Reviews
Cospa is quite good.
Anyway, cheap is the best Merit.
The quality is in line with the price, especially the bolt on each part is quite cheap. Be careful not to over-tighten the bolt, as it can easily be nipped.
It is by far lighter than the expensive bar end mirrors of DAYTONA and TANAX, so there is rather less anxiety about it falling off.
View detail
Minimum required visibility
Size is small, so visibility is minimal.
On the contrary, it makes you look at it neatly lol.
It only worked well outward, but I don't feel like I've widened it that much.
With normal Mirror, the arms are reflected to a large extent and the camera is scared, but this has been eliminated, which is what we were aiming for!
Quantity of Washer:Only 1pc. is sandwiched, but there is no interference with Axel
Adjustment is a bit of a hassle…I had to adjust the angle of the clutch lever because it was interfering with the clutch lever.
Well, the rest is definitely Parenthesis good lol.
View detail
A little wobbly, but … looks good.
I installed it on CBR400R.
The handlebar was previously replaced and installed with 16mm inner diameter separate handlebars.
It will probably loosen and fall off while riding, so it must be retightened.
There is a wobble.
If you're concerned about it, you shouldn't.
View detail
Rin Parts Rin Parts LED compatible rectangular blinker relay
Purchased as a spare for LEDs.
Blinker relay for MADMAX MADMAXLED is better in terms of texture
But it's inexpensive in price, so I thought it would be just right for Spare.
View detail
Functional Parts for a Bland Bolt
[How is it used?
For fixing Bolt of License Plate of SEROW250 which is used for mountain play.
Just by replacing the inorganic fixing Bolt with this product, it will look better, and it can also be used as a Net fixing Hook for when you have a lot of baggage. Two for the price of one. PARTS.
Was the one you received as per Image?
I saw a friend's Motorcycle that had already installed this product when I didn't know it existed yet. What is this aluminum color that looks like a very small version of the Tezuga?" When I asked him about it, he told me that it was a product installed for the above-mentioned purpose, so I immediately took a crack at Ideas.
The product was as per Image because of such a process of purchase.
Was the installation difficult?
The difficulty level is low because all you have to do is remove the bolt that was attached to the License Plate and install this product, and I think that anyone can easily customize this part.
How was your experience with it?
Most of them are free dress-up parts, but they are used for fixing the Hook of Net for Motorcycle when we carry a lot of luggage with Motorcycle, which happens a few times a year or not.
It is seldom used for functional purposes, but it is useful when it is.
Well, it's a bit of a duplication. Color Anodized Aluminum Collar Dress-upSmall things.
[Included Parts:were they on?
As you can see in the picture, each color Aluminum Collar, Cap bolt (length is about 20mm?), Nut, Nylon washer×2 and 1 piece of Iron Washer are included. and Nut and Nylon washer×2 and 1 piece of iron washer is 1Quantity:Set, and itsQuantity:Two Sets are included in the package.
[Was there anything that disappointed you?
My friend who used it before me bought the Red one, but after about a year or so the Anodized staining faded and it became just Silver, so he painted it Red with plasticolor and dyed the hollow side line White (it was exactly the Image of Zunga).
Anodized light colors may fade quickly.
Other items that would be helpful
Point and hang of installation
Even though the collar is sandwiched, it is basically a fixed Bolt. "Tighten with the proper Torque." I don't think there is a problem as long as the
"Loose and falling off." If you are concerned about the "Mere Old Man", it may be a good idea to replace the existing nut with a Lock nut.
[Availability and clarity of the Instruction Manual
No Instruction Manual, as noted above. Bolt & Nut+α for fixing So no problem.
It can be used not only for fixing License Plate, but also for fixing M6Size, so it can be used in various ways depending on each individual's Ideas.
[Notes]
Not particularly
[ITEMS TO BUY TOGETHER
Basically, no.
Bolt & Nut, Aluminum Collar, and Washer in Quantity:The set is complete, so if the purpose is to fix the License Plate, this product is all you need.
[Opinions and requests to Manufacturer
2Quantity:Considering that the Set costs about 910 yen, I would like to request a more UV-resistant dye.
View detail
Visibility is ◎ but certainly not water resistant & UV resistant
The quality is good for the price and the visibility is good, so it's not bad.
But it is certainly vulnerable to UV rays and rain lol Cokingetc...I think you should take your own measures!
View detail
SHINKOTire from MICHELIN Tire installed on ZOOMER Rear
Changed from MICHELINTire130/70/12 to SHINKOTire130/70/12, Front mounted SHINKOTire110/70/12 on Falken 12-inches. View detail
Mounting holes are perfect.
Fender Eliminator was converted to Fender Eliminator and a Reflector was added.
It is cheaper than other companies' products and the reflector itself reflects well.
I was worried about the mounting holes because of the low price, but the Number was installed without any problems.
View detail
Headlight
Worst dust Waterproof on the back side.
If you don't devise a way to deal with it, even though it's a supported product.
It is fatal that it does not
View detail
For a little Accent
I bought it because it was reasonably priced and looked interesting. I had a hard time deciding which color to buy, but I chose Blue. There are different types of cutting other than the color, so please be careful when you buy one.
There are no special precautions, but be sure to remove oil on the body side with Parts cleaner.
View detail
12VMONKEY installation
I installed it on my '01 AB27MONKEY.
I bought it because I thought it was a consumable item and the price was good.
It takes less than 5 minutes to install, just remove the side cover, remove the band that holds the Relay in place, apply contact lubricant, and replace it. The initial movement is solid, now if only it would last longer!
View detail
Good rear visibility.
The NSR50's mirror was tightened together with the thin Cowl Bracket, so it was shaking due to vibration and rear visibility was poor.
If you put it on the Separate handle, I think you will have different taste in looks, but I like the Bar end mirror better.
It is easy to be damaged by standing and falling, but it is inexpensive and easy to buy, so it is not a problem.
View detail
It worked normally
It didn't have the appearance rust or anything like that on the Net, but it is uncomfortably hard. I'm using it as is for now, but I'll try to OH it soon. However, considering the price, I think it's adequate. View detail
If you can process it yourself, that's good.
Quantity:I'm thankful that I was able to buy it for less than $1,000 for 1 Set of 2pcs. but it's only cheap. The sea-ring is not done properly and I did the sea-ring by myself using the Glue gun. Although the important LED is bright, it sometimes flickers by Idling, probably because of the relation of the voltage of Battery. It seems to be possible to make it to the position light etc. according to Ideas. View detail
It's for ZOOMER
I found in the Package that it is for ZOOMER, so it should be able to be attached to ZOOMER
It's hard to tell the difference between Brake and Position
I couldn't pimp a motorcycle that I wanted to put on, so I left it there as a hassle It is
View detail
Design and COSPA are good ,,,
Although Design and COSPA are good, the Bar End part can be taken easily with installation first! Screw of Bar End loosens unless it is to be tightened regularly. A crack comes in Grip rubber although it is not rainy.. View detail
I can not recommend too much!
Although it fixes with back lining Nut during installation, the foundation is fragile, as the base is tightened, the base has come off the base.
I managed to fix it myself but I had to raise Quality a little more though it was cheap!
Sorry!
View detail
good material but...
This is a well made part, but it is sized too small for the American Honda Ruckus head light. Maybe it would work better for other aftermarket headlights, but I could not use it do to not fitting my Honda Ruckus. Oh well. View detail
For when you knock down
I knocked down Motorcycle and hurt Inner of Front fork.
I regret that I should buy it quickly.
I decided to do this by cheap things.
View detail
Compact
Because the vehicle has changed, again repurchase.
It is easy to solve the License Plate Light problem in making it a Fender Eliminator.
Basically I only ride during the daytime, but the one I'm in trouble is License Plate Light.
I attached a separate formula, but I am not good enough.
Eventually I came back to this License Plate Bolt Type.
Again the appearance is clear.
After all, a little more light itself is wanted to spread.
View detail