Reviews
How effective would it be?
I bought it with the static eliminating Bolt and some kind of product that is hard to tell if it is effective or not, because I got quite a bit of it when Point purchased the Full Exhaust System. To tell the truth, I was reluctant to purchase the product at actual cost.
Used for empty Bolt hole in FinalDrive gearCase of R1250RT.
Since Oil is also used inside the Gearcase, we tried attaching it to the Gearcase for its static eliminating effect, but the extent of the effect is unknown.
View detail
To the horror of static elimination!
This is an addendum to the in-play
I felt a decrease in torque at high speeds, so I changed the MJ immediately
As a result, it's back to the way it looked before the product was installed
But how things have changed, as far as the high speed range is concerned
Raising the MJ did not change it, it simply went back to the way it was
Where did the gas for the MJ raise go?
I'm sure it's being de-energized in a place I can't feel (Laughs)
Also, the stakes have changed with the MJ exchange
When you open the Axel from a standstill, does it feel like you're going to come forward much more forcefully?
That feeling will continue until you get on Speed to some extent
More carburetorQuantity:If you boil the Set down, you'll be able to experience the changes in all areas, but the maze
I'm going to stop because I feel like I'm getting lost
I'm happy with the changes I've experienced in my current state, at least a little bit
But still, I'm afraid of the power of static elimination
View detail
carburetorQuantity:Set has changed
I installed PWK28 on my LEAD 100 and this time I installed this product
LEAD is a long Manifold anyway
NORMAL, of course, because of the longevity of the mani that I one-off to my for PWK28
i installed 2 places in total on the carburetor side and the Lead Valve side
When it comes to the test drive, low speed, medium speed, it doesn't feel any different than before
The biggest change I felt was in the high speed range, the torque seemed to be thinner... (-_-;)
Looking at the plug, it looks like White
The air that was being pulled by the mani due to static electricity is gone, and the amount of air entering the Engine has increased Isn't it?
Now, let's see if we can't make an MJ exchange
I hope it turns out to be a good one!
View detail
It was already de-energized …
When I checked NGCJapan's homepage, I found out that Front I bought it because it was listed as a good one in the forkBottom Shaft's Fixed Bolt
Installed to RZ-R's Fork bolt and test ride
Apparently it was already de-energized and I couldn't feel the effect
Actually …
Nut to Rear Chain Adjustment Nut to Others also static eliminator Nut
Indicator Volt also has a static eliminating Bolt
Is it too much power removal?
Others may say they can't feel the effects
Isn't that already neutralizing static electricity?
Recently, Bridgestone and Michelin Radial have had a conductive Slit on their Radials
You can see the conductive slit on the Left Side (STAND side) from the Center of the Tire
The effect will be less effective if that conductive Slit is removing static electricity
So check your Tire once!
View detail
Static Elimination Part 1
Aluminum Tape (Made in 3M) I'm doing a little static elimination at
Buy it as your next Items
Easy to replace The price is a bit high though
Aluminum Tape does not eliminate static electricity (I can't put it up.) Another advantage is that it can be mounted in place
View detail
Perhaps it is good - - -
I tried dubious Parts
Fitted on Inolon's Bolt
I did not understand the effect clearly because I fought other together
I think I'm probably getting better
I thought that I could also make my own if welding could be done I lowered the evaluation slightly from the price
View detail
Large strange
Quantity : We purchased 2 pc and installed 1 pc each on the engine oil inspection window lower side and water pump side. Engine braking became Mild, Shift was also replaced with Smooth and Engine oil (Usually 3000 km) Shift change is Smooth even after past. View detail
Large strange
We already installed several places. This time, I bought it for Front Fork. Anyway, it's easy to install, I think that it is a product that you can experience quickly View detail
Large strange
I installed it in Throttle valve. Especially the ruggedness improved (Some people may be too sensitive) And above all, there is no valley in the low revolution range and I am satisfied with TorqueUpLarge. View detail
Fits: YAMAHA Majesty S (SG28J), YAMAHA Majesty S (SG271), YAMAHA SMAX 13.6- (SG28J), YAMAHA SMAX 13.6- (SG271), YAMAHA SMAX 13.6- (SG28J), YAMAHA SMAX 13.6- (SG271)
It's amazing!
The place where the effect is different depending on the type of car was different. Motorcycle carried 3 cars 2 cars.
Attached to carburetor and Injection. The exhaust sound changes from Idling, the skill improves from low speed, the starting acceleration increases Smooth, Torque increases and it feels strong.
Sas is like being stepped on a carpet, fine movements are effective and an elegant ride is surprised.
I do not remodel it, but I feel like I can not say this feeling that I made a remodeling. It is an invention that changes the history of vehicles.
If you do not properly verify the mounting location, it will not affect this difficult principle, so I think that it is better to ask the PRO how to do it better.
View detail