Reviews
The current model was no good.
I installed it on my current LEAD125 and it was not difficult to work on.
I thought the LEAD125 was large and durable, thinking there would be little change from the 2BJ-JF45. I will replace it with an Asahi windshield product as soon as possible.
View detail
Magic tape is the worst.
It's battery powered, so there's no back light, but that's not a problem.
When it gets dark, you can't see it at all.
It is attached using the Magic tape method.
The quality of the double-sided tape of the Magic tape was not good enough and I had to put the Magic tape on and off several times.
Body and Magic tape started to peel off.
Glue left on Body and became sticky….
It's a very expensive product for an electric Tachometer.
What's wrong with Included Parts:being worse than it should be?
And even though it's battery-powered, there's no machining of the Magic tape on the battery part.
It's a shame that it's a DAYTONA product.
View detail
Delicate product!
The Ideas is very nice but too moronic. The Torque wrench is specified for tightening, but would you use a Torque wrench to tighten it if it comes loose on the road? Ideas is good, but please improve it! View detail
Doesn't fit to Kawaski Eliminator USA version
EL450 USA doesn't use the same connector as the JDM version. So you can't use this on your motorcycle. Don't waste your time and money. View detail
![Disc Brake Kit for Inner Fork [for Brembo 2P Caliper Pitch 84mm]](https://img.webike-cdn.net/catalogue/10054/79246_1_l_TS.jpg)
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey, HONDA monkey
No good!
The union of KITACO's 8Inch2.5 and the new Crab interferes with Caliper and Wheel, making them unusable.
The instruction manual is not very helpful.
View detail
Fits: HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
Condensation is ManufacturerSpec.
The review said there was condensation, but there was no mention of it in the product photos or description. However, when I received the product and looked at the package, it said in large letters that condensation occurs. I don't think you can just buy a product without knowing about it and then ask for permission. Also, the temperature is indicated to be up to 200℃, but I thought it would burn out before that. View detail
Fits: HONDA CRF250L, HONDA CRF250L RALLY, HONDA CRF250RALLY S, HONDA CRF250RALLY, HONDA CRF250L RALLY, HONDA CRF250L
Too inaccurate to install
Right SideBracket was too inaccurate to install.
I managed to install the Left Side, but could not use it as a product at all, hence this rating.
View detail
Durability Zero
I installed it in a GSX1100S and used it for a few days, then suddenly it became inoperable. I am extremely disappointed. View detail
Failure after using Grip-Heater
Grip heater
Smartphone Charging
drive recorder
The above three points were connected.
In the summer, it worked fine.
Grip heater was connected at 7.5A.
It was getting cold and when I turned on the Grip heater, I smelled a burning smell and then the other two points stopped energizing as well.
View detail
I can't get it.
Purchased as a temporary substitute.
When I tried to remove it two weeks later, it was stuck inside the handlebar or something, and no matter how hard I pulled it, it did not move at all, and I could not get it off at all (I had loosened the Screw enough to make it spin).
I struggled with it for about an hour but was frustrated. I gave up trying to pull it out by hand and decided to prepare a tool.
And two weeks after I prepared the tool to pull it out (about $2,000), I pulled it lightly before using the tool. "What? Did you get out of there easily?"
Did leaving it for an extended period of time cause the Rubber to revert back to its original state?
It's good that you got out so easily, but it was expensive.
View detail
This product is difficult to install and has a high work risk.
This product is difficult or impossible (for amateurs) to install due to individual differences.
As noted on the product page, it is necessary to adjust the angle of the banjo bolt on the brake, change the routing of the switch harness, etc.
Especially if the footpegPedal is moved even slightly while the banjo bolt is loosened, it may bite the air.
Although there are some aspects that cannot be helped because they are due to individual differences in Motorcycle, basically, these are not tasks that should be performed by amateurs.
(An image of the Instruction Manual is also attached, but if you do not know what the word ”air removal” means, please do not install it by yourself.)
Please note that you will not know if you need to do the above until you actually remove the footpeg, so be careful if you intend to do the work yourself.
In OEM condition, the banjo bolt is coated with Check pen, so you can see it later when you loosen it.
We recommend that you DIY the installation knowing the risk of not being covered by the manufacturer's warranty in the event of a problem with your own work, or have a motorcycle shop perform the installation for you.
I gave up on installing it on my CL250 by myself because it looked too far away to do anything about the angle of the banjo bolt.
I felt evasive because even if it were installed, it would likely be very Hose stretched.
I may ask Motorcycle shop to install it when I get around to it, but I have a feeling that some other company will have a more nifty footpeg available by then.
The material is made of a solid material, so as long as it can be installed, it can be used without problems.
However, I felt that the product design was poor for a product made by Large Hand Manufacturer, although I think one of the reasons is that it is custom parts for a car model that has just been released on the market.
I have experience in total replacement of Brake line, but I optimistically think that amateurs should not work on cars with ABS.
(If there is an error in ABS, it can only be fixed by the Manufacturer.)
I would not recommend it at all unless you are really having trouble with your footing right now.
View detail
Is it a coincidence?
Crack crack about 2 months after replacement.
It was so unreliable that I ordered an OEM Product to replace it.
It is not mentioned in your Impression and it happened to be a HaGap.
View detail
Fits: HONDA hornet, HONDA Hornet 600S, HONDA Hornet 600, HONDA X-4 Type LD, HONDA X-4, HONDA VTR1000F Firestorm, HONDA VFR750R, HONDA VFR400R, HONDA BROS 400, HONDA BROS650, HONDA CB1000SF-T2, HONDA CB1000SF, HONDA CB400SF, HONDA CB400SF version S, HONDA CB900 Hornet, HONDA CBR900RR Fireblade, HONDA NR750, HONDA NSR250R-SE, HONDA NSR250R-SP, HONDA NSR250R
Doesn't work. Price is right.
I knew it existed, but this is the first time I have used it.
I had some expectations because of all the rave reviews, but I am very dissatisfied.
Are you mistakenly thinking that if you don't grip it, it doesn't work, but it only works as long as you grip it?
I think Situation is Touring because it is only cheap, but it will not be an option again.
View detail
Fits: Others Universal
It may not be attached depending on the individual Number.
[How is it used?
I purchased this product as a vibration countermeasure for a single cylinder.
Was the one you received as per Image?
Yes
Was the installation difficult?
Fixed with Bolt, so it's easy
How was your experience with it?
I was disappointed that it didn't fit tightly in the Frame, perhaps due to individual differences in the Number.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
Not sure if the 250cc Number will stick securely (L Size)
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja1000, KAWASAKI Ninja250, KAWASAKI Ninja400, KAWASAKI Z1000, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI 1400GTR, KAWASAKI GPZ900R, KAWASAKI Ninja ZX-14R, KAWASAKI Ninja ZX-14R, KAWASAKI Ninja250R, KAWASAKI NINJA400R, KAWASAKI Z1000, KAWASAKI Z1000 R EDITION, KAWASAKI Z250, KAWASAKI Z750, KAWASAKI Z750 S
Does not fit ZX-14R
Screw is about 10mm too long and hits in the back.
DAYTONA's answer is because it hits the Screw Lock agent and doesn't go in.
In fact, it does not go in due to physical interference.
If this is all you need, you can buy a screw 10mm shorter.
There is no way that consumers will pay Gold for Screw as a product.
Also, the weight and the handlebar end face interfere with each other, and our STD Handlebar's
Only the Left Side did not go in the back.
DAYTONA's answer is to prevent interference due to protruding welding etc.
It is designed to have enough room for Clearance.
It did not actually stick.
View detail
![[NATIONAL CYCLE:National Cycle]Vstream Windshield](https://img.webike-cdn.net/catalogue/images/75533/16971_TS.jpg)
Fits: HONDA PCX150, HONDA PCX
Parts that give Damage to the vehicle body
The resin inside the Screen had melted when it was parked outside during the summer days.
I think the light has been focused like a magnifying glass just at the point where the Screen's Curve becomes tight.
It is a design flaw.
View detail
Fits: YAMAHA SR400 19, YAMAHA SR400 19, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400
Would be nice if the instructions were more helpful.
The CABTON Exhaust System was installed at the same time as the CABTON Exhaust System replacement.
When he stepped on the bump while turning, the STAND touched the ground and he had a near-miss.
Without this, the STAND would contact the Frame, but
I have removed it now because I thought it would be better than scrubbing the ground.
View detail
fall (e.g. in status)
Slip. I thought it was an initial slip, but it slides.
And a familiar Motorcycle shop. I'm going to ski DAYTONA. I would recommend OEM because OEMMEMBelt is expensive but you don't have to buy cheap.
View detail
China Quality
Just as the warranty was about to expire, it stopped working altogether.
I asked Manufacturer to repair it (for a fee), but they refused.
No repairs. They want me to buy a new one.
I see that it breaks easily in other Reviews.
I feel that many of this Manufacturer's products are terrible in my experience.
View detail
Everything is China Quality
It broke just as the warranty period was expiring.
When I asked Manufacturer to repair it (for a fee), they refused.
They did not repair it. They want me to buy a new one.
I see many reports of breakage in Reviews of this item (Single Item).
I think many of this Manufacturer's products are terrible.
View detail