Reviews
very good
Because it is Exclusive Design, it was possible to install it easily. However, the presence of the tail goes up because it is a bit larger than OEM. (≧▽▽) (≧▽▽) View detail
A few more beautiful than the OEM tail lamp?
A seven year old GRASS TRACKER
The Handlebar and Tail lamp that were not so good
exchange
Male car's tail lamp
Was that right? Was it?
View detail
Combination Warning
I wanted to make the area around the rear amps Compact and replace it with the OEM Bracket I bought it because I thought it would be easy to do
Under normal circumstances, the effect would have been as expected, but due to the following conditions, the result was It was very difficult to install
Combination with a rear carrier
I had installed a rear carrier as a retrofit, but it is incompatible with this product When you install this product, you need to bolt three upper parts and one center, but the upper three parts are not compatible Tandem seat, Rear carrier and the material in question:Three FRP brackets need to be fastened Among them, the rear carrier needs to be mounted at a delicate angle, and if it is not, it will not be able to be fixed at all I couldn't get the Screw in the middle of the two places to fasten In addition, in my case, I have a separate ETC body on my rear carrier and the cord Please be careful if your vehicle is equipped with the Carrier It is
Combination with License PlateFrame
When you are using a License PlateFrame, the Number doesn't fit perfectly It is designed to fit the dimensions of the License Plate without a Frame If it is removed, it is early, but because I wanted to leave it daringly, I shaved the Bolt hole of Body a little I installed it by biting the Rubber on the part that floats against it
There was an unexpected Trouble, but Harness of Exclusive Design It's really just a matter of connecting them together and achieving the Compact look without being unnatural
If you understand the above, you will get the results you expect
View detail
Just size
I've tried a couple of tails that fit my current Seat Cowl, and I've settled on this one!
For those who are looking for a middle size that is not too large and not too small, although small processing is necessary is good
View detail
Truly Male car!
Wiring is hard to see, looks good, good texture with the License Plate base is good.
Just not being easy to install, Design seen from directly above, Top mounting Bolt is dirty.
After carefully allocating Torque, I mounted it and tried running and the top mounting Bolt was gone.
Originally a bad Bolt so bite RubberWasher and fix matte Flange bolt with UNut.
After that, it was decided to replace it as soon as it was running out in about a month.
There will be individual differences, but vehicles containing solid sediments require careful attention to installation and bulletproof.
But I think that it is good from Lineup of Male car if you exchange Tail lamp of 250 TR.
View detail
Tiny
I installed 250TR for Cafe racer. OEM's Tail lamp was lavish with a large bracket attached, so I replaced it for it and it made it clearer. The installation was easy with only changing the coupling. Since there is no reflector attached, I purchased a reflector separately from the Male car and installed it. View detail
Compared with a NORMAL, it is a size of the increase of 20~30%. attachment is easy. The bolt nut of a sheet, a Lamp Stay, and a Tail lamp is removed, a Coupler is substituted, and the rest is as a bolt nut is attached. Although there is not a d
Compared with a NORMAL, it is a size of the increase of 20~30%.
attachment is easy.
The bolt nut of a sheet, a Lamp Stay, and a Tail lamp is removed, a Coupler is substituted, and the rest is as a bolt nut is attached.
Although there is not a
description, it is exchangeable in 10 minutes.
The atmosphere which is freely different using the Stay of the
NORMAL can be experienced.
It is although it is however worrisome that the Plating portion of a pedestal is a little wavy.....
View detail
Exchange can be easily done for the Tail lamp of Z2 look. Although there was no attachment description, I think that the direction which a sheet can remove is made by itself. Since wiring to the Coupler was attached, it is a Bolt on. Structure of
Exchange can be easily done for the Tail lamp of Z2 look.
Although there was no
attachment description, I think that the direction which a sheet can remove is made by itself.
Since wiring to the Coupler was attached, it is a Bolt on.
Structure of
details is also solid and it is one satisfying article.
if compared with
pure Tail lamp -- very -- it becomes large and the impression from back also changes.
It is
recommendation.
View detail
Since the pure Front Rear fender of 250TR was exchanged for the product made from OSCAR, the Tail lamp of the Manufacturer was purchased. Although there was several kinds or a Tail lamp, the basic Lucas type was chosen. Since this Tail lamp can carry ou
Since the pure Front Rear fender of 250TR was exchanged for the product made from OSCAR, the Tail lamp of the Manufacturer was purchased. Although there was several kinds or a Tail lamp, the basic Lucas type was chosen. Since this Tail lamp can carry out [ LED ]-izing as an Option, I would like to LED-ize later. Attachment of a Tail lamp is very easy at a Bolt on. View detail