and hit the Silencer. Although I have not yet gone to the forest road after attaching this Guard, it is probably Large enough to cover the entire Silencer, so I think probably Large is durable.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
DAYTONA Silencer Heat Guard
This DAYTONA Silencer Heat Guard is the product that I looking for. Because it can use as Heat Guard and also use to protect exhaust when motorcycle sliders on the side of the bike. My exhaust is Yoshimura R-77. Although this exhaust not circular but it can fit well. View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
VTR 250 OEM Exhaust System to prevent burning
As the hem of the ride IngPants has melted by the heat of the Exhaust System, purchase as a measure.
As ordinary as shown in the photo, but it is not Visual White in the face so I stroked the Carbon Seat like a photo on the table. As the backing as shown in the picture? Put on the AluminumSeal for the kitchen for the purpose of preventing adhesion and peeling of the dirt at the Slit part. The state of the photograph? Which confirmed the positional relation and made this book. I am satisfied because the appearance is getting better and the function is also good.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON Universal
Reduced waste heat
Slip-on Silencer of WR'S arrived from the beginning to GSR 250 I bought. It is lighter than OEMExhaust System and I like it coolly, but when the inside of the Right foot touches the Exhaust pipe part, Over Pants often melted (Photo Quantity : 1 Set of 4pcs. eye). As a result, Over Pants was melted in the Exhaust pipe section, and the appearance also became worse.
This item has protrusions on the inside (Photo 1st piece) , Because there is a space to be formed with Exhaust pipe, waste heat has drastically decreased compared to before. It is Level which you can touch with bare hands.
In my case, the installation site interferes with Spring because it is the connecting part of Exhaust pipe and Silencer. So it took a while to install LOL
Installation was Large strange but effect - I am satisfied with both appearance and Large. I could hide the traces made in the Exhaust pipe, and it is not hot anything! It is no longer melting Pants.
View detail
DAYTONA:Exhaust Guard Wire Type
Exchange MONKEY Silencer for DAYTONAUp Exhaust System, purchase this product because there is no Heat Guard of Exhaust pipe.
Adaptive Pipe diameter is too large, so 1 inside fixed base. Mounting with 5? Thick Aluminum plate in between. Aluminum spacer making was the most loud strange.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON Universal
Burn It is escaping from hell! Because it has Punch, it looks nice too
Today's wearing! Slash cut wrapped heat-resistant Vantage, but it looks bad Quantity : 2pc. Set attached to each. He insulated it firmly. Use in conjunction with Vantage is effective. I think that it is hot without touching Vantage. It is made with DAYTONA and it is safe and because it is Stainless Steel, I do not mind rust and I think it is a good product.
I also decided to look neatly. The price is also convincing.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON Universal
I got a chimera!
I regularly consciously ride the heel on the tip of the Pedal, but since heels really hit the Exhaust System at the time of Breaking, I searched Guard and made it for DAYTONA made this.
Because it is Punching it probably that heat dissipation is good ....
Because the Band was a bit long, we measured the dimensions and cut it carefully.
Even if the heel hit the Exhaust System it is Large durable!
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
It has good appearance and heat resistance.
I bought it for the purpose of hiding and decorating Exhaust System and preventing melting of Bike Cover.
Installation was a little troublesome work of passing Bolt through Nut and winding a band on protective Seat.
Although it is heat resistant, I tried Bike Cover immediately after running a long distance, but Cover did not melt.
Although it does not guarantee reliable heat resistance, I thought that the reliability is high unless it is an Exhaust System with a little calorific value.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON Universal
Exhaust Guard
Purchase to release from the burning hell of Rear bank Exhaust System of V-type 2 cylinder Engine.
At first, we have wrapped heat-resistant Vantage on Rear bank Exhaust System, but because it looks bad as it is, we installed this item from above Vantage.
The result was very good looking and also attached, so it is very satisfying to be released from the heat of the Exhaust System.
In addition, this product Material : Because it is Stainless Steel, there is not worry of rusting. (Plating is cheap, but it rusts with aging)
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Heat Guard
【What made you decide the purchase?】
I bought it to do Silencer heat guard / Silencer guard of the vehicle.
【How was it actually used?】
Off I am wearing it on a car, but I am satisfied with the appearance well.
【Was it difficult to install? (Hard parts case)】
You can install with Driver 1 pc.
[Is there anything I was disappointed about?]
There is no Band selection for the exhaust system of the Large caliber.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I'm happy if the selection of Stainless Steel Band for Large caliber is over.
【Have you compared items?】
There is none.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Exhaust System Together with heat prevention
【What made you decide the purchase?】
I purchased it as I thought that it would be possible to block the heat transfer from the Exhaust System when installing Side Back.
In addition, we purchased it as a prevention of Silencer dent when falling when off Road.
【How was it actually used?】
I used it with Side Back attached, but my vehicle is Large Engine Displacement Volume, so Side Back has become hot again.
However, Side Back never melted, but the contents of Side Back on the Exhaust System side could only contain things that could burn.
【Was it difficult to install? (Hard parts case)】
My vehicle has a heterogeneous shape and the diameter is large, so the installation Band was Limit and the installation was Large strange.
The vehicle is kTM 690.
【Please tell me the point of installation and hang (in the case of Hard parts)】
For installation of irregularly shaped Exhaust System, installation Band (Stainless Steel) If you bend it according to the Exhaust System shape, it is easy to install.
[Is there anything I was disappointed about?]
I thought it was a little Large. I wanted you to make about half of this Guard.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Because there is a License Plate in the middle of the Silencer in the off Motorcycle of Large mortgage, I think that there are vehicles that will rush out of SilencerRear with this Large rinse.
I felt that it would be good if I put items of this Guard half Size out as well.
【Have you compared items?】
There is none.
[Others]
Heat Guard is used, but also reduces Damage to Silencer when falling.
Because it is Aluminum, it is very lightweight.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Besides Heat Guard
【What made you decide the purchase?】 Required item
I bought it with measures against back damage due to heat when I installed Side Back. I purchased it because the area to Guard is also wide and the price is cheap.
【How was it actually used?】 Required item
Band arrived at Silencer of my vehicle at Limit. Although it is in contact with Silencer, it is still as hot as Silencer in the Engine of Large Engine Displacement Volume.
【Was it difficult to install? (Hard parts case)】 Any item
I think that purchasing from Silencer's diameter firmly is Large Off.
My car was truly Limit, it took a lot of time to install it, but somehow I was able to install it.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Any item
Silencer For vehicles whose shape is not a circle, it is easy to install if you fold the mounting bands from the beginning according to the unevenness of the Silencer.
[Is there anything I was disappointed about?] Required item
There is absolutely no.
Besides the use of Heat Guard, scratches were also prevented at the time of falling.
【Hope for Manufacturer - Please let me know if there are any improvement points] Required item
I am happy that I can choose the Length of the attachment Band.
【Have you compared items?】 Required item
I think that there is only this option for this product.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
I firmly Guard the Side Back.
I purchased to protect Side Back from Exhaust System. With a solid construction, Guard the Side Back firmly from the heat of the Exhaust System. It is a product that can be relieved. View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
I went around Limit
KTM 690EDROEMSilencer ○ Because it is a shape close to a rhombus rather than a shape, I was worried that the length of honest Stainless Steel Band is enough, but Limit managed to circumvent it.
As it is truly Limit, it is impossible for one person to install this car.
Furthermore, it is the most difficult to install scratch prevention Band inside the Stainless Steel Band (Stainless Steel Band is short) So I can burn it so I stuck the Stainless Steel Band Double - sided Tape on the back, pasted the Scratch Prevention Band in the Stainless Steel Band before worked.
Since it is very difficult to retighten the Guard Body after wearing the Guard once, it is easier for the person who wore the Bolt after tightening the Bolt after confirming the position of the accessory part after positioning to the Silencer first.
Double-sided Tape of the picture is not an accessory part, so you need to purchase it separately.
Applications are Silencer heat guard - Side Back Although it is burning prevention, I think that it will prevent scratches on Silencer when falling over the mountain even if you are wearing it on a regular basis.
Material is lightweight because it is Aluminum, but the point of contact with Silencer is Small, so there is a possibility that Silencer will pierce when it falls to a flashy.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
Heat Guard
I went for Camping touring so I bought it for Side Back installation.
When Side Back is in contact with the Silencer, Side Back will melt with heat and it will cause the worst fire.
Install this product in Silencer and make sure Side Back does not touch directly.
Also, other than Side Back installation, it seems to protect Silencer from falling.
You can also correspond to Large Yu Silencer other than Size by purchasing separately purchased Gold Genus Band.
View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
It was used for the external Muffler of a MAJESTY125.Texture was good than expected.It is charms that the BALI remained in the rear face.Since it does not get hot at all, it is a Recommendation.
It was used for the external Muffler of a MAJESTY125.Texture was good than expected.It is charms that the BALI remained in the rear face.Since it does not get hot at all, it is a Recommendation. View detail
Fits: HONDA CBR400R (2013-), HONDA 400X, HONDA CB400F (2013-), HONDA CBR400R (2013-), HONDA NM4-01, HONDA CB500F, HONDA CB500X, HONDA CBR500R, HONDA CB500F, HONDA CB500X, HONDA CBR500R
it hits a Muffler, although he would like to attach a Side bag ... and those that are in trouble -- be absorbed! It became touch that a Muffler supported a Bag, like the photograph, and became good exactly. Heat is not transmitted, either but a
it hits a Muffler, although he would like to attach a Side bag ... and those that are in trouble -- be absorbed! It became touch that a Muffler supported a Bag, like the
photograph, and became good exactly.
Heat is not transmitted, either but an inner load is also safe.
He carried out the 30,000-km Touring during two years now, and had no problem.
It may be useless in case of
, however the Type which the Muffler has raised more.
It is for preventing a guide peg's hitting from the first and getting hot well.
View detail