Reviews
StemMaintenance
I purchased a nut removal tool for bearing maintenance of Stem, OEM product is expensive and not used often.
The Torque wrench can be attached to the end of the Torque wrench, so the Torque is large and sturdy.
View detail
Convenient for Torque management!
Used when replacing Rear Sprocket on CRF-125F.
I was having trouble getting my Torque wrench to fit in the gap because the SprocketNut is on the hub side, so I found out about this product and purchased it.
The wrench can be inserted into a narrow space and tightened with a 9.5 insert angle tool.
View detail
For cleaning inside Dust Seal
I use it to clean the inside of dust seals, etc. I am worried about scratches if I pry with a screwdriver, etc. With this, I can shift the scratches on the dust seals to the smallest original size. View detail
To remove Dust Seal
[How is it used?
Fork oil leakage on HUSQVARNA TE250i after Enduro race and off-road driving, sometimes after washing the car.
RiskRACING SEAL DOCTOR Seal Doctor to take Fork's Garbage. Dust Seal Remover I bought this product to get a Dust Seal at
Before I bought this product, I had to carefully remove the dust seals with a slotted screwdriver, but with Remover, I can easily remove the seals and clean the forks much easier.
The price is inexpensive and I highly recommend it to Off-road riders.
View detail
Light thin strong!
Good product
It is a light, thin, easy to apply force handle, a tool that is rarely used but is a necessity.
View detail
Simple
I bought Wire twister and I bought Wire at the same time.
I immediately tried Wiring it, but it was stronger than I expected and harder to cut, even when I twisted it to the limit to try it out.
It is not too hard and is very easy to use.
View detail
Good for Torque management of Cylinder head as well as Sprocket.
I bought this product because my car is a 2st Enduro racer and I expect to do engine OH frequently. As the name of the product suggests, it is useful not only for the torque management of the rear sprocket but also for the torque management of the cylinder headBolt. This product is excellent as an attachment for torque management. View detail
Unit Steering Stem Wrench
I used it to check the Torque when I replaced the Stem bearing.
The Torque wrench is used to set the Torque value, so you can go Large without any experience.
It's also a good way to see how much force you need to tighten.
It's not easy to make pre-Road adjustments.
However, you have to reduce the Torque value to account for the length of this tool. (It's a pain in the ass, so I used a slightly reduced value)
View detail
If only it was a little thinner …
These Snap Ring Pliers are surprisingly nice to have
Slotted screwdrivers and pliers are good for power, but Special tools are still useful
I bought it to remove the Snap ring that is sometimes used on the rear wheel hub
It was a wheel of FTR223 and I was able to remove it easily
Snap rings are sometimes used for Oil SealStopper, such as Front fork, and It is a good idea to have one to work with
If I had to pick one MinusPoint, it would be nice if the tip was a little thinner
A Large-textured Snap ring is no problem, but a Small-textured Snap ring And the hole that is drilled to insert the tip of this Snap Ring is small If you're a Pliers, you may not get in
You can ignore the hole and force the Snap Ring Pliers off by placing them around the hole You can do it, but I wish it was just 0.5mm thinner, and sometimes I think "hellip There was
In my case, I shaved the tips of the Pliers to a fine point, but I probably wouldn't sell them in this condition I guess it's a product safety strength issue
There's nothing wrong with the product, just that I'm trying to fight with this one pc and there's nothing wrong with the product It is not
The price is affordable and if it's fit for purpose, it's Recommendation
View detail
Though it is usable
We were able to replace Spring of Mono Suspension of fzs 1000. However, reservoir Tank integral type suspension (Especially Tank's sideways sideways) However, with regular usage it was not possible to hook Spring, it was decided to use trial and error.
I think that it is very easy to use and good products if it can be fixed firmly to the upper part of the suspension.
Those who think that they would like to use from now on, I think that it is better to look at the pictures and judge purchase based on whether or not they can fix.
Regarding durability, there are things that are not genuine usage, but since Screw Mountain has been shattered considerably, it is a feeling that it is likely to become useless for the second time.
View detail