Reviews
Allows you to turn your Motorcycle around in a comfortable position
I bought it because I wanted to enter the garage from the front of the Motorcycle and park it, then turn it around 180 degrees for the next time I exit (I wanted to keep the front of the Motorcycle facing the garage exit side).
There is a similar product, Motorcycle Moveretc., which is used to lift the rear tire by stepping on it with the foot (by the principle of leverage), but when I tried one owned by a friend, I found that this product was easier to position myself in and moved the motorcycle stably. However, since the Side Stand is dragged, I think it is necessary to use it with STANDRoller for vehicles with LargeEngine Displacement Volume. (The same applies to the Motorcycle Mover.)
In terms of price, it is less expensive than Motorcycle Mover, and the quality is not bad, so we felt that Cost performance is high.
STANDRoller is sold separately, but the Quantity:It would have been better if it was a Set sale.
View detail
Fits: HONDA CR250R, HONDA CR125R, HONDA CRF250R, HONDA CRF450R, HONDA CRF450RX, HUSQVARNA FC250, HUSQVARNA FC250, HUSQVARNA FC350, HUSQVARNA FC350, HUSQVARNA FC450, HUSQVARNA FC450, HUSQVARNA FE125-501, HUSQVARNA FX350, HUSQVARNA FX450, HUSQVARNA TC125, HUSQVARNA TC125, HUSQVARNA TC250, HUSQVARNA TC250, HUSQVARNA TE125-501, HUSQVARNA TX125
Convenient and lightweight! But low strength
Large change is useful for washing the underside of the Motocrosser!
However, it is so strong that it will bend if you try to start KICK with STAND applied.
If it only supports the weight of the car, there is no problem.
The handlebar can be used as an insert, making it easy to insert into an Axle Shaft.
View detail
Used for RM125
I use it to Lift up my RM125.
I thought that the Rail type would be too tight for the Racer's ride height, so I decided to go with this one.
Surprisingly, however, the height was just a little above the lower limit of the adjustment range and just below the belly.
It seemed that even the Girito Rail type could be lifted up.
View detail
For forest road
We chose it for Puncture repair on forest roads.
Lightweight Compact is good.
View detail
StemMaintenance
I purchased a nut removal tool for bearing maintenance of Stem, OEM product is expensive and not used often.
The Torque wrench can be attached to the end of the Torque wrench, so the Torque is large and sturdy.
View detail
Convenient for Torque management!
Used when replacing Rear Sprocket on CRF-125F.
I was having trouble getting my Torque wrench to fit in the gap because the SprocketNut is on the hub side, so I found out about this product and purchased it.
The wrench can be inserted into a narrow space and tightened with a 9.5 insert angle tool.
View detail
For cleaning inside Dust Seal
I use it to clean the inside of dust seals, etc. I am worried about scratches if I pry with a screwdriver, etc. With this, I can shift the scratches on the dust seals to the smallest original size. View detail
Nothing beats Center Stand
I'm having a hard time finding a motorcycle these days that doesn't have a center stand....
I considered the Maintenance Stand, but I wasn't sure about it, so I decided to go with this simplified version.
We also have EasyLift type STAND, but this one is better in that the front tire can be floated.
However, both front and rear tires slide on the roller in a direction other than the direction of rotation, so they do not turn well.
I guess I need to get used to it...
It is much better than nothing, but as the Title says, I miss Center Stand.
Also, there was a small dent on the roller.
It is good because it does not interfere with the operation.
View detail
To MOTARD.
This was the lowest height available for use on MOTARD (DR-Z), which has a low minimum ground clearance.
As shown in the existing Review, the system adjusts the height by rotating the top panel, but there is no way to fix it in place, so it seems somewhat unstable.
The suspension can be lifted under the motorcycle by stepping on it with the foot and lifting it up with the hand, in the same way as applying a center stand. The stepping foot is reversed, though.
View detail
That was a little bit harsh.
I purchased this for front end maintenance on my Grom.
I expected that, but in the case of the Grom, the light surrounds would have to be removed before it could be used.
It was like... But
Until now, when servicing the front of the car, it had to be raised with a jack or similar device.
I feel totally safe when I see it from there.
Well, I'll just take the lights off.
I can now service it with peace of mind.
View detail
More than the price
Used in the maintenance of en Duro bike.
No matter how light the weight is, it will exceed 120 kg if fuel is included, so it is a bit difficult to raise and lower to ”normal” Off-road Stand.
In addition, the Off-road Stand on which the entire Under Guard is placed is not stable due to the Bolt of the Under Guard.
This STAND can lift about 120 kg, even with a child's weight, and the narrow footprint of the motorcycle makes it surprisingly stable.
If it could be raised 5cm higher, there would be no complaints. It is 3Rank higher than a similar product from PROducts.
View detail
Chain Cleaning
I bought this for cleaning the chain and was not sure whether to use STAND or not, but I decided to use this one, which takes up less storage space. I was worried about whether the tire would turn easily until I used it, but it turned perfectly. I was able to clean the Chain without any trouble. The price is cheap and I think it is a good product. I would say it is worth the price. It seems to last for a long time. I forgot to take a picture... View detail
Stable, long-term jack-up is OK
Before purchasing this product, I was maintaining the front area by using a shaft type Rear Stand on a hollow FrontShaft, but I was worried about using only the WoodBlock under the Engine to take the Front fork out for OH, so I purchased this product.
DucatiSCRAMBLER's Stem shaft bore is 27?, so there is no rattling with the included Adapter.
There is some wobble during jack-up, but once it is up, it is firmly settled.
(During the Jack-up, there was an earthquake of about 3 on the Richter scale, but Large was strong.)
The only drawback is that when the jack is jacked up at the lowest hole position, the jack is right at the front shaft, making it difficult to insert and remove the shaft.
When inserting/removing STAND under the Stem shaft, since it is a Front Fender and Limit, I think it would be better to apply Dustcloth on the Fender if you are concerned about it.
View detail
To remove Dust Seal
[How is it used?
Fork oil leakage on HUSQVARNA TE250i after Enduro race and off-road driving, sometimes after washing the car.
RiskRACING SEAL DOCTOR Seal Doctor to take Fork's Garbage. Dust Seal Remover I bought this product to get a Dust Seal at
Before I bought this product, I had to carefully remove the dust seals with a slotted screwdriver, but with Remover, I can easily remove the seals and clean the forks much easier.
The price is inexpensive and I highly recommend it to Off-road riders.
View detail
If I have trouble with Space, I will put it on.
If I have trouble with Space, I will put it on.
The Handlebar area of the revolver often has trouble with Space, which interferes with Handlebar navigation, so I'm going to solve this problem by adding this to the revolver.
View detail
Light thin strong!
Good product
It is a light, thin, easy to apply force handle, a tool that is rarely used but is a necessity.
View detail
Simple
I bought Wire twister and I bought Wire at the same time.
I immediately tried Wiring it, but it was stronger than I expected and harder to cut, even when I twisted it to the limit to try it out.
It is not too hard and is very easy to use.
View detail
Mounted face down.
[How is it used?
I use it on my Z900.
We replaced it because the other company's product we had been using was outside of the Screen, which made us uneasy while driving, and it interfered with the Screen when we fixed the phone.
Was the one you received as per Image?
It was just as shown in the Image. I thought it didn't look too cheap.
Was the installation difficult?
The installation itself is easy, but in my case, when I installed it as usual, it still interfered with the Screen itself, so I installed it upside down.
As a result, this was the right choice, and the mounted phone is now easier to see and Smooth to wear.
How was your experience with it?
It has only been running for a short time after installation, but it looks quite good with no blurring.
I will use the same product in the future in case of deterioration or accidental damage.
Attached to the bar itself is a SP Conecto Smartphone Mount and a USB×2.
If you pack it up, you could probably fit at least a WearLOVE LeCamera.
View detail
Off to load the car.
[How is it used?
Purchased to securely fasten to off-road motorcycle transporter loading.
Although there were also products made by DRC and OGUshow, we chose this product because of its price and the statement that it is exclusively for off-road vehicles.
Was the one you received as per Image?
The box in which it was packaged was larger than I had expected.
How was your experience with it?
I knew before I bought it that this product alone would not be enough to keep my Motorcycle upright.
The performance of the wheel chock cannot be achieved unless the Transporter is fixed to the floor or a concrete panel is purchased separately to fix the Wheel chock.
I thought it would be easier to fix it if the width was a little narrower. 21in. off-vehicle front wheel is too stiff.
View detail
A little less Grease?
[How is it used?
I am riding a SEROW225. Even with the lowest setting on the Lift Stand for regular off-road motorcycles, there was not enough ground clearance under the belly of the SEROW, so I had to lift it up a bit. When I found out that there is a lift stand for TRAIL with lower ground clearance, I thought I would like to have it someday.
Was the one you received as per Image?
It is very heavy. There is an assembly element, which I found a bit cumbersome. It took a moment. Tools are not included.
How was your experience with it?
Large success! It's so easy to get under SEROW's belly!
I like that the receiver is a Wide design, so I don't have to think about where the center of gravity is!
However, I felt that the shape and material of the Bracket, which is used to step into the Lift Stand, makes it more difficult to transmit force compared to other Lift Stands.
And it can be used normally for regular Full sizeRacer as well. If you have both, this would be the one to choose.
[Points to note]
It is partially but necessary to assemble it by yourself.
How did it compare to other products?
It is much easier to use than a regular Off-road Stand because of its lower minimum height!
However, the lightness of Lift up feels heavier than DRC's. Body weight also seems heavier. It does not bother me that much.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
When assembling, it may be helpful to slightly grease up the moving parts to make the movement smoother.
View detail