Reviews
As a Leg shield for CUB PRESS
It's deformed a lot on the inside, and in the winter, the wind will be stronger against your knees.
I installed each part with temporary fixation, but the position of the hole did not match, so I had to process the long hole and
I had to drill new mounting holes.
But for less than half the price of OEM, it's good enough for Cost performance!
I'm not angry because I imagined this much from the beginning (hole misalignment and deformation).
I think anyone can install it if they can drill the holes.
Best of all, it's much better than wearing OEM rags!
View detail
Fits: HONDA DIO(4Cycle), HONDA DIO(4Cycle)
If you're okay with it, you can buy it.
[Intended use]
The exterior of AF68 DIO that I got from an acquaintance was tattered, so I took a chance and bought it.
[How is it used?
1000km since I bought it.
Was the one you received as per Image?
The exterior Parts of the Other Brand Product were as Image in a bad way.
I had heard stories about how the dust didn't fit.
First of all, there were many White scratches on the surface even before I took the product out of the DanBall. The BALI of the mounting holes is also terrible.
Was the installation difficult?
The mounting holes do not match by any stretch of the imagination.
There are a few places here and there where there are no holes when compared to OEM.
On top of that, I got a triple Combo:no Instruction Manual.
If the hole doesn't fit by any means, I use Tie Wrap to stop it.
How was your experience with it?
The surface could be put on like that, so I'll give it a minimal circle.
[Included Parts:were they on?
None
Bolts have to be diverted from OEM.
[Was there anything that disappointed you? Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
[Availability and clarity of the Instruction Manual
I can't talk about it because it's not attached in the first place lol.
[Point and hang of installation].
You have to install it with your spirit.
If the hole doesn't fit, Tie Wrap it!
[Opinions and requests to Manufacturer
I doubt the quality of the manufacturing. I wonder what kind of dimensional instructions they put in to make such a terrible product.
View detail
Price.
It's dry, though.
I bought this cheaper one because my OEM Leg shield was ruined.
good point
Cheap.
The position of the Bolt is neat so it is easy to install.
I thought it was easy to paint.
A bad point
●Thinner than OEM, so less strong.
So, it is easy to make a hole when you put Emblem.
The area around the exhaust system is easily deformed by heat.
As a solution, near the exhaust system, Cut or Paper is used to take a little clearance and make a gap.
Maybe it's wrong to compare with OEM because the price is low, but it's not as good as OEM.
As for Merit, I want to keep it inexpensive like I do. Or if you want to add some color to your Leg shield, it's good. Depends on how you use it.
View detail
Fits: HONDA LIVE DIOZX, HONDA LIVE DIOZX, HONDA LIVE DIO, HONDA LIVE DIO
For Refresh
Purchased for the LIVE DIOZx Refresh.
If the OEM Seat is torn and Sponge gets wet, the hole in the back side of the Helmet in will be flooded with water, so I replaced it.
Compared to OEM products, BALI and other products are not as well made.
In the case of exchange, they told me to exchange the whole bracket, but the bracket did not come off.
I installed it without replacing it.
It closes, but there is a Wobble and it floats slightly, so I'll get to it later.
I would like to replace the Bracket as well.
It's a so-so price, but it has Sponge quality and BALI, at Tucker.
We'll see how durable it is in the future as it's not as well hammered.
View detail
Fits: YAMAHA APRIO, YAMAHA APRIO, YAMAHA APRIO
APRIO SA11J was equipped. Too, there was much BALI, and fitting was bad and some processings and repair were required of the quality as ? price. -- since it did not expect to there from the first, the price is also reasonable --
APRIO SA11J was equipped.
Too, there was much BALI, and
fitting was bad and some processings and repair were required of the quality as ? price.
-- since it did not expect to there from the first, the
price is also reasonable --
--
which was not regretted in particular -- since it is this price, to those who process it by themselves, I think that it is a Recommendation!
View detail
Fits: YAMAHA APRIO, YAMAHA APRIO, YAMAHA APRIO
Since tabling had shifted delicately that it was pure, the crevice between some arose. But it is tolerance individually.
Since tabling had shifted delicately that it was pure, the crevice between some arose. But it is tolerance individually. View detail