Reviews
Fits: SUZUKI GSX750S Katana, SUZUKI gsx1100s katana (sword), SUZUKI GSX750S Katana, SUZUKI gsx1100s katana (sword)
Replacing the Cell Motor while replacing the Cell Motor.
Replacing the Cell Motor while replacing the Cell Motor. View detail
I think it's a little expensive….
The construction is not bad, but the price is a little… expensive.
Red Anodized will fade in time as it tans.
The combination of brembo's s50 oil tank and brembo's CORSA radipon is a bit hard to handle the Hose.
For the high price, there is not much flexibility in adjusting the position.
View detail
It looks nice.
It is a hassle to put the Wire Stopper in the Clutch holder. View detail
It's a must have Sticker for KATANAAnniversary. 、、、、、
Tank Sticker is a must for KATANA 90th Anniversary.
I thought about buying a new one, but it was sold out as an official SEA BASS Parts.
I had no choice but to make my own, and then I found them at Webig! I was so thankful and immediately bought two of them.
When the original Sticker was removed and the purchased Sticker was applied, some of the print on the edge of the transparent Seat was taken away by the transparent Seat when the transparent Seat was removed.... As a result, a part of the print was peeled off. It was brand new.... I am very sad, even though I went to a lot of trouble to buy it.
I'm patient now.
View detail
Is the reduction effect small!
To replace the OEM Clutch Lever, it is necessary to remove the Bar End, Grip, and Switch Box, and it is necessary to be prepared to replace the Grip depending on the situation. We tried to install and adjust it in combination with Unicorn Japan's 2-way clutch release arm, which was introduced earlier, but we could not feel the effect as much as the combination of OEM clutch lever and 2-way clutch release arm. I did not notice much effect compared to the combination of OEM Clutch Lever and 2-way clutch release arm. I think it looks a little better, but I have to evaluate that the cost performance is low. View detail
Fits: SUZUKI GSX750, SUZUKI GSX750 , SUZUKI GSX750 , SUZUKI GSX1000S, SUZUKI GSX1100S, SUZUKI GSX1000S, SUZUKI GSX1100S
Required for MeterRepair
Meter needle fading and needle breakage due to aging are inevitable, and OEM parts are difficult to obtain. It's a real itch that needs to be scratched." I would not recommend that you easily try to replace the needle with a meter needle, as it requires a certain amount of knowledge and skill. Also, the cost is a little high! I wish they could do something about half the price. View detail
Spoiler
Very expensive for what it is. Why is there no carbon fibre option? It is so tiny and just made of plastic costs so much and doesn't even come painted. But it does make my bike look good. So oh well. View detail
Things are good!
Things are good.
It's normal, tightly Cut-out&Black processed, and it's working well!
But it's still expensive.
View detail
Fits: SUZUKI GSX1000S KATANA (KATANA), SUZUKI GSX1100S KATANA (KATANA), SUZUKI GSX750 KATANA
Installation is complete.
I had to shave a lot of parts to be able to install it. I would recommend buying this product on the premise that you will have to shave the interfering parts yourself from the start. View detail
Fits: SUZUKI GSX750S Katana, SUZUKI gsx1100s katana (sword), SUZUKI GSX750S Katana, SUZUKI gsx1100s katana (sword)
It's a shame
I was confused with other products, but I decided to use Onospeed with reference to the price and other people's reviews.
When I checked the product, the mounting part of the Nut was burnt weld and was completely black,...
That's a shame, I treated it with Compound to polish it up.
There was another BALI on the One Side where the Axle Shaft goes through,...
Processed by Bar File.
The rest of the dimensions were perfect with no heat deformation from welding.
If the details were handled, the Design would be great and it would be a perfect product.
I hope the quality will improve.
View detail
Fits: SUZUKI GSX750S Katana, SUZUKI gsx1100s katana (sword), SUZUKI GSX750S Katana, SUZUKI gsx1100s katana (sword)
Ohno Speed Stainless chain pull
Material:The texture peculiar to Stainless Steel is astringent and Parenthesis is good.
The BALI, chamfered, is a solid product and a finish that will satisfy the Gold genus fetishist.
However, the cost performance is low.
View detail
The range of motion may be too wide.
It is good that the pull on the Clutch has become lighter, but the pull range has become wider (Large). (It is a matter of course) Therefore, it is possible to pull Lever farther to Quantity:Because it has to be set, and my hand is not so large, it becomes somehow difficult to handle. It is the main point of view.... View detail
Brushbo effect
Quantity with Durable Race:Pair (for Left and Right) It seems that the purpose of the Parts is to open to the Wheel and remove it easily
When I picked it up, the Spring force was weak and it felt like nothing was going to happen, but it was a good Pad away from the disc and the dragging feeling was gone
I'm not able to discern which one is more effective, since I'm also doing a Caliper wash, so I may just be wondering But..
I think it works because they sell this weird stuff
it is attached to the brembo sand, but it can be assembled with Pad spring, but it opens with this I'm sure it's not easy to get an effect, so it's probably not the right one. After the photo, I took the board Spring
View detail
Maybe you could even make your own
the brembo 4 potCasting caliper doesn't have a lot of Pad dragging ?
I was the same way
I would try to rub it out to see what I could do about it, but I couldn't get rid of it
I bought this to try it out and put it on
It feels softer to the touch in my hand than I expected, and I have to admit Are you sure this thing is large enough? I was under the impression that..
LargeIt's sturdy!
And the dragging of the Pad is a nice touch!
Cleaning the Caliper makes it easy to remove and install the Pad pin
But this one is stuck in the remaining thickness of the Pad and stays in place
When the pad is getting low.. ・ Wouldn't it get stuck between Pad and Rotor? I'll try to worry about it
Well, as long as you check it often and replace the Pad as soon as possible, there's no problem
Also, the material is Stainless Steel piano wire (spring wood) 1.2φ about
I sometimes make my own Bus fishing lure, but it's just about this thickness (a little more (Is it thick?) I have the Stainless Spring material of
If you buy one and pay this Gold amount, how many cars could you make if you bought the materials for this Gold amount? Huh?
Since we're playing with the Motorcycle at our own risk anyway, is it possible to build our own? I think about it
(Sorry, Webike, I'm sorry But I'm not trying to interfere with product sales.)
Spring material is hard and bending it is Large strange, though
If you want to get rid of the pad drag of the casting caliper, make a sample and get the same kind of product If you want to make your own, I might recommend it
View detail
Fits: SUZUKI GSX1000S, SUZUKI GSX1100S
Buy peace of mind
Material : Because I am using Stainless Steel's Wire, I think it is harder to grow than OEM Parts Number and it is hard to cut. Is not it a high-priced item, is not it a bargain in the sense that it buys relief?. View detail