Reviews
It works great! I couldn`t use it on my Rebel 1100.
I bought this product to try to maintain the rear area.
It can be used on GSX250R without any problem.
The Rebel 1100 could not be used because the Swing Arm and Exhaust System interfered with each other due to their proximity.
If I remove the Silencer Only, I can use it.
View detail
Cost performance is good.
It is more solid and secure than I expected.
The U-shaped part is deep enough to fit on the Stand Hook and prevent it from coming off, so you can use it with confidence. The color is black, so it goes well with motorcycles.
View detail
Convenient
I use it on my SEROW 250.
If you forget to check the minimum ground clearance and use it in SEROW, it is a little high (lol).
So I lifted it up a little and put it on.
This is the first time I've bought one of these, and it's pretty heavy when you lift it up.
I found it a little easier to use the Image to apply the Center Stand.
View detail
Work efficiency is improved by several steps.
for RaceEngine's Overhaul.
It's very handy to have because I take it apart about once a year.
Small TypeEngine can be disassembled without it, but I think it is worth to buy it to assemble accurately in a short time.
View detail
Affordable.
This is a great way to improve the atmosphere of your garage, protect the floor, prevent scratches from the STAND directly hitting the concrete, etc. When the STAND is not in use, you can use it as a place to place parts during maintenance to prevent them from rolling or flying around. If you want to use it as an underlay for STAND, it is limited to MXSTAND or a simple type of STAND (purchase their product at the same time) that is lifted by applying it to the Under Guard of Off car. If you want to use Front StemSTAND and Rear StemSTAND at the same time for serious maintenance, it is better to buy Full size RACINGMatte. View detail
I'm always ready.
I was able to help when Chain was crushed in Hokkaido and when Tire was nailed in Shimane.
There's nothing sadder than being out of action on the road and having to retire, so the more prepared you are, the better.
View detail
Unit B2510 Front Stem Upstand
I bought a front roll-up on a YAMAHA YZF R1. The tackle is very good to use. The kit includes instructions and fasteners for different motorcycle manufacturers. I recommend everyone to buy, especially those who service their own motorcycle. View detail
Unit Unit B2510 Front Stem Up Stand
ZX25r I bought it because I needed it to replace my Handlebar.
I was able to use the special tip separately without any problems.
Very convenient
View detail
Motivation for maintenance
[How is it used?
I bought this to prevent the table from getting dirty when I disassemble the parts in the garage.
I thought I could get on the Tool chest if I wanted to! I thought I could ride on the Tool chest, but the size didn't match with my Tool chest. (It says Size, so I'm telling you to measure it.)
Was the one you received as per Image?
It was Matte as per Image.
I thought it would be a thin PeLePera feeling because it was inexpensive, but I was surprised at how good the texture was.
How was your experience with it?
The texture of the surface is not too fluffy and not too hard, which is the best for placing parts.
The Rubber on the back does a good job and even when unfolded right after opening the package, it doesn't curl up or act as a non-slip surface.
I was going to use it properly in Garage, but I liked it so much I was a little hesitant lol.
How did it compare to other products?
I was wondering if I should go with brembo Matte, but I got the impression from the pictures that it was thin, so I went with this one.
Also, I rarely use brembo parts, so....
【Review】
The texture is better than I expected and I am satisfied.
If you're on the fence, buy it, it'll take your motivation to do maintenance at Garage to the next level!
View detail
Unit B2510 Front Stem Upstand
I've never had a motorcycle front slide. I wanted to buy for a long time and still bought it. And now I have no regrets. Honestly, at first, I could not understand how he would hold the bike, since there are no restraints. But it turns out he holds the motorcycle under his weight. Now I can easily change the front tires, disassemble the fork. He is the right thing for your motorcycle. Recommend! View detail
The height...
I bought this because I wanted to use it for maintenance of SEROW, but the height is quite high. (Sweat) After all, I could not put SEROW on it by myself. I think it is easy to put it on if I devise something.... If it's a tiger truck, it's light enough to be loaded by one person. It would have been nice if it was a little lower. I am satisfied with the product because it is well built. If it was a little lower, I would have reduced the rating by one. View detail
Car models where the rear stand cannot be used
I was surprised at how durable it was.
I bought it for the maintenance of the rear area because the rear stand cannot be used in my car.
It lifts without a problem.
However, the lever whist is good for hanging.
View detail
It's not gonna blow!
[How is it used?
I use it to fix the grip of my off-road motorcycle.
Usually when I change the Grip, I apply SUPERX and then wrap the Wire in 3 places.
So far I haven't had any problems with the Grip turning by securing it with a double layer.
Was the one you received as per Image?
It is just like the image. It's a nice large size.
How was your experience with it?
I love the lid, it's super nice.
If you use a wire that is just wrapped around a Bobbin, before you know it, it will explode in your toolbox or you'll be like, "Where's the end? But this product does not happen. It is the best.
[Points to note]
Not particularly
How did it compare to other products?
There is no need to compare with other products. There is no other option but to buy this.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
Wire Twister Pliers (Auto Return Type) (https://www.webike.net/sd/544991/)
I bought this one at the same time. It's not a tool that will break, so buy it once and it will last you a lifetime, so buy it.
View detail
For Tire Cleaning
I bought it to clean the front tire when cleaning the motorcycle.
When you put the front tire on the WheelRoller, if you don't put the front tire on the WheelRoller in the middle of the wheel parallel to the front tire, when you turn the front tire, it will come off from the Rollers.
I have to start over from the beginning. It takes experience, but no matter how many times I try, it's hard to get the pit parallel and right in the middle.
Turning the Tire is awkward and requires a lot of force.
If you do not use the Rear stand, the Motorcycle is leaning and is dangerous.
I always use it for cleaning after Touring, I use it for a long time and it is durable.
View detail
Purchased for Chain cleaning
[How is it used?
I bought this to make things easier for Chain cleaning.
I also own Racing Stand, but because there was anxiety in one person when I put Racing Stand on CBR because there were few parts to hold and support, I decided on the product here which only needs to be pushed and put on.
Was the one you received as per Image?
The texture is heavy and sturdy as it has a load capacity of up to 200kg.
The rollers can be adjusted to three levels to suit the tire diameter.
For 17in. it was just right in the middle.
There is a slight gurgle in the Roller's rotation, and it would be nice if it rotated more smoothly.
There was no particular problem in use though I thought that the usable tire width was Limit before purchase because it was said that it was up to 200mm.
How was your experience with it?
When turning the Tire, it feels like it takes a little effort with a vehicle weighing about 200kg.
This is a difficult one as it will vary from vehicle to vehicle.
The price is cheap, and it is a product that can be used enough if it is only Chain cleaning and Wheel cleaning.
It's more compact than the Racing Stand (approx. 345mm long, 210mm wide and 40mm high) so it takes up less space to store.
[Points to note]
When I turn the Tire, the bike is a little bit wobbly, so I use Elastic band etc. to make the brake work.
How did it compare to other products?
I don't know because I haven't compared them.
View detail
Garbage
I am Garbage.
The weld of the bar on the Screw part of the pedestal was tilted.
I managed to fix it with a Rubber Hammer, but I almost knocked over the Motorcycle! 。
The Damper also has a narrow range of effect and there is a shock when lowering the Motorcycle.
BootsSTAND and the welding of a good UNIT product is really inaccurate.
I should have bought the DRC honestly.
I will never buy a product made by unit again.
View detail
Cosmetically, it's alright. The only thing I wish I'd known before I bought it was that ……
I bought this to service my Off car.
When I bought it, I was worried about which one to use with HC2STAND of DRC, but I chose this one because the price was cheap.
It takes quite a bit of hang to lift, or I think that point is the same for all Off-road stands.
The only point is that this product does not have a lock function on the top panel, so when you lift the product, the body is not in quantity.:Pair (for Left and Right) It will move to the It is possible to take measures by fixing it with something, but I think that it is a matter that I want to know before I buy it if possible.
View detail
It's convenient
It is convenient. I have no choice but to say.
The basic purpose is to clean the Chain.
Because it is an Off car and I want to clean it on the way back from Touring and forest road.
However, a regular STAND takes up a lot of space and...
I've got two with On, and the Maintenance Stand (front and back) on that one already takes up a lot of space.
It's very easy to use. Once you adjust the length, you don't even have to hang.
I think anyone can handle it easily.
It's not something I'd pass around, but there's no reason not to buy it.
View detail
Easy to use!
I used it on my 177cc motorcycle which weighs 115kg and it did not move the gap when I put the vehicle on it and I was able to handle the rear wheel idling easily.
However, it may take a little effort to spin the rear wheel if the vehicle is at the weight limit.
It is a good idea to occasionally lubricate the roller bearings. A good product should be used for a long time.
View detail
GSX1300R HAYABUSA is Large strong even if it hangs?
I thought I would use a single pipe to replace the stem bearing on my GSX1300R Hayabusa, but I thought it would be too much work to assemble and disassemble, so I bought this product.
The maximum load capacity is 180kg, so is the GSX1300R HAYABUSA, which weighs almost 270kg, large and strong? I thought that I could go because I only hang the front. (Please do so at your own risk.)
Some people use a Ratchet Tie downBelt to hang it, but when you take it down, it falls all at once, so I recommend a lightweight Lever whist.
View detail