Reviews
Radiator guard
Radiator is protected by Ganjisho.
This one won't bend.
Easy to install
View detail
Is it big but surprisingly lightweight?
There was one Bolt hole Gap because it was made overseas after all.
Side Stand interferes with the stand, so a cut is required.
Style is great, and the water pump cover is GOOD!
View detail
Flexible with 8mm thick plastic
The reason for purchasing this product is that I can cover the W/P and it is a Large pattern.
Requires kanhang for installation
The side stand bracket interferes with the side stand bracket, so the interfering part needs to be cut off!
It is fixed with 6 Bolts, but the holes of the middle Bolt are not aligned.
I machined it into a long hole.
View detail
Off-road driving with peace of mind
Driving a water-cooled vehicle on a forest road is a
I was nervous about not breaking the Radiator when I fell.
From among the Parts you searched for, you will find
I chose this one, which looks sturdy.
With these Parts, you can rest assured.
I think the Guard will stand up to a few falls.
In fact, I've been playing around with and knocking down a lot of stuff on Off-road.
Radiator is fine.
Installation is done after temporary fixing and proper positioning.
If you tighten it, it will be attached without any problem.
View detail
Thick.
The boards are thick enough to be effective in guarding against stepping stones and wood chips.
I feel that it is not strong enough to support the weight of the car.
No modification is required, but it is recommended to prepare a drill to make the holes larger.
The board is placed close to the Engine so that vibration and sound can be felt.
View detail
Fits: HUSQVARNA FE450, HUSQVARNA FE501, HUSQVARNA TC125, HUSQVARNA TC250, HUSQVARNA TE250, HUSQVARNA TE300, KTM 125SX, KTM 250EXC, KTM 250EXC-F, KTM 250SX-F, KTM 450EXC-F, KTM 450SX-F, HUSQVARNA FE350, HUSQVARNA FE250, HUSQVARNA FC450, HUSQVARNA FC350, HUSQVARNA FC250
To protect the Radiator
Motorcycle is on a HUSQVARNA TE250 2017 model.
The main use is for forest road touring and courses, not for flying like the Enduro or G650 XCOUNTRY, but for riding slowly on forest roads, over difficult terrain, hill climbing, etc. It is a bit more famous than the Hard Enduro.
Because of this, I was very worried that I would knock the Motorcycle over and damage the Radiator.
That's why I bought this product.
It's not difficult to install and it protects the Firmly and Radiator.
In case of a small fall, the Guard will protect the Radiator well.
I had a very good shopping experience.
View detail
Since the OEMs are unreliable.
The OEM guard is thin and unreliable, so I chose this one. water pump, oil filter, LINK etc. are also guarded, so I think it is very safe.
But apparently the OEMCenter Stand doesn't attach when this is installed? It seems to be.
I'm happy with it because it makes my Parenthesis look better and gives me more of an Adventure feeling.
View detail
For Radiator protection
The instruction manual is very difficult to understand.
There are only a few parts, so you can assemble it the second time without a manual.
I don't think there will be a second one, though.
The construction is not as robust as it could be, so I'm not sure it would stand up to a hard fall.
I think it's fine if it's just a standing moss.
View detail
I'm not sure if it's an individual thing or not.
When Guard was installed, and Right SideShroud was installed, the installation part of the rear of Radiator guard interfered with Shroud, and when it tightened with Bolt forcibly, the interference mark of White muddy color was attached to Shroud. After that, I defeated File until it did not interfere with File. View detail
accuracy
I'm sure it's a hit or miss for each individual, but my individual was a Ha Gap.
The accuracy of the assembly is on a trial-and-error level, and the detail processing is crude.
For those who like IngenuityLarge, you can Recommendation, but for those who are unhappy with not being able to pontificate, the assembly is Large, which could be Stress.
View detail
Pretty good
Personally, I would give it a near perfect score
Something about Fitting was bad, the Review said, but Balance the Bolt If you close it well enough, it will fit!
The past Reviewers have been terrible at putting it on or no problem at all
View detail
No problems with installation
I bought this one because the Radiator was bent with my previous Guard It was not difficult to install There is no problem with the basic function of the bike, but if the motorcycle falls down, it may not be able to be installed on the lower side of the Guard is bent View detail
It's okay
A product that is not a correct answer but is not a mistake.
There is a place to hit a little Shroud. Since it is made overseas, there is also a sense of inevitability.
I like design and I am satisfied..
Installation was highly evaluated because it was easy without any problems.
View detail
It is easy to install.
Used in WR250R.
Right Side Exterior It was easy to remove it by removing the exterior panel only.
The system is also not bad and no need for processing.
If the price is cheaper a little more ...
View detail
I am confident that I can run with confidence
Until now WR has not so much moss on the Radiator side but purchased for amulet
I got impressed that attaching pon attaching good precision has come out. There seems to be strength.
I broke the Radiator once at KLX, but that Motorcycle has a Radiator on Both Sides
Either whichever falls it is highly recommended especially for KLX riders..
View detail
I am firm.
Because I was exchanging the Radiator with the Other Company Product, it was a feeling that processing was quite necessary to install,
I stopped installing.
Well, OEM Radiator probably will be attached with Bolt-on or some processing.
I think that it is good because the thing itself is solid.
View detail
Some processing was necessary
Because there was a part hitting Shroud at the time of installation, some cutting work was necessary.
Although it may be able to be processed even if it is adjusted well temporarily by adjusting it, I cut off the part to be hit just in case.
It is good that you do not need to remove OEM's Pla Parts.
Regarding defense power, it is still unknown because it has not overturned fancy yet, but I feel like I can expect it.
View detail
Fallen cannibals
It seems that it is also from other Manufacturer's, but I felt that this product was also good in installation precision and cospa at other people's impule so I bought it.
Easy installation The Instruction Manual was bundled, but it is easier for me to understand if the image is a bit clearer.
The picture of One point is pretty. (Lol)
View detail
Problem with installation Instruction Manual
With WR 250 R, since solo forest road Touring is Main, purchase so that it will not run out when falling. Just installation Instruction Manual is incomprehensible, so it was hard to install, but if you can understand it can be installed in around 30 minutes.
Remove Seat, Shroud and remove the claws on the Red circle of the image, the Yellow circle will come off and the Blue circle Screw will loosen. I put a Radiator guard in that Screw. Since the bottom Screw is short, use the included hexagonal Screw. Accessory "White parts and Screw" I used it for the image here.
View detail
I fell in love with the plastic.
Purchased here because it was somewhat disgusting if it was a Skid plate made of Gold genus.
I was aware that I read other people 's impressions, but Bolt' s Length is missing - It is iterative that others will not tighten if you tighten somewhere (Lol)
Give it up before Quantity : 2pc - Bottom Quantity : It is fixed only with 2pc.
Oil It is removing the Skid plate when exchanging.
Oil Because it is visible to be covered.
Reflected sound of Engine will be frozen in May due to the evil installed.
It was cold sweat as it broke somewhere.
View detail