Reviews
Can be used for DUCATI SS and Initial ModelMONSTER S2
It can be used for the 900SS, 750SS, and Initial ModelM900 of the 90s. Many of the exteriors for older models are no longer available, but we appreciate your support. View detail
Maybe it's an individual difference, but …
I thought it could be installed as it is because it is the same shape as OEM parts, but it is not the same as Tire. The Clearance is only a few millimeters, so if you lightly press the Fender from above, it will interfere with the Tire. I'm done.
I don't think it will interfere if you don't push it down, but it's obviously narrower than the OEM. I'm going to use Spaceretc. to get a gap.
In addition, the shape of the screw hole is hollowed out for the head of the screw in the OEM, but it is different from the OEM. If you are worried about the damage around the screw head when you tighten it because it has only a screw hole. is a caution.
The surface is a nice mesh Carbon but I don't care because you can't see it. The handling of the side was quite appropriate.
Because of the individual differences, there is a little bit of fitting difficulty. I think it's a good product because hopefully it can be changed to Carbon in the same shape as the OEM.
View detail
Fits: SUZUKI For GSX-R1100 upside down fork, SUZUKI For GSX-R1100 upside down fork
NOT THE ITEM IN THE PICTURE
The item in the picture is not the item i received,if i wanyted a fibreglass guard i would have purchased one in my country for half the price,the photo is dishonest and misleading,,the guard is good quality. Not happy View detail
There was distortion. Individual difference?
I purchased it with reference to good evaluation of COSPA.
Quality is satisfying with price.
The texture of Carbon is beautiful.
However, when I installed it, something does not work. If you look closely well FenderBody has some distortion Quantity : Pair (for Left and Right) There was a difference of only a little less than Mounting Bolt of. Although wearing was possible as it was, it was not convinced, so I looked at it from the front Left Side Biting Spacer on Mounting Bolt Quantity : Pair (for Left and Right) Hitoshi etc. It was mounted at the height of. Result Calm down to the feeling that distortion does not matter. A person who needs Quality of OEM Product needs a little care.
View detail
The price
OEM Replacement Type, but the width and mounting hole position did not match. For width it is possible to install if it is prepared for deformation, but it is safe to put a thick RubberWasher or something in the gap between Body and Fork. I am one Side 5? (Quantity : Pair (for Left and Right) I wrote a Rubber Seat of 1?). Even this still has some margin (>_<). As soon as you set the taking hole as it is, it gently becomes an off car Fender Since the position became high, 2 on the F side and 2 on the R side. 5? I opened the hole upwards and managed somehow normal installation. Since the original size was adjusted, the original hole on the F side can see an elliptical shape that has been scraped, but now it is one so I will refresh the lower part of the Fender side as well (T_T) It is cheap and its shape is not bad with the OEM but it can be made a bit better ~ " (-""-) " View detail
Large whispering yoji ...
By saying "Other Company Product", it is clearly stated as two Nuts, but I hate direct Nut hitting Carbon fender, I removed Bracket from OEMFender and ported it perfectly to Front fork etc. etc. Despite being tightened to, the Tire clearance before and after is Quantity : Pair (for Left and Right) Asymmetrical and immediately removed.
I sent a wearing image and asked for a replacement but I am sorry to refuse Bassari when I can not exchange after processing.
Material : Carbon products are prepared to individual differences, but just spreading the mounting hole in the hole of OEMBracket has no reason to cause a whirlpiece, which is not unpleasant, but I will never buy it again. Those who buy it because it is cheap are advised to check with the Manufacturer recommended way of attaching and checking if there is a whirlpool and to put in Objection.
View detail
very poor finish on the rear hugger . marks and dimples in the finished carbon face . cut marks on the finishing edges . would advise to spend that bit more money and get a quality item instead of a very cheaply made product .
very poor finish on the rear hugger . marks and dimples in the finished carbon face . cut marks on the finishing edges . would advise to spend that bit more money and get a quality item instead of a very cheaply made product . View detail