Reviews
It is a modest Parts.
I'm on a Sidecar made in Russia, Ural GEARUp 2015 MODEL.
One day, I noticed that the stop-lamp did not turn on when I stepped on the rear brake.
The Spring that was supposed to be attached to Brake's Switch has gone missing.
When I contacted the authorized dealer where I purchased it, they said that SpringSingle Body does not provide parts.
That's why I bought this one. I really only need 1 pc.
View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPz400F/F2, KAWASAKI GPZ400R, KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI D-TRACKER, KAWASAKI ZRX1200, KAWASAKI 250TR, KAWASAKI ZRX1100
Float packing
I chose this one instead of OEM Product, it is cheaper. I don't know how durable it is yet. View detail
Baffle with care
I used it on a KawasakiZ1 with a PAMS assembly tube.
The method of using CB750's Normal muffler's Baffle for the assembly pipe was seen in old YOSHIMURA pipe. The conversion adapter is very accurate, so it can be installed on most of the tubes.
Sound does not get tired when running with the bass sound working. In addition, the appearance of Exhaust End can direct the sense of particularity because the person who installs this Baffle is not seen too much. It is a good Baffle.
View detail
It works on the FCR Carburetor Body Down draft!
Used for maintenance of FCR Carburetor Body.
For support. "FCR Carburetor BodyHorizontal and Down draft does not appear to be supported, but
It is available without any problem. (If you have the Parts List of FCR Carburetor Body, you can judge.)
As for the quality, the accuracy is the same as OEM.
Durability is unknown, but Float chamber packing is a consumable item, so if you change it regularly, you won't have any problems.
For this price, you should change it before it gets damaged in the first place.
Also, I use Konishi's quick-drying BondG103 for fixing.
The glue residue is so strong that it's a pain to remove the old glue, but other than that it's good. For your reference.
View detail
I used it to convert my KLX250ES to BlinkerLED.
I bought the OEM Blinker relay for my KLX250ES because it was 3 pole and it was cosmetically sound.
This Relay is a Material that comes with the OEMRelay.:Rubber Bracket and there is no part to fix it.
It is Large fineness compared with OEM.
I had a 110 Coupler 3-pole and a H4 Coupler left over, so I used Vinyl Tape, Heat Shrink Tube, etc.
Waterproofed Cable is made, connected and secured with Tie Wrap.
The front blinker of KLX250ES is 110 type 2-pole coupler and the rear blinker is Bullet Type Terminal connection.
The Indicator bulb in the Meter's Blinker must also be replaced with an LED or it will become a High flasher.
I am left with a bulb pulled out. ^ ^;
As others have mentioned, it only flashes once when Blinker is turned off.
View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPz400F/F2, KAWASAKI GPZ400R, KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI D-TRACKER, KAWASAKI ZRX1200, KAWASAKI 250TR, KAWASAKI ZRX1100
Float packing
I bought this because I'm overhauling my friend's carburetor and although it's not OEM, I can install it without any problems and there are no leaks. The price is very reasonable. View detail
1/6 the price of KEIHIN!
The Float packing for the FCR Carburetor Body costs around $1,200.
You will be amazed at the price of this Cherry.
I used to have the impression that the Rubber parts for Cherry carburetor were not very strong on Gasoline.
After that, they improved RubberMaterial (so I heard), so I repeated it, hoping for revenge.
Actually, I haven't overhauled it yet, so usability and durability are unknowns.
If things go bad in a short period of time, I'll post again.
View detail
Hidden components of self-sufficiency
I was worried about the tattered Bump rubber, so I put on this product which fits the diameter of the shaft, and since it was troublesome to remove the Spring, I cut into the Bump rubber and installed it through the gap in the Spring. The inner diameter of the spring is a little narrow, so there is a gap in the cutout area, but it's not a problem if you can't see it! The suspension never bottoms out so it doesn't have any effect, but it looks like an OEM product and I'm happy with it. View detail
Is it cheap enough?
I bought it at a good price because the Lever area was getting a bit worn out.
Installation is easy as you just remove and replace it.
The problem is when you take it out of PetitPetit.
From the moment I opened it, there was a Wound in Lever's grip, and when I looked at the back, there was a spot where the base of the genus Gold was showing.
The paint is sparse and the visible area around the Mirror installation is crumbly and muddy.
Even though it is made overseas, TensionDown from the moment I saw it.
Is it called Short Type? Is it? The grip is shallower than the OEM Product I have been using.
I turned the adjustment screw a lot and finally completed the adjustment.
It's fine for use, but it's worth the price.
View detail
Fits: HONDA CB400FOUR (water-cooled), YAMAHA XJR400R, HONDA CB400SF, KAWASAKI ELIMINATOR 250, KAWASAKI GPz400F/F2, KAWASAKI Z400FX/Z400J, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZR-7/S, SUZUKI BANDIT250, SUZUKI BANDIT400, SUZUKI GSX250S KATANA, SUZUKI GSX400S KATANA, SUZUKI GSX400, SUZUKI GSX400, YAMAHA XJR400R, YAMAHA XJR400, HONDA CBX400F, HONDA CBR400F, HONDA CBR250R
Gasket
There is no exhaust leak and it works normally. View detail
Float packing
I bought this as a spare because I bought the FCR Carburetor Body33 and had to open and close it many times for setting. I haven't used it yet, but the texture is Large and it looks strong. I will buy it again next time because it is cheap. View detail
CHERRY Cherry Φ70Short Tube Hand BentType
It's well made for the price. ！！！！ View detail
A little bit easier on the high speed
I used to have a moped windshield (the kind often found on CUBs) on my XR250 for winter wind protection.
It's been a few years since I removed the Mirror as it was co-tightened and the wind was blowing in from underneath and the Visor from the Off-Road Helmet was hitting it.
Lately I've been thinking about whether it's better to put a Small-looking Visor on CRFrally or some other Image, or leave it NORMAL.
I'm going home at night in the countryside, which is a situation where I'll be attacked by insects, so I decided to wear it for the coming season.
Installation is purchased on the premise of processing because it is called Universal. Adjust the angle and height with additional Universal Bracket.
The top of the shield is a little warped, so I wonder if that affects the effect.
It is fixed with two points so that it can be moved when it is dangerous, but it is packed with towels because it is a little chattering.
I love it because it looks unrecognizable at first glance, so it's casual.
View detail
Fits: YAMAHA SR400, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA DRAGSTAR1100
For first aid, it is Recommendation.
It was used in the Under-seat engine hall.
I think it's cheap and good, but again, durability is nowhere near as good as it should be.
I think it's enough if you use it overhauled for a long period of time, for example, if you suddenly have a gasoline leak and have to do emergency treatment.
A good product if you use it differently.
good point
The Gold amount per unit is low, so you can always have it for stock.
If you want to use it as a first aid, it is highly recommended.
It's also oil-resistant, so it passes the test.
It can also be used for XJR and other vehicles.
A bad point
The durability is still low. I don't think it will last half a year.
The Size does not match delicately, so it bites with Body.
Recently, I've come to think that it's not that cheap parts are bad, but that you should use them differently.
There is also Merit that it is suitable for always having in the Trouble which is attacked suddenly in the travel place, and this product is always stocked in Back and goes out.
If you're looking for a serious Overhaul, I think OEM is the best way to go.
View detail
Fits: KAWASAKI CR Carburetor Large body|Small body
I bought 8 cards and I'm out of 5 ______.
It is an inferior product. At least Quantity:1 Set of 4pcs. is a good product I wanted … View detail
Chromium Plating is still good
I was told by a motorcycle shop that I shouldn't use Stainless Steel because it's too hard and will break, so I decided to use Uniqlo plating or Chromium Plating. When it investigates further, it discovers the one made of Cherry. Because it is cheap though it was the Manufacturer which is not familiar very much, it buys for trial. The quality was firm, and I was able to assemble it without stress when I installed it. I like it very much because the foot area becomes like a new car.
The Uniqlo plating and the Chromium Plating will divide your taste, but I prefer the mirror-like Chromium Plating to the blueish Uniqlo plating.
View detail
Change the Spoke for a dress-up
I was told by a motorcycle shop that I shouldn't use Stainless Steel because it's too hard and will break, so I decided to use Uniqlo plating or Chromium Plating. When it investigates further, it discovers the one made of Cherry. Because it is cheap though it was the Manufacturer which is not familiar very much, it buys for trial. The quality was firm, and I was able to assemble it without stress when I installed it. I like it very much because the foot area becomes like a new car.
However, as you can see in the picture, if you look closely, you can see a small piece at the base of the Spoke. "S" It has a Mark on it. I don't mind it, but you may have different tastes.
View detail
FZ1FAZER08
Replace the Handlebar Post of FZ1FAZER08 with the one for de Raster250
If you install this product, you can get to the Limit where you can't hit the Tank.
Position can be lowered
View detail
Float packing
Float packing for FCR Carburetor Body33, but I think it is cheap and good. I will buy it again next time. View detail
Needle clip
Needle clip is indispensable because you can't fix the height of needle without it. it is better to put a clip on each needle instead of removing it when you change the needle. View detail