Reviews
Maybe better than OEM….
Compatible Float Chamber Packing for FCR Carburetor Body.
The FCR Carburetor Body was originally designed for down draft, and the oil level is above the packing, partly because a horizontal float chamber was added later.
Because of this, after three years from new, the lamination will start to bleed a little bit from the joints.
My FCR Carburetor Body had become a 10 year old player and the seepage was getting worse, developing into a leak rather than seepage, so I replaced it.
It has been over a year since the replacement and there is no seepage at all.
I have no problems with the installation and even think it is rather better than the OEM when looking at the lack of blotchiness.
Well, I could have arranged a reliable OEM Product, but it would have been a hassle to go to a mass retailer and place an order with a young clerk every time. Was the FCR Carburetor Body 250cc? " "! No, it's a carburetor…" I didn't really want to go there because of the exchange that took place.
This product is considerably cheaper than the OEM, and the performance seems unmistakable, and I think FCR Carburetor BodyUser would be well advised to buy it while shopping at webike.
View detail
For FCR carburetors, can be used for a long time. View detail
Reasonable price
It is a component that is easily ruined.
It would be great to get this price.
View detail
FCR
They are cheaper than OEM and seem to work fine. View detail
Clip easy to lose, cheaper than OEM!
Clip of FCR Carburetor Bodycarburetor that is often easily lost.
The price is fairly good, but this product is cheaper than OEM and can be used without any problems.
For inventory replenishment, spares, etc.
View detail
Fits: HONDA CB650, HONDA CB750F, HONDA CB900, HONDA CB1100F
quality
It is a product, not a product, and I am surprised that Webike would sell such an inferior product as a product,
The product does not have the minimum quality required for the product (skinny, stretches after one use,)
The result is the same no matter who does it, since it is tightened by default Torque,
Are you sure you don't want to apply liquid Gas and install it? (There is no such instruction in the manual.)
After replacing 4 pieces, one leaked immediately, and the rest will leak soon after they heat up.
View detail
For when you lose it and can't do anything about it, or...
FCR Carburetor Body39Φ, used for KEIHINOEMJet needle.
OEM Clip does not get stuck in Pushing and spinning.
But this one is round and round and rattles up and down.
Description. Universal Product, but without vertical wobble. What if there's a "what if"?
Maybe it's not the Level I'm concerned about,
I am not inclined to use it as long as the OEM fits so tightly.
You should buy KEIHINOEM.
I bought it just in time to adjust shipping charges when purchasing OEM Parts,
Well, the shipping cost was zero at 360 yen for 6 pieces, so let's call that a good thing.
View detail
Commonly usable
After running the FCR Carburetor Body on a vehicle that had been in long-term storage, it was still leaking fuel.
If it is OEM, you can't go wrong, but for Gasket, I wanted to try something at a good price.
It is normal. I bought two just in case.
If it leaks, it is Large sturdy and will not leak out once assembled. The most common problem with other brand products is that they absorb gasoline and expand and stretch, making it impossible to put them on.
Can I use it without any discomfort at all?
View detail
Fits: YAMAHA XJ400, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJ550, YAMAHA XJ400, YAMAHA XJR400
Packing too thin
Two of the four sheets ripped easily when I took them out of the bag. I used the 2 that were usable, but no leaks. 。 If you open the Float chamber for the second time, you might burn it? View detail
cheap
It is much easier than the OEM ones.
There were no leaks, so I don't know about durability, but considering it is disposable, I think it is a very good value.
View detail
It is cosy depending on how it is used.
Used in O/H of FCR Carburetor Body.
However, if the Float is soaked in Gasoline, it will expand slightly, so you will need to dry it out and wait for it to return to its original state, or make other adjustments when reinstalling it.
View detail
Fits: HONDA CB650, HONDA CB750F, HONDA CB900, HONDA CB1100F
More than OEMs …
Used for carburetor OH in RC04.
The OEM Product did not sit well in the grooves of the Float Chamber and in some cases required dotting with superglue, but this product was just the right size.
The material used may be fluororubber, which gives the impression of being solid, unlike the NBRs that are often used in inexpensive other brand products. Of course, the Leak test was no problem.
In OEM Quantity:Although it must be expensive because of the set sales, I am grateful that it is available at a low price.
View detail
Fits: YAMAHA XJ400, YAMAHA XJR400R, YAMAHA XJR400R, YAMAHA XJ550, YAMAHA XJ400, YAMAHA XJR400
CherryCarburetor Float Packing
OEMs are too expensive to buy, so if you're not sure...
Cherry has found a Float packing that she has been putting out!
It's a Commendation because it's reasonably priced!
So far, no leaks, etc.!
View detail
Fits: KAWASAKI For vehicles equipped with TMRSingle|Multi each Small body|Large body(Φ28-Φ41)
distortion
I used two of them, including a spare, because they were cheap, but they were distorted and difficult to use.
After all, we use OEMs.
View detail
FCR Carburetor BodyFloat packing
I bought it because I wondered if it was oil resistant.
The item itself did not lose its shape and fit as usual, so for this gold price, I think it is excellent in terms of cost performance.
We'll see how durable it is.
View detail
FCR Carburetor Body Float packing
I was looking for packing for the Float chamber of the FCR Carburetor Body and found this item. The first thing that caught my eye was the gold price and the words "Durability UP". I found it to be a normal packing, and it fits in a normal way. The only thing left is the question of durability. View detail
Fits: KAWASAKI BALIUS2, KAWASAKI BALIUS, KAWASAKI XANTHUS, KAWASAKI ZXR250R, KAWASAKI ZXR400R, KAWASAKI ZXR250, KAWASAKI ZXR400, KAWASAKI ZXR750, KAWASAKI ZZR400
Soak in Gasoline for a little while to stretch it a bit and get it just right.
As others have said, at first the Rubber is too short and not very attached.
If you force it on as it is, it will bite and overflow all over the place.
It is recommended to soak the packings in Gasoline for a little while before use so that the packings will stretch nicely.
p.s. If you soak it too long, it will grow too long and you will not be able to get into it, so if it grows too long, let it dry for a while.
View detail
I was able to use it for Down draft.
I was worried because it's much cheaper than OEM, but I haven't had any problems and no Gasoline leaks.
I installed it on the FCR Carburetor Body of Down Draft Type.
If you open the Float many times, it may not last, but if you open it only a few times for a short period of time, I think it is Large durable.
So I think it is good for disposable during Carburetor setting.
View detail
คุณภาพสมราคาที่จ่ายไป..ชอบมากครับ View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI GPz400F/F2, KAWASAKI GPZ400R, KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI D-TRACKER, KAWASAKI ZRX1200, KAWASAKI 250TR, KAWASAKI ZRX1100
Float packing
I chose this one instead of OEM Product, it is cheaper. I don't know how durable it is yet. View detail