Reviews
Rin Parts Rin Parts Square Type LED Reflector
I was looking for Tale lamp for expansion of Motorcycle variously with Net, Motorcycle parts Shop, etc., but after all I decided to purchase and install this RinParts Rin PartsSquare Type LED Reflector which I sold at Webike after all.
Motorcycle In front of it, Daylight and Blinker are lit up as Position Lamps, which is a reasonable self Appeal power, but behind Motorcycle, the tail Stop lamp is Position lamp and the Appeal force behind is too weak is.
This RinParts Rin PartsSquare Type LED Reflector Material : Quantity on Aluminum Base : Pair (for Left and Right) Quantity : 2pc. Set installed, I decided to install its Base on Rear Carrier of Motorcycle and increase the Appeal power to the rear.
In order to suppress solder peeling of the foundation by any chance due to vibration and overheating, rectify Diode (1000V1A) 1 pc. (Separately purchased 1 pc. 15) I put it in Wiring, but the top of the photo shows the Stop lamp lit - The bottom of the photo shows the Tale lamp lit. Especially no problem has been raised in the decrease of the light quantity and Appeal force behind.
Such a Lamp which had been installed before was supposed to be attached with the dimension to be refrained, but it was broken by a bump at the convex part of the fallen road surface and it was disconnected.
In anticipation of this, this time it is more Quantity than the previous Base width : Pair (for Left and Right) I made the dimension of 25 mm shorter, so that I did not destroy it the same way even if I overturned.
This RinParts Rin PartsSquare Type LED Reflector is a very inexpensive product, but since it is one time to replace it if it breaks it is not broken and there is nothing better to break.
This RinParts Rin PartsSquare Type LED Reflector is cheap so I am Quantity : 2pc. Set is used.
Moreover, because it seems there is no durability low because it is inexpensive, I use this RinParts Rin PartsSquare Type LED Reflector with confidence.
Installation of this RinParts Rin PartsSquare Type LED Reflector to the base part is also not difficult, it is not difficult, and although there are 3 wires, it can easily connect to a for BrakeWiring of the Motorcycle Body with the plug terminal etc. It is easy to install I think that it will belong to the category.
I attached this RinParts Rin PartsSquare Type LED Reflector and confirmed the lighting many times at night, but the Tale lamp looked like it looks like an OEM Product in the dark.
.
View detail
RinPartsMicro LED Blinker
I tried to buy this Rin Parts Rin Parts Micro LED Blinker Ver1 intrigued by the appearance cuteness, but the light emits a strong light rather than cute but dazzling.
Daylight - I think that it can be used for Position and Blinker, but it may be better to lower the amount of light a little.
Especially, always lighting Daylight - When using to Position, Body's Material : Since Aluminum Body is heated and it becomes hot, Recommendation for installation on a windy place where it is easy to dissipate heat.
Of course, I think that it is a good decision to lower the light intensity and limit heat generation.
The whole body of this Rin Parts Rin Parts Micro LED Blinker Ver1 is made of Material : Although it is made of Aluminum, since the LED element is designed to dissipate heat as it is weak to heat, it is a product that can be expected for durability if it does not get as hot as possible.
As a result of doing several lighting tests to wiring this Rin Parts Rin Parts Micro LED Blinker Ver 1, I saw the rectification diode on the Minus side as 1 pc. , Plus side branched into two lines and Daylight - I thought that it is just good to limit the light intensity and heat generation by connecting two rectifier diodes in series to Wiring for use in Position.
The same effect can be expected by using constant current Diode or resistance, but from the aspect of Cost surface and simplicity durability and suppression of heat generation, using three inexpensive rectification diodes I think that it is Simple to limit the current.
In addition, I saw the White lighting product of exactly the same appearance as this Rin Parts Rin Parts Micro LED Blinker Ver 1 at 475 yen at other site.
I do not know the reason for its cheapness, but there must be some reason for sure.
I will recommend to be used after being devised to suppress the heating value of Body itself which is interested in this Rin Parts Rin Parts Micro LED Blinker Ver1 including saying.
This Rin Parts Lynn Parts Micro LED Blinker Ver 1 is not sure where to make a maid in.
It is making, designing and price not like JAPAN.
Once installed in the Motorcycle, it is not easy to burn the LED, right?.
I think that it is necessary in advance.
Rectifier Diode is 1 pc in electronic parts PartsCenter etc.. I sell for 15 yen. (I use 1000V1AX 3 pieces)
.
View detail
I love them, because not just a mirror, they fuctioning as the bar end stabilizer too, reduce the vibration on my handlebar. The mirror is looks very nice, reasonable prize but good build quality. It's fit the low handlebar on my bike, and make the cockpi
I love them, because not just a mirror, they fuctioning as the bar end stabilizer too, reduce the vibration on my handlebar. The mirror is looks very nice, reasonable prize but good build quality. It's fit the low handlebar on my bike, and make the cockpit looks simple without ordinary mirror. View detail
RinParts Rin Parts Micro LED Blinker
【What made you decide the purchase?】
This RinParts MicroLED Blinker is an unusual Type LED Blinker among various commercially available Blinkers.
It's pretty cute, so I bought it.
【How was it actually used?】
While considering how to install it, it is occasionally lighting and playing, but this RinParts Rin Parts Micro LED Blinker is quite bright LED.
【Mounting was difficult?】
In order to install it, it will be to open a hole of Φ 10 mm or to use the existing Φ 10 mm hole, but I'm thinking where to put it.
We have not installed yet, but due to the structure the installation will be large and it will not be difficult.
【Please tell me the installation point and hang】
Since this RinParts Rin Parts Micro LED Blinker seems to be highly waterproof, it seems to be Large sturdy even if you install it without worrying even where it will hit the rain.
When installing, I think that installing in a good position of the wind street which is easy to dissipate heat and applying Loosen Tightening Lock tite to the Nut for fixing is Large Off Point.
[Is there anything I was disappointed about?]
As I knew, this RinParts Rin Parts Micro LED Blinker has only two wires, so I can only use either Blinker or Position lamp.
Although it is possible to make a circuit so that Blinker and Position lamp can be used together, Diode is required separately.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Since it is a point, since it is now, Wiring is still appreciated, it is possible to have Tale lamp, Stop lamp and Wiring of Minus line as three lines from the beginning.
【Have you compared items?】
I compared it with various Blinkers observed by Net and Shop.
This RinParts Lynn Parts Micro LED Blinker gives orthodox and elegant light.
[Others]
Still for a while, I do not have the courage and opportunity to install this RinParts Rin Parts Micro LED Blinker in the Motorcycle, but let me report it again with Impression.
.
View detail
★ It's pretty that you make it round and Small
【What made you decide the purchase?】
Round at love at first sight Blinker pretty Small (Lol)
There was no necessity, but I bought it because it was cute.
【How was it actually used?】
Small is pretty and pretty, it is a blinker that you can use firmly with a lot of light intensity.
I tried energizing test, but it is dazzling light when energizing 12V.
【Mounting was difficult?】
This RinParts MicroLED Blinker Ver 1 Body is a product that can be installed easily by inserting it if there is a hole of Φ 10 mm and tightening with Reverse side from Nut.
The power source draws a line from BlinkerWiring of Motorcycle and Quantity : Pair (for Left and Right) It is easy because it just connects so as not to make a mistake.
【Please tell me the installation point and hang】
Body of this RinParts MicroLED Blinker Ver1 is made of Material : Since it is Aluminum, if you attach it to the Aluminum part of Motorcycle or attach it to a place with good wind, you can use it with the intended cooling capacity of the product.
If you apply Screw Loosening Prevention Agent to Gold Made Nut that stops at Reverse side, it will be hard to loosen so it is safe.
In addition, we sell that genus Nut in DIY Heat resistant Material : If you replace it with PlasticNut, even if there is no Screw loosening prevention agent, its heat resistant Material : As you tighten PlasticNut it will be fixed while being distorted by stress Material : PlasticNut becomes very difficult to loosen.
[Is there anything I was disappointed about?]
Although I did not understand it by appearance, the exterior was for Material : It was heavily unexpected because it is Aluminum.
【Hope for Manufacturer - Please let me know if you have any improvement points]
The appearance shape remains the same, I think that it can be used as an auxiliary light for Daylight and Stop-lamp if there are products with different luminescent colors.
【Have you compared items?】
Compared to various Blinkers of other companies, but there is not any other CustomizationBlinker finished compactly more cute than this RinParts MicroLED Blinker Ver1.
This RinParts MicroLED Blinker Ver1 is a very simple, rounded and lovely Blinker, and as a LED Blinker it is a very cheap Blinker as well as more than other companies' products in terms of price.
.
View detail
RinPartsMicroLED Blinker
【What made you decide the purchase?】
Although I did not have any use purpose in particular, the moment I saw this RinParts MicroLED Blinker Ver 1 with Net I tried to buy it as a design shape I like very much.
【How was it actually used?】
Although we do only the energization test for initial malfunction confirmation after arrival, it is a very bright LED for Small size.
【Mounting was difficult?】
The axis of this RinParts MicroLED Blinker Ver1 (neck) Since the part is in the Bolt state with a diameter Φ 10 mm, it can be installed and fixed easily with the attached Nut by putting it in a hole of a slightly larger diameter than Φ 10 mm in diameter.
【Please tell me the installation point and hang】
The axis of this RinParts MicroLED Blinker Ver1 (neck) The part other than Lens of the exterior is Aluminum for heat dissipation, so installing it in a good location on the wind street makes it possible to urge the heat radiation more effectively.
Wiring is Quantity : There is only 2pc, but Position lamp (Daylight) If you use it for both Blinker and Blinker it will be possible if you use resistor and rectifier Diode.
[Is there anything I was disappointed about?]
Although it may be said as expected rather than saying it is disappointing, this RinParts MicroLED Blinker Ver 1 gets quite hot as a whole if you energize continuously for 1 minute.
Position (Daylight) In using it, I think that it is better to use practical use after putting in resistance of Large texture and looking at the heat generation of Body.
Also, when using Blinker, turn ON / It is alternating and it is not always translating constantly and continuously Body is hard to get hot so I think that there is no problem for usual use as it is.
【Hope for Manufacturer - Please let me know if you have any improvement points]
It is the LED of the same form as this RinParts MicroLED Blinker Ver 1, and I certainly want you that there is Daylight of White color, Tale lamp of Red color, Stop-lamp, etc..
【Have you compared items?】
Compared to the appearance of several other Blinkers, I chose this unique design of this RinParts MicroLED Blinker Ver1.
.
View detail
Rin Parts Rin Parts Square Type LED Reflector
【What made you decide the purchase?】
When extending Rear Carrier exclusively for Long touring, OEMTail lamp became hard to see, so we added a round Tail lamp.
Since the mounting base was overhanging too much and broke the round Tail lamp at the time of falling, improve this time to make the overhang small and look for a cheap and easy Tail lamp in a shape other than a circle If so, I found this RinPartsSquare Type LED Reflector.
【How was it actually used?】
Immediately, I tried installing.
Although there is concern about solder attachment peeling due to vibration, for now it plays a role well in tune.
At this price, Reflector - Tail lamp - It is surprising fact that there are three functions of Stop lamp.
【Mounting was difficult?】
Material for installation : Since we used Aluminum Base, it was easy to process and the installation was Smooth.
【Please tell me the installation point and hang】
On the core of the Reverse side of this RinPartsSquare Type LED Reflector there is Φ 5 mm Bolt for mounting.
Wiring comes out three lines near one end.
And since convex for fixing Body is out near the other end, Material : A total of three holes are required in the Base of Aluminum.
Because we need holes of about Φ 5 mm each, here Φ 5. Make 3 holes in 5 mm holes in required locations.
0. Since we can afford a margin from mounting error by responding with 5 mm Large eyes hole, we will be able to install properly when we fix this RinPartsSquare Type LED Reflector.
Millimiri kitchenly and Φ 5. Although it may be processed 0 mm, it is highly likely that it will not be entered at once with experience because of experience.
If it is easy to install it in a short time, we recommend that it be mounted and processed with error margin.
[Is there anything I was disappointed about?]
As of now, it is Items which can satisfy Large about price, capacity and quality.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I do not want peeling by Solder attached by vibration.
I want you to last long.
【Have you compared items?】
It compared with RinParts Round LED Reflector.
Just because the shape was different, both price and price were the same, so this time I chose this rectangular shaped RinPartsSquare Type LED Reflector.
.
View detail
RinParts Rin Parts Square Type LED Reflector
【What made you decide the purchase?】
Previously, with the Round Type LED Reflector attached, it was broken and damaged, so this time I tried this rectangular Rin Parts Rin Parts Square Type LED Reflector.
The price was also cheap, so Body was thin, so it was a product that seemed easy to install so I decided on this.
【How was it actually used?】
It seems to match the mounting base, so it looks bad.
The Reflector ability, Position and Stop lamp LED emission quantity are also good.
【Mounting was difficult?】
I did not feel difficulty in particular, but I installed it after considering the mounting dimensions and Wiring dimensions a little.
【Please tell me the installation point and hang】
Because it is a special Stop-lamp auxiliary light, we installed it to make it stand out even a little.
Also, in order to attach this Rin Parts Rin Parts Square Type LED Reflector to the Base, you have to open three Φ 5 mm holes of Wiring hole, fixing hole and rotation prevention hole.
We measure the dimensions and mark it and drill, but first open the fixation hole in the middle and pass it once, then Quantity : Pair (for Left and Right) If you reconfirm the hole position of the hole and drill it, you can install less Gap.
[Is there anything I was disappointed about?]
I installed it, but it was too normal.. I do not feel any discomfort.
It is a good thing that there is no sense of incompatibility, but it is too ordinary and it got somewhat unsatisfactory.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I want this product if it has the same shape as Rin Parts Rin Parts Square Type LED Reflector and it can be used for Orange color Blinker.
【Have you compared items?】
I tried to compare with other companies' LED tail lamps, but I liked this Rin Parts Rin Parts Square Type LED Reflector at the lowest price.
[Others]
This Rin Parts Rin Parts Square Type LED Reflector is a very inexpensive product but it is a normal Tale lamp with a very Sharp feeling of elegance when trying to install it without any cheapness.
It has a lot of light at the time of light emission so it is very bright so it can be recognized very well, it is a perfect product as Tale lamp and Stop lamp.
.
View detail
Rin Parts Rin Parts Square Type LED Reflector
【What made you decide the purchase?】
The cheapness of this RinPartsSquare Type LED Reflector = affordable price is a deciding factor.
【How was it actually used?】
There is no trouble, Position lamp and Stop-lamp are lit properly properly.
【Mounting was difficult?】
Material : I installed it on Aluminum Base
, This RinPartsSquare Type LED Reflector needed to drill three holes for Screw, Wiring, and fixed claws.
It was not difficult though it did not require too much precision, but it was just annoying.
【Please tell me the installation point and hang】
Apart from the hole for Screw, if you open it with a slightly larger grade, you can flexibly install it so you can easily install it.
[Is there anything I was disappointed about?]
This RinPartsSquare Type LED Reflector with Quantity : 2pc. Set purchased 1 pc. There was a lot of Wound on the reflective surface of.
I do not know whether the expression of disappointment is correct, but it is a fact that I felt like I was betrayed.
【Hope for Manufacturer - Please let me know if you have any improvement points]
My Motorcycle is an Off car so especially this RinPartsSquare Type LED Reflector attached to Tail will soon be full of Wounds at any rate ...
But, when it is brand new it is shock that the reflective surface is full of Wound. I want you to manage products properly.
【Have you compared items?】
Multiple companies (RinParts) Compared with the LED Reflector of the same function to sell.
But they were all Round LED Reflectors.
■ The square shows that the appearance of this RinPartsSquare Type LED Reflector is White and Red (Light is red color) There was only so, last time ● Round LED Reflector (Red) In some cases I was wearing this ■ This rectangular RinPartsSquare Type LED Reflector (Red) I selected.
[Others]
This RinPartsSquare Type LED Reflector for Motorcycle's Tail Quantity : Pair (for Left and Right) It attached to the Tail lamp's Position and Stop-lamp as an auxiliary light and it was better than the last round type for this RinPartsSquare Type LED Reflector's square ■ Tail part looks like Sharp and Parenthesis is good It became a feeling..
.
View detail
What is Slider?
Axle Slider, but because it can be used for various Bolt, Screw parts, as a Slider it feels the correct way to use it as Dress-up.
The price is cheap and easy to purchase is also a good point.
it's recommended.
View detail
★ cute ★ RinPartsMicro LED Blinker ★
【What made you decide the purchase?】
This RinPartsMicroLED Blinker Ver1 is a very Compact, Originality cute Design Blinker so I tried to use it once.
【How was it actually used?】
The light-emitting surface of this RinParts MicroLED Blinker Ver 1 is small, but it has a lot of light intensity and it is convex Lens so it has sufficient brightness.
Besides, since the Wiring section from Blinker Body has been subjected to a firm Waterproof treatment, you can safely install it anywhere.
【Mounting was difficult?】
I am Position (Steady light) And Blinker (Blinking) In the case of installation, when inserting the neck portion of this Rin Parts MicroLED Blinker Ver 1 into the hole of Φ 10 mm, it can be easily fixed using the attached Nut.
【Please tell me the installation point and hang】
It is very easy to install this RinParts MicroLED Blinker Ver 1 if you make the diameter of the hole for installation just a little Large.
In addition, the material of the same size as Nut of Gold belonging to used for fixing : If you bought Plastic Nut at your local DIY and use it instead of the included Gold genera Nut you can make it much lighter.
[Is there anything I was disappointed about?]
As I knew, this RinParts MicroLED Blinker Ver 1, Wiring is Plus (+) Minus (-) Quantity of : Since there is only 2pc, some modification is necessary so that it can be used for both Position and Blinker.
【Hope for Manufacturer - Please let me know if you have any improvement points]
In addition to the Orange emission color of for Blinker, if there are such as White color emission for Daylight and Red color emission for for Brake, I think that there are opportunities for future use in the future.
【Have you compared items?】
I compared it with various other LED blinkers.
The function of this RinParts MicroLED Blinker Ver 1 is nothing to replace, in particular, compared with the various LED blinkers of several other companies compared, but the appearance features are strong because the Originality is strong and it is pleasing.
.
View detail
★Square Type LED Reflector★
If you add Rear Carrier and install Large Capacity Rear box, it will be difficult for the Stop lamp to confirm from the following car with a high car height, so use this phosphorus PartsSquare Type LED Reflector to assist the Stop lamp Add lights (repair) Did.
In detail, similarly, the previously added Round TypeStop lamp (● ● ●) Quantity is : Pair (for Left and Right) It was 20 mm long, so Left bounced backwards Willy barely struck the ground and it was destroyed. (Overloading also causes)
This time, Base is Quantity : Pair (for Left and Right) 20mm (Total 40 mm) Shrink and renew this PartsSquare Type LED Reflector (■ ■ ■ ■) It was a repair that I used to repair.
Although it takes time and effort to restore, this phosphorus PartsSquare Type LED Reflector is very cheap and easy to enter, so repair costs are not to be Large.
Quantity : 2pc. I bought it but 1pc. It was a pity that the reflective surface of the Wound was full of Wound, but I used it as it was no problem with the lighting state.
There is a rumor about solder peeling, but I am a competitor (Suzuka Cere ○ ○. ○ Mr.) was actually experienced with expensive LED products.
(The product did not improve so easily and repeatedly returned and exchanged repeatedly. )
However, even now the reason for that is long-lit (Position) It can be inferred that solder will be easily peeled off due to heating and continuous vibration.
In response we can lower the heat generation temperature when Position light is emitted by lowering the current lower than the prescribed value, so in case of emergency, bite the rectifier Diode between Wiring of this phosphorus PartsSquare Type LED Reflector came.
Luminous power will be reduced a little, but rectification is insurance against durability so it can not be helped.
Still, this phosphorus PartsSquare Type LED Reflector (Quantity : Pair (for Left and Right) As shown in the picture, Motorcycle's MainLEDStop lamp (Photo Center down ▼) It is the amount of light that will not be defeated.
This picture is in the Position state, but the Stop lamp glows brighter more.
Because the color of light looks the same color, it does not feel strange at all..
Although it will not be destroyed in the future, even if it falls down, I improved rectification to a strong durable size and also applied rectification insurance, but I think that it is the most important mental attitude that does not overturn with overloading.
safety first
.
View detail
Recommendation to those who keep in mind the details
The price is reasonable price
Wheel It can be attached easily without detaching.
Recommendation to people who want to customize to One point and small places
I chose Gun meta
View detail
Design was good so I bought it
Design was good so I bought it.
Black was out of stock, but we got ordered.
The effectiveness of Brake also stops with a cut.
It is unknown whether it can be installed with Wheel for DIO.
Incidentally, it was necessary to process when installing 190 mmdisc to Wheel for DIO.
View detail
It was good as it does not look like a cheap
It was good as it does not look like a cheap.
I chose Black, painting is also fair.
It is good enough not to compare with OEM.
Design is also good and is a Recommendation.
View detail
It was surprisingly unexpected.
It was a little uneasy as the price was cheap, but the structure of the goods that arrived, the structure is so firmly.
However, I felt Mirror's quality was not very good. Cut face of the edge can be seen through.
I have not used it in the long term, so I hope it will not break ...
View detail
★Reflector★Position lamp★Stop lamp
I am on HONDA's CRF 250 L.
Rear is a Fender Eliminator and Stop lamp is also exchanged for Other Company Product.
Further extension of the OEM's Rear Carrier so that the Rear box is to be placed behind, since the Stop lamp became difficult to understand from the back ‥
I thought that this was dangerous I brought the Bracket out from the Rear Carrier extended as an auxiliary light for the Stop lamp and made Base and increased the auxiliary lamp Stop lamp.
I also secured cognitive safety from the back and loaded a lot of luggage and went to Hokkaido Touring where I got overloaded and Motorcycle collapsed on the STAND side Left diagonally backward in Willy state, Stop lamp destroyed every BaseGold object.
After returning home, to repair it, this time I use this phosphorus PartsSquare Type LED Reflector to rebuild the ■ ■ auxiliary lamp Stop lamp, but in order to install this phosphorus PartsSquare Type LED Reflector, it is a little less than Φ5 mm for the BaseGold object Large I have to open three holes.
(1) Body fixing M5 hole for Screw to pass through (Nut fixed)
(2) Wiring (BlackRedGreen) Hole to pass
(3) Body Insert the ledge behind the body to prevent the body from turning
I found the vibrating base etc. etc. I thought that I could wipe out the worry of solder peeling as a vibration mitigation measure, when further fixing the body Cushion (1mm) I use Double-sided Tape with BaseGold thing.
While carefully devising and devising this Rin PartsSquare Type LED Reflector we are Wiring, but unfortunately it will immediately destroy depending on how to overturn.
If you are saying such a thing, you will not be riding a single car, but safe driving (To not topple over) I have never tried it..
It is safe behavior for me to install this phosphorus PartsSquare Type LED Reflector as an auxiliary lamp Stop lamp.
Those who feel that it is difficult to recognize Stop lamp from behind your own Motorcycle, by all means this Rin PartsSquare Type LED Reflectoretc. Use Safe for backward Appeal (Auxiliary lamp Stop lamp) How about trying to expand?
Although there is a fear of breakage destruction due to the durability of the product and falling, in order to reduce the fear and the probability that you and Motorcycle will collide with the following car from the rear, it is absolutely necessary backward Appeal.
It is too late since the accident happened.
.
View detail
★ ☆ LED Reflector ★ ☆
This RinParts Rin PartsSquare Type LED Reflector has 24 built-in LEDs.
As you can see from the Left, there are 4 vertical - 3 vertically - 4 vertically - Vertical Quantity : 2pc. Set - 4 vertically - 3 vertically - It has become an array called vertical 4.
The middle is vertical Quantity : 2pc. Because it is only Set, I feel a little discomfort.
This RinParts Rin PartsSquare Type LED Reflector, Wiring is the three colors BlackRedGreen.
As usual, Black's Wiring is Minus (-) is.
Green color Wiring is Position lamp, Red color Wiring is Stop-lamp.
The light quantity of Position lamp is 7 in Stop-lamp / It is about 10, both of which are bright enough.
This RinParts Rin PartsSquare Type LED Reflector is new but Reflector (Light emission) There is a lot of Wound on the surface and the arrangement of the LEDs is vertically only in the middle Quantity : 2pc. It is somewhat mindful that it is only Set, but it is not particularly a problem of Large.
Functionally, 24 LEDs play the role of Position lamp and Stop lamp well, so only durability is the problem.
As in other people's Impression, this phosphorus PartsSquare Type LED Reflector vibrates etc etc. The possibility of solder peeling of the inner base can not be denied by.
Even though it is cheap, the labor of the installation work is not proportional to the price of the goods.
With cheap worse or bad, replacement work can be troublesome.
We are assuming that it will overturn and break, but we are prepared for breaking or repairing, but we are honestly capping the foundation peel without relation to impossible to exchange goods or cheap price. I want it..
Even if it is slightly expensive, it does not matter if the quality is bad a little, but it is not easy to just have durability even if it is cheap.
(There are also expensive and durable products in the world, though. )
In order to confirm the initial malfunction, I tried to energize this phosphorus PartsSquare Type LED Reflector and light the Position lamp and Stop lamp, but there was no particular abnormality.
At the moment there seems to be no bug related to durability.
This phosphorus PartsSquare Type LED Reflector thinks that it is a product that is not so bad for price as long as it can confirm durability.
I feel corporate effort at this common price.
.
View detail
Rin Parts Rin Parts Square Type LED Reflector
This Rin Parts Rin Parts Square Type LED Reflector's Largest Large Attraction is Destructive Cheap (Lol)
Rin Parts Rin Parts Square Type LED Reflector is suspected of peeling Solder on the basis of cheap price, but it is common in troublesome peeling of Solder from the foundation even for expensive products in the world.
It is possible that it will be too bad.
It is a preconceived prejudice that seems to be bad just because it is cheap.
This Rin Parts Lynn Parts Square Type LED Reflector thinks that the three points function of Position lit, Brake lit and Reflector are condensed and it is more than the price.
Due to product management problems, there were many Wounds on the reflective surface, but that is a different story from the capabilities of this Rin Parts Rin Parts Square Type LED Reflector.
Because this Rin Parts Lynn Parts Square Type LED Reflector is cheap, it is a promising pleasant feeling that you can carefully attach and wired and handle various experiments.
Moreover, since it is LED emission, it is a flashing flicker, it is a strong straight light, so Merit is easy to recognize and confirm the red color of the LED even from the far side.
For the destructive cheapness, it is a solid Reflector that can not be destroyed so it even feels external toughness.
The firm making is becoming a calm existence as if it is attached to the Tail of Motorcycle and it is felt as a conventional product.
Backwards self Appealetc. Stop lamp for - We recommend that you purchase this Rin Parts Rin Parts Square Type LED Reflector by all means when adding Tail lamp.
Because it is a cheap and easy-to-install product, Customization can be added even for beginners.
.
View detail
Rin Parts Rin Parts Square Type LED Reflector
The dimensions of each part of this Rin Parts Rin Parts Square Type LED Reflector is ‥
Reflector dimensions are 84 mm X 30 mm X 3. 5 mm, Base dimensions 91 mm X 36 mm X 6. It is 5 mm.
Reflector (Light emission) Together with the base and base thickness is 10 mm.
Product information at the time of purchase includes Size : It was about 89 mm X 35 mm X 10 mm.
I trust the publication dimensions of this Rin Parts Lynn Parts Square Type LED Reflector, and in advance to use it as a mounting base, we are going to use a 35 mm wide Material : I bought an Aluminum Flat bar for 1000 yen, but the dimensions of this Rin Parts Rin Parts Square Type LED Reflector arrived at hand are slightly smaller (1mm) Because it was different, Material purchased for 1000 yen for installation base : Aluminum Flat bar has become useless shopping.
Since the posted dimensions and the actual dimensions are slightly different, please purchase on that point of consent.
It is unavoidable that the price is cheap, but Reflector (Light emission) On the resin surface of the section there were a lot of Wounds that I could not think of as a brand-new product.
It is a product with product management problem.
I am trying to use this RinPartsSquare Type LED Reflector as an auxiliary Lamp for the Off-road motorcycle Stop lamp, so it has become such a usage that it will be full of damaged Wound or broken by several falls So, Reflector (Light emission) I used it even though I used Wound all over the place ...
Surely, I think that most people who care about Wound are worried, I think that it is WoundLevel which will surely accept you if you ask Webike for an exchange.
In any case, this Rin Parts Rin Parts Square Type LED Reflector is an item not under product control, so if you would like to purchase and a little difference in dimensions and Reflector (Light emission) Those who are concerned with the Wound of the surface recommend that you exclude this RinPartsSquare Type LED Reflector from the target from the beginning.
I will destroy it immediately by Dirt driving, so this Rin PartsSquare Type LED Reflector, which is cheap and easy to obtain with this finish, is enough.
I think that it is a good product if it can be used for more than 1 year.
.
View detail