Reviews
Fits: HONDA APE, HONDA BENLY50, HONDA DAX, HONDA MONKEY, HONDA CT110 HUNTER CUB, HONDA GB250 CLUBMAN, HONDA FTR223, HONDA CL400, HONDA FTR220, YAMAHA SRV250, YAMAHA RENAISSA, YAMAHA BRONCO, YAMAHA TW225, YAMAHA TW200, YAMAHA SR400, YAMAHA SR500, SUZUKI VANVAN, SUZUKI GN125, SUZUKI GS125, SUZUKI VOLTY
Not very good
The paint on some of these has a bumpy texture, like the units weren't clean when the paint was applied. One of them had an electrical short upon installation which was popping my signal fuse. Luckily I had bought a spare. Installaton wasn't a big problem, but I wish they used thicker gauge of wire, it's very thin. Very inexpensive blinkers, but you get what you pay for. I wish I had spent a little more and gotten better quality blinkers. View detail
Fits: その他 12V car
dark
The Front as well as the Rear are dark.
It is actually rated ??1, but I changed it to ??2 to account for the fact that it is being changed to a Smoked lens.
View detail
Fits: その他 12V car
It's dark
Not enough illumination. From a fellow who went Touring with me. "can not see" It was pointed out to me that this is not a problem at night. I think it is fine at night, but in good weather during the daytime, visibility is insufficient. I have a Blinker lens. [Color] I think some of them are in Smoke, so I decided to use ??2. By the way, the Right Side of the image is our product. I thought it was dangerous, so I bought brighter LEDs. (Left Side) View detail
I installed it on HORNET250
I put it on RearBlinker The Valve which was originally attached to the RearBlinker was T13
I looked for T13 but didn't have it, so I ended up using this instead (Because I thought that T16 is too large
The color is yellow and when you look through the Orange Lens, it looks like white It may be a little hard to see in direct sunlight, but I felt it was a little darker on the HORNET (more If it's a small car, it may not be a problem I was aiming for more brightness with LED, so I ended up with a 9 series SMD unit from Sun Yat-sen Replaced it (The brightness is up.)
The lesson is that, after all, the performance of LEDs is, to some extent, proportional to the price
View detail
Fits: その他
Coil sound and color is strange
At startup, there is a large Coil sound, and when repeating hi→low, there is a little sound Smaller works
I bought the 6000k and it's a green color with yellowish browns
It's so much darker than the 35w HID's I used to wear!
As it is 10 days after purchase, it seems to be unable to be returned and exchanged, so you have to be patient and use it It is not
A small, small drawing of a small Construction Manual in Japanese If you can build it by yourself, there will be no problem, but it is not kind to amateurs Yes
Wiring and coating do not seem to be bad, there was no tape peeling or defective terminals It's solid here
Rather than getting power from the Battery, you can connect to the Headlight without connecting it to the Battery Coil noise is a little better if you take it away from the wiring, just because it's better doesn't mean it doesn't sound But …
After a few minutes of running, it doesn't matter, and soon the Coil noise will gradually become small and stop
The cord for the terminals is a little short, and it's a little difficult to install on a Sports-type motorcycle I had a hard time with it This depends on the Motorcycle, so I don't blame you
It's a Minus with Coil sound and a Minus with Large sound
Minus in color, not so bright and even more minus
Very disappointing product, I can't help but say that I would not recommend it at all
The picture is of the OEM Light and HID
View detail
Fits: その他
Since the portion of a pin is long and slender, if it actually attaches, the moment the metal side grounded, the light will be switched on, but the light is not switched on in order that a pin may separate, if a Valve is turned. I think that a pin must b
Since the portion of a pin is long and slender, if it actually attaches, the moment the metal side grounded, the light will be switched on, but the light is not switched on in order that a pin may separate, if a Valve is turned.
I think that a pin must be melted, and it cannot but change and equip with a form by a Solder iron since it is
.
View detail