Reviews
It's hard to close.
If the handle is not intentionally hooked inward when closing, it may not be properly tightened and locked.
Quantity Lever to occupy the lid:It is often frustrating because it often doesn't Set and lock instantly.
The capacity is sufficient to hold a full face in Size XL and +α to hold other things.
View detail
Looks good, but doesn't help! LOL.
First of all, the bar is too thin to fit a Smartphone Holder or an additional Meter Bracket etc. The clamp part of this Handlebar Brace has a sharp corner and is dangerous if it is hit in an accident, so I replaced the clamp part with a Posh one to match the Handlebar. I am currently using a PoshHandlebar Brace because it is inconvenient to use a Holder or an additional Meter, and the Handlebar vibration reduction is not effective. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA
It sticks out the back.
It is larger than expected, and when installed on a MONKEY, it extends behind the body of the vehicle.
The volume is lowered to a tolerable level when the inner baffle is installed, but the sound seems to be sluggish.
Swing Armetc.NORMAL car rating should be careful.
However, I think it is well made for the price.
View detail
As a Leg shield for CUB PRESS
It's deformed a lot on the inside, and in the winter, the wind will be stronger against your knees.
I installed each part with temporary fixation, but the position of the hole did not match, so I had to process the long hole and
I had to drill new mounting holes.
But for less than half the price of OEM, it's good enough for Cost performance!
I'm not angry because I imagined this much from the beginning (hole misalignment and deformation).
I think anyone can install it if they can drill the holes.
Best of all, it's much better than wearing OEM rags!
View detail
Fits: HONDA DIO(4Cycle), HONDA DIO(4Cycle)
If you're okay with it, you can buy it.
[Intended use]
The exterior of AF68 DIO that I got from an acquaintance was tattered, so I took a chance and bought it.
[How is it used?
1000km since I bought it.
Was the one you received as per Image?
The exterior Parts of the Other Brand Product were as Image in a bad way.
I had heard stories about how the dust didn't fit.
First of all, there were many White scratches on the surface even before I took the product out of the DanBall. The BALI of the mounting holes is also terrible.
Was the installation difficult?
The mounting holes do not match by any stretch of the imagination.
There are a few places here and there where there are no holes when compared to OEM.
On top of that, I got a triple Combo:no Instruction Manual.
If the hole doesn't fit by any means, I use Tie Wrap to stop it.
How was your experience with it?
The surface could be put on like that, so I'll give it a minimal circle.
[Included Parts:were they on?
None
Bolts have to be diverted from OEM.
[Was there anything that disappointed you? Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
[Availability and clarity of the Instruction Manual
I can't talk about it because it's not attached in the first place lol.
[Point and hang of installation].
You have to install it with your spirit.
If the hole doesn't fit, Tie Wrap it!
[Opinions and requests to Manufacturer
I doubt the quality of the manufacturing. I wonder what kind of dimensional instructions they put in to make such a terrible product.
View detail
Price.
It's dry, though.
I bought this cheaper one because my OEM Leg shield was ruined.
good point
Cheap.
The position of the Bolt is neat so it is easy to install.
I thought it was easy to paint.
A bad point
●Thinner than OEM, so less strong.
So, it is easy to make a hole when you put Emblem.
The area around the exhaust system is easily deformed by heat.
As a solution, near the exhaust system, Cut or Paper is used to take a little clearance and make a gap.
Maybe it's wrong to compare with OEM because the price is low, but it's not as good as OEM.
As for Merit, I want to keep it inexpensive like I do. Or if you want to add some color to your Leg shield, it's good. Depends on how you use it.
View detail
Fits: HONDA LIVE DIOZX, HONDA LIVE DIOZX, HONDA LIVE DIO, HONDA LIVE DIO
For Refresh
Purchased for the LIVE DIOZx Refresh.
If the OEM Seat is torn and Sponge gets wet, the hole in the back side of the Helmet in will be flooded with water, so I replaced it.
Compared to OEM products, BALI and other products are not as well made.
In the case of exchange, they told me to exchange the whole bracket, but the bracket did not come off.
I installed it without replacing it.
It closes, but there is a Wobble and it floats slightly, so I'll get to it later.
I would like to replace the Bracket as well.
It's a so-so price, but it has Sponge quality and BALI, at Tucker.
We'll see how durable it is in the future as it's not as well hammered.
View detail
A fraudulent product!
This is not a Level product that should be handled Even more so because I trusted this Site
It has fingerprints and scratches, and the packaging is MirrorMatte only
There is no Package No matter how much it is CHINA, there is no such thing
Do the buyers know how to handle it, or is the Rubber frame around the Mirror partially floating around, too? I did
View detail
Windbreak performance is a degree of relaxation.
Somehow thoughtful purchase.
Mounting on M109R.
Backlash etc. There is no sense of instability.
I can firmly fix it.
The windproof effect is reasonable.
It is better than not attaching it, is it?.
Plating processing is a beautiful finish unexpectedly.
View detail
Delimiter degree
- Rust inside the Exhaust pipe
- Exhaust Guard Rust behind
- Exhaust Pipe Guard thread, 3 out of 3 Quantity : 2pc. Set was crushed
- Can not be installed unless the Exhaust Pipe Guard is extremely deformed
- The gap between Rear tire Side wall and Small finger degree
- The distance to the Oil tank is getting closer.
I thought about returning in the above point, but the procedure seems to be difficult,
Wound arrived lightly when fitting, so forcibly installed.
If you continue to ride, even if you make a price difference four times, it is more secure to buy an OEM.
View detail
Is not it good?
I purchased Side cover of Hirochee several times before, but since it was out of Hirochi's Lineup, purchase this Manufacturer's Cover.
Both price and quality are inferior to Hirochi's Cover.
First of all, there are many small scratches (Although it became Mashi with Wax & Armor All containing Compound) I feel that the sled is Large and the installation is hang.
If you are concerned OEM may be Recommendation.
View detail
Fits: YAMAHA APRIO, YAMAHA APRIO, YAMAHA APRIO
APRIO SA11J was equipped. Too, there was much BALI, and fitting was bad and some processings and repair were required of the quality as ? price. -- since it did not expect to there from the first, the price is also reasonable --
APRIO SA11J was equipped.
Too, there was much BALI, and
fitting was bad and some processings and repair were required of the quality as ? price.
-- since it did not expect to there from the first, the
price is also reasonable --
--
which was not regretted in particular -- since it is this price, to those who process it by themselves, I think that it is a Recommendation!
View detail
Fits: YAMAHA APRIO, YAMAHA APRIO, YAMAHA APRIO
Since tabling had shifted delicately that it was pure, the crevice between some arose. But it is tolerance individually.
Since tabling had shifted delicately that it was pure, the crevice between some arose. But it is tolerance individually. View detail